QM Tech Cyclone V FPGA Board

Features

• QMTECH Altera Intel FPGA Core Board Cyclone V CycloneV 5CEFA2F23 SDRAM
  • QMTECH GitHub page
  • On-Board FPGA: 5CEFA2F23I7N
  • On-Board FPGA external crystal frequency: 50MHz
  • 5CEFA2F23 has rich RAM resource up to 1,760Kb
  • 5CEFA2F23 has 25K logic cells
  • On-Board Micron MT25QL128A SPI Flash, 16M bytes for user configuration code
  • On-Board Winbond 32MB SDRAM, W9825G6KH-6
  • On-Board 3.3V power supply for FPGA by using MP2315 wide input range DC/DC
  • 5CEFA2F23 core board has two 64p, 2.54mm pitch headers for extending 108 user IOs. All 108 user IOs are precisely designed with length matching
  • 5CEFA2F23 core board has 3 user switches
  • 5CEFA2F23 core board has 2 user LEDs
  • 5CEFA2F23 core board has JTAG interface, by using 10p, 2.54mm pitch header
  • 5CEFA2F23 core board PCB size is: 6.7cm x 8.4cm
  • Default power source for board is: 1A@5V DC, the DC header type: DC-050, 5.5mmx2.1mm

FPGA

5CEFA2F23 FPGA Resources

• CLK_50M = PIN_BANK_3B_M9

LEDs/Switches

• Power LED = D4 (On when 5V is applied)
• User LED = LED_D5 = FPGA Pin_BANK_7A_D17
• KEY0 = SW1 = FPGA Pin_BANK_4A_AB13
• RESET_N = SW2 = FPGA PIN_BANK_4A_V16
• nCONFIG = SW3 = FPGA PIN_BANK_9A_A4
• JP5 - 5V

SDRAM

SDRAM Pins

• sdRamClk = PIN_BANK_3B_AB11
• sdRamClkEn = PIN_BANK_3B_V9
• n_sdRamCas = PIN_BANK_3B_AA7
• n_sdRamCe = PIN_BANK_3B_AB5
• n_sdRamRas = PIN_BANK_3B_AB6
• n_sdRamWe = PIN_BANK_3A_W9
• sdRamAddr[0] = PIN_BANK_3B_P8
• sdRamAddr[1] = PIN_BANK_3A_P7
• sdRamAddr[2] = PIN_BANK_3B_N8
• sdRamAddr[3] = PIN_BANK_3A_N6
• sdRamAddr[4] = PIN_BANK_3A_U6
• sdRamAddr[5] = PIN_BANK_3A_U7
• sdRamAddr[6] = PIN_BANK_3A_V6
• sdRamAddr[7] = PIN_BANK_3A_U8
• sdRamAddr[8] = PIN_BANK_3A_T8
• sdRamAddr[9] = PIN_BANK_3A_W8
• sdRamAddr[10] = PIN_BANK_3A_R6
• sdRamAddr[11] = PIN_BANK_3B_T9
• sdRamAddr[12] = PIN_BANK_3B_Y9
• sdRamAddr[13] = PIN_BANK_3A_T7
• sdRamAddr[14] = PIN_BANK_3B_P9
• sdRamData[0] = PIN_BANK_3B_AA12
• sdRamData[1] = PIN_BANK_3B_Y11
• sdRamData[2] = PIN_BANK_3B_AA10
• sdRamData[3] = PIN_BANK_3B_AB10
• sdRamData[4] = PIN_BANK_3B_Y10
• sdRamData[5] = PIN_BANK_3B_AA9
• sdRamData[6] = PIN_BANK_3B_AB8
• sdRamData[7] = PIN_BANK_3B_AA8
• sdRamData[8] = PIN_BANK_3B_U10
• sdRamData[9] = PIN_BANK_3B_T10
• sdRamData[10] = PIN_BANK_3B_U11
• sdRamData[11] = PIN_BANK_3B_R10
• sdRamData[12] = PIN_BANK_3B_R11
• sdRamData[13] = PIN_BANK_3B_U12
• sdRamData[14] = PIN_BANK_3B_R12
• sdRamData[15] = PIN_BANK_3B_P12

Programming the FPGA EEPROM

• File
• Convert Programming File
• Configuration Device = MT25QL128
• Mode = Active Serial
• Programming File Type: *.jic
• Advanced = Check both Disables...
• Select Flash Loader
• Add Device = Cyclone V and 5CEFA2
• Select SOF Data
• Select Add File and select the .sof file
• Generate
• In Tools, Programmer
• Mode: JTAG
• Add file and select the .jic file
• Select Program/Configure
• Takes a while to program
• Press button near VGA

Pin List

set_global_assignment -name FAMILY "Cyclone V"
set_global_assignment -name DEVICE 5CEFA2F23I7
set_global_assignment -name TOP_LEVEL_ENTITY TS2_68000_Top
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 18.1.0
set_global_assignment -name PROJECT_CREATION_TIME_DATE "07:21:26  JULY 04, 2020"
set_global_assignment -name LAST_QUARTUS_VERSION "18.1.0 Lite Edition"
set_global_assignment -name PROJECT_OUTPUT_DIRECTORY output_files
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
set_global_assignment -name ERROR_CHECK_FREQUENCY_DIVISOR 1
set_global_assignment -name EDA_SIMULATION_TOOL "ModelSim-Altera (VHDL)"
set_global_assignment -name EDA_TIME_SCALE "1 ps" -section_id eda_simulation
set_global_assignment -name EDA_OUTPUT_DATA_FORMAT VHDL -section_id eda_simulation
set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
set_global_assignment -name TIMING_ANALYZER_MULTICORNER_ANALYSIS ON
set_global_assignment -name SMART_RECOMPILE ON
# Clock and reset
set_location_assignment PIN_M9 -to i_CLOCK_50
set_location_assignment PIN_V18 -to n_reset
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to n_reset
# Serial
set_location_assignment PIN_B11 -to cts1
set_location_assignment PIN_F10 -to rts1
set_location_assignment PIN_C11 -to rxd1
set_location_assignment PIN_G10 -to txd1
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to rxd1
set_location_assignment PIN_L17 -to serSelect
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to serSelect
# SRAM
set_location_assignment PIN_E2 -to n_sRamCS
set_location_assignment PIN_L2 -to n_sRamOE
set_location_assignment PIN_D6 -to n_sRamWE
set_location_assignment PIN_E9 -to sramAddress[19]
set_location_assignment PIN_B5 -to sramAddress[18]
set_location_assignment PIN_B6 -to sramAddress[17]
set_location_assignment PIN_A7 -to sramAddress[16]
set_location_assignment PIN_A10 -to sramAddress[15]
set_location_assignment PIN_A9 -to sramAddress[14]
set_location_assignment PIN_B7 -to sramAddress[13]
set_location_assignment PIN_A5 -to sramAddress[12]
set_location_assignment PIN_D9 -to sramAddress[11]
set_location_assignment PIN_C6 -to sramAddress[10]
set_location_assignment PIN_E7 -to sramAddress[9]
set_location_assignment PIN_G2 -to sramAddress[8]
set_location_assignment PIN_N2 -to sramAddress[7]
set_location_assignment PIN_U2 -to sramAddress[6]
set_location_assignment PIN_W2 -to sramAddress[5]
set_location_assignment PIN_Y3 -to sramAddress[4]
set_location_assignment PIN_U1 -to sramAddress[3]
set_location_assignment PIN_N1 -to sramAddress[2]
set_location_assignment PIN_L1 -to sramAddress[1]
set_location_assignment PIN_G1 -to sramAddress[0]
set_location_assignment PIN_C1 -to sramData[0]
set_location_assignment PIN_G6 -to sramData[1]
set_location_assignment PIN_G8 -to sramData[2]
set_location_assignment PIN_F7 -to sramData[3]
set_location_assignment PIN_H8 -to sramData[4]
set_location_assignment PIN_H6 -to sramData[5]
set_location_assignment PIN_C2 -to sramData[6]
set_location_assignment PIN_D3 -to sramData[7]
# SD Card
set_location_assignment PIN_B15 -to sdCS
set_location_assignment PIN_B16 -to sdMISO
set_location_assignment PIN_C15 -to sdMOSI
set_location_assignment PIN_C16 -to sdSCLK
set_location_assignment PIN_D17 -to driveLED
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sdMISO
# Video
set_location_assignment PIN_A15 -to hSync
set_location_assignment PIN_D12 -to videoR1
set_location_assignment PIN_E12 -to videoR0
set_location_assignment PIN_C13 -to videoG1
set_location_assignment PIN_D13 -to videoG0
set_location_assignment PIN_A13 -to videoB1
set_location_assignment PIN_B13 -to videoB0
set_location_assignment PIN_A14 -to vSync
# PS/2
set_location_assignment PIN_AA2 -to ps2Clk
set_location_assignment PIN_AA1 -to ps2Data
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2Clk
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2Data
# SDRAM
set_location_assignment PIN_AB11 -to sdRamClk
set_location_assignment PIN_V9 -to sdRamClkEn
set_location_assignment PIN_AA7 -to n_sdRamCas
set_location_assignment PIN_AB5 -to n_sdRamCe
set_location_assignment PIN_AB6 -to n_sdRamRas
set_location_assignment PIN_W9 -to n_sdRamWe
set_location_assignment PIN_AB7 -to DQML
set_location_assignment PIN_V10 -to DQMH
set_location_assignment PIN_P9 -to sdRamBA[1]
set_location_assignment PIN_T7 -to sdRamBA[0]
set_location_assignment PIN_Y9 -to sdRamAddr[12]
set_location_assignment PIN_T9 -to sdRamAddr[11]
set_location_assignment PIN_R6 -to sdRamAddr[10]
set_location_assignment PIN_W8 -to sdRamAddr[9]
set_location_assignment PIN_T8 -to sdRamAddr[8]
set_location_assignment PIN_U8 -to sdRamAddr[7]
set_location_assignment PIN_V6 -to sdRamAddr[6]
set_location_assignment PIN_U7 -to sdRamAddr[5]
set_location_assignment PIN_U6 -to sdRamAddr[4]
set_location_assignment PIN_N6 -to sdRamAddr[3]
set_location_assignment PIN_N8 -to sdRamAddr[2]
set_location_assignment PIN_P7 -to sdRamAddr[1]
set_location_assignment PIN_P8 -to sdRamAddr[0]
set_location_assignment PIN_P12 -to sdRamData[15]
set_location_assignment PIN_R12 -to sdRamData[14]
set_location_assignment PIN_U12 -to sdRamData[13]
set_location_assignment PIN_R11 -to sdRamData[12]
set_location_assignment PIN_R10 -to sdRamData[11]
set_location_assignment PIN_U11 -to sdRamData[10]
set_location_assignment PIN_T10 -to sdRamData[9]
set_location_assignment PIN_U10 -to sdRamData[8]
set_location_assignment PIN_AA8 -to sdRamData[7]
set_location_assignment PIN_AB8 -to sdRamData[6]
set_location_assignment PIN_AA9 -to sdRamData[5]
set_location_assignment PIN_Y10 -to sdRamData[4]
set_location_assignment PIN_AB10 -to sdRamData[3]
set_location_assignment PIN_AA10 -to sdRamData[2]
set_location_assignment PIN_Y11 -to sdRamData[1]
set_location_assignment PIN_AA12 -to sdRamData[0]
#50-pin I/O Connector
set_location_assignment PIN_AB15 -to IO_PIN[3]
set_location_assignment PIN_AA15 -to IO_PIN[4]
set_location_assignment PIN_Y14 -to IO_PIN[5]
set_location_assignment PIN_Y15 -to IO_PIN[6]
set_location_assignment PIN_AB17 -to IO_PIN[7]
set_location_assignment PIN_AB18 -to IO_PIN[8]
set_location_assignment PIN_Y16 -to IO_PIN[9]
set_location_assignment PIN_Y17 -to IO_PIN[10]
set_location_assignment PIN_AA17 -to IO_PIN[11]
set_location_assignment PIN_AA18 -to IO_PIN[12]
set_location_assignment PIN_AA19 -to IO_PIN[13]
set_location_assignment PIN_AA20 -to IO_PIN[14]
set_location_assignment PIN_Y19 -to IO_PIN[15]
set_location_assignment PIN_Y20 -to IO_PIN[16]
set_location_assignment PIN_AB20 -to IO_PIN[17]
set_location_assignment PIN_AB21 -to IO_PIN[18]
set_location_assignment PIN_AB22 -to IO_PIN[19]
set_location_assignment PIN_AA22 -to IO_PIN[20]
set_location_assignment PIN_Y22 -to IO_PIN[21]
set_location_assignment PIN_W22 -to IO_PIN[22]
set_location_assignment PIN_W21 -to IO_PIN[23]
set_location_assignment PIN_Y21 -to IO_PIN[24]
set_location_assignment PIN_V21 -to IO_PIN[25]
set_location_assignment PIN_U22 -to IO_PIN[26]
set_location_assignment PIN_W19 -to IO_PIN[27]
set_location_assignment PIN_V20 -to IO_PIN[28]
set_location_assignment PIN_U20 -to IO_PIN[29]
set_location_assignment PIN_U21 -to IO_PIN[30]
set_location_assignment PIN_T22 -to IO_PIN[31]
set_location_assignment PIN_R22 -to IO_PIN[32]
set_location_assignment PIN_R21 -to IO_PIN[33]
set_location_assignment PIN_P22 -to IO_PIN[34]
set_location_assignment PIN_T19 -to IO_PIN[35]
set_location_assignment PIN_T20 -to IO_PIN[36]
set_location_assignment PIN_P17 -to IO_PIN[37]
set_location_assignment PIN_P16 -to IO_PIN[38]
set_location_assignment PIN_N21 -to IO_PIN[39]
set_location_assignment PIN_N20 -to IO_PIN[40]
set_location_assignment PIN_M20 -to IO_PIN[41]
set_location_assignment PIN_M21 -to IO_PIN[42]
set_location_assignment PIN_N19 -to IO_PIN[43]
set_location_assignment PIN_M18 -to IO_PIN[44]
set_location_assignment PIN_L19 -to IO_PIN[45]
set_location_assignment PIN_L18 -to IO_PIN[46]
set_location_assignment PIN_L22 -to IO_PIN[47]
set_location_assignment PIN_M22 -to IO_PIN[48]
#
set_global_assignment -name ENABLE_SIGNALTAP OFF
set_global_assignment -name USE_SIGNALTAP_FILE stp1.stp
set_global_assignment -name ENABLE_OCT_DONE OFF
set_global_assignment -name ENABLE_CONFIGURATION_PINS OFF
set_global_assignment -name ENABLE_BOOT_SEL_PIN OFF
set_global_assignment -name USE_CONFIGURATION_DEVICE OFF
set_global_assignment -name CRC_ERROR_OPEN_DRAIN OFF
set_global_assignment -name RESERVE_FLASH_NCE_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name OUTPUT_IO_TIMING_NEAR_END_VMEAS "HALF VCCIO" -rise
set_global_assignment -name OUTPUT_IO_TIMING_NEAR_END_VMEAS "HALF VCCIO" -fall
set_global_assignment -name OUTPUT_IO_TIMING_FAR_END_VMEAS "HALF SIGNAL SWING" -rise
set_global_assignment -name OUTPUT_IO_TIMING_FAR_END_VMEAS "HALF SIGNAL SWING" -fall
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_DATA1_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_DATA0_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_DCLK_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/Debounce/LongDebounce/debounce.vhd"
set_global_assignment -name VHDL_FILE Components/RAM_16Kx16.vhd
set_global_assignment -name VHDL_FILE Components/RAM_4Kx16.vhd
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/SBCTextDisplayRGB.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/SansBoldRomReduced.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/SansBoldRom.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/DisplayRam2K.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/DisplayRam1K.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/CGABoldRomReduced.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/TERMINAL/CGABoldRom.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/UART/bufferedUART.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/CPU/M68000/TG68K_2013/TG68KdotC_Kernel.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/CPU/M68000/TG68K_2013/TG68K_Pack.vhd"
set_global_assignment -name VHDL_FILE "../../MultiComp (VHDL Template)/Components/CPU/M68000/TG68K_2013/TG68K_ALU.vhd"
set_global_assignment -name VHDL_FILE TS2_68000_Top.vhd
set_global_assignment -name QIP_FILE Components/Monitor_68K_ROM.qip
set_global_assignment -name QIP_FILE Components/RAM_8Kx16.qip
set_global_assignment -name NUM_PARALLEL_PROCESSORS ALL
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top
>/pre>

Resources
* GitHub Repo