Difference between revisions of "6 Channel Relay Driver Card"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
== Features == | == Features == | ||
| − | * Drives [https://qrp-labs.com/ultimatelpf.html QRP Labs Ultimate relay-switched BPF/LPF kit] | + | * Drives relays on [https://qrp-labs.com/ultimatelpf.html QRP Labs Ultimate relay-switched BPF/LPF kit] |
** Drives either receiver Band Pass (BP) Filters or transmitter Low Pass (LP) Filters | ** Drives either receiver Band Pass (BP) Filters or transmitter Low Pass (LP) Filters | ||
** Open collector to turn on/off relay | ** Open collector to turn on/off relay | ||
| Line 28: | Line 28: | ||
* [https://qrp-labs.com/ultimatelpf.html Ultimate relay-switched LPF kit] | * [https://qrp-labs.com/ultimatelpf.html Ultimate relay-switched LPF kit] | ||
** [https://qrp-labs.com/images/ultimatelpf/assembly_ulpf2.pdf Ultimate relay-switched LPF kit Build Instructions] | ** [https://qrp-labs.com/images/ultimatelpf/assembly_ulpf2.pdf Ultimate relay-switched LPF kit Build Instructions] | ||
| − | * Takes five [https://qrp-labs.com/bpfkit.html QRP Labs Bandpass Filters] | + | * Takes five [https://qrp-labs.com/bpfkit.html QRP Labs Bandpass Filters] or [https://qrp-labs.com/lpfkit.html Low Pass Filters] |
[[file:Ultimate_Relay_Card_5.jpg]] | [[file:Ultimate_Relay_Card_5.jpg]] | ||
| Line 44: | Line 44: | ||
* Jumpers | * Jumpers | ||
| − | === Ultimate Relay Card Jumpers === | + | === Ultimate Relay Card Jumpers - Band Pass (BP) === |
* To switch Band Pass (BP) filters, use the jumper configuration shown below | * To switch Band Pass (BP) filters, use the jumper configuration shown below | ||
Latest revision as of 18:53, 27 January 2022
Contents
Features
- Drives relays on QRP Labs Ultimate relay-switched BPF/LPF kit
- Drives either receiver Band Pass (BP) Filters or transmitter Low Pass (LP) Filters
- Open collector to turn on/off relay
- Drives low to turn on relay
- Other side of relay pulled up to 5V
- User should only turn on one output at a time
- Inputs
- 6 channels (5 used with Ultimate Relay Card)
- Active-high in to drive relay to on state
- 3.3K to transistor base
- 1 mA for 3.3V drive
- 1.5 mA for 5V drive
- Outputs
- Open Collector outputs from 2N3904 NPN transistors
- Power
- 9-14V power in
- 5V power out to power relays
- DC jack
- 36x37mm card
- 3 PCBs for $11 from OshPark
Ultimate Relay Card
Ultimate Relay Card Connections
- The RF input is the RFI pin of the 2 x 5-pin header on the left of the board (same as in the Low Pass Filter kit usage)
- RF output cut the track from the SMA connector center pins and add a wire to connect it to the common bus track that runs horizontally across the board, finishing at the "RF" pad circled in yellow
- Cut/Jumper
- Cut on top side near Vertical SMA
- Jumper on rear side
- Jumpers
Ultimate Relay Card Jumpers - Band Pass (BP)
- To switch Band Pass (BP) filters, use the jumper configuration shown below
Ultimate Relay Card Connectors
- +5V
- B5
- B3
- B4
- B1
- B2
- GND
- RFIn
- GND
- RFOut
Connectors
J1 - Input Connector
- N/C
- IN1
- IN2
- IN3
- IN4
- IN5
- IN6
- GND
J2 - Output Connector
- GND
- OUT6
- OUT5
- OUT4
- OUT3
- OUT2
- OUT1
- 5V OUT
Power Connector
- 7-14V input
- Center positive
Control via VFO-003
- VFO-003
- Band select via menu option
- J8 - Arduino P5-P9
- Arduino pins
- Arduino D5 - 10M select
- Arduino D6 - 15M select
- Arduino D7 - 20M select
- Arduino D8 - 40M select
- Arduino D9 - 80M select
- Vcc
- GND
- GND
Cables
VFO-003 to Relay Driver Card
| RLY_DRVR pin
1x8 BERG |
Signal | Function | VFO-003_Pin
1x8 BERG |
|---|---|---|---|
| 1 | N/C | N/C | |
| 2 | IN1 | 10M | 1 |
| 3 | IN2 | 15M | 2 |
| 4 | IN3 | 20M | 3 |
| 5 | IN4 | 40M | 4 |
| 6 | IN5 | 80M | 5 |
| 7 | IN6 | N/C | |
| 8 | GND | GND | 7 |
Relay Driver to Relay Card
| RLY pin
2x5 BERG |
Signal | Function | RLY_DRVR pin
1x8 BERG |
Signal |
|---|---|---|---|---|
| 1 | +5V | Power | 8 | 5V |
| 2 | B5 | 80M | 3 | OUT5 |
| 3 | B3 | 20M | 5 | OUT3 |
| 4 | B4 | 40M | 4 | OUT4 |
| 5 | B1 | 10M | 7 | OUT1 |
| 6 | B2 | 15M | 6 | OUT2 |
| 7 | GND | RF Gnd | N/C | GND |
| 8 | RFI | RF In | N/C | |
| 9 | GND | Power | 1 | GND |
| 10 | RFO | N/C | N/C | |
| 2 | N/C |
Testing
- Apply 9-12V to DC jack
- Use LED w/ resistor on output to check 5V
- One channel at a time
- Pull up channel input to +5V
- Check output with LED pulled up to +5V out
CAD
