Difference between revisions of "XR2206"
Blwikiadmin (talk | contribs) (Created page with "== XR-2206 Board == The XR-2206 board is based on the XR-2206, which is a single IC function generator. The board adds the external parts to make a sine wave generator capabl...") |
Blwikiadmin (talk | contribs) |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | == | + | [[File:XR2206_3D.png]] |
| + | |||
| + | == Features == | ||
The XR-2206 board is based on the XR-2206, which is a single IC function generator. The board adds the external parts to make a sine wave generator capable of being controlled from the High Voltage Digital Pot or the High Voltage Digital Pot 2 board. This allows a microcontroller to digitally set the frequency of the output. | The XR-2206 board is based on the XR-2206, which is a single IC function generator. The board adds the external parts to make a sine wave generator capable of being controlled from the High Voltage Digital Pot or the High Voltage Digital Pot 2 board. This allows a microcontroller to digitally set the frequency of the output. | ||
| Line 5: | Line 7: | ||
=== XR-2206 IC === | === XR-2206 IC === | ||
| − | The XR-2206 | + | The XR-2206 is a monolithic function generator integrated circuit capable of producing high quality sine, square, triangle, ramp, and pulse waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated by an external voltage. Frequency of operation can be selected externally over a range of 0.01Hz to more than 1MHz. |
| + | |||
| + | The Exar XR-2206 is no longer manufactured, but it is widely available on ebay from China. | ||
== Rev X3 Board == | == Rev X3 Board == | ||
| − | This is the third revision of the board | + | * This is the third revision of the board |
| + | * Built onto the [[IntegTheremin]] board | ||
=== Rev X3 Schematic === | === Rev X3 Schematic === | ||
| Line 62: | Line 67: | ||
# Ground | # Ground | ||
# Voltage (+12V) | # Voltage (+12V) | ||
| + | # Sine wave output | ||
| − | |||
J2 is the connection to an external pot. | J2 is the connection to an external pot. | ||
| − | Ground | + | $ Ground |
| − | Resistance | + | # Resistance |
| − | Rev X2 Parts List | + | |
| − | Rev X2 Mounting Holes | + | === Rev X2 Parts List === |
| + | |||
| + | === Rev X2 Mounting Holes === | ||
| + | |||
The board has a single 4-40 mounting hole for either mounting horizontally with standoffs or vertically with an L bracket. | The board has a single 4-40 mounting hole for either mounting horizontally with standoffs or vertically with an L bracket. | ||
| − | Alternatives | + | === Alternatives === |
| + | |||
DDS from an Arduino | DDS from an Arduino | ||
| − | |||
| − | |||
| − | Rev X1 Schematic | + | == Rev X1 Board == |
| − | File:Xr2206-schem-x1.PNG | + | |
| + | [[File:XR-2206-2013-01-04-182208-X1.jpg]] | ||
| + | |||
| + | === Rev X1 Schematic === | ||
| + | |||
| + | [[File:Xr2206-schem-x1.PNG]] | ||
| + | |||
| + | === Rev X1 Board Issues === | ||
| − | + | * VGS silkscreen s/b GVS | |
| − | VGS silkscreen s/b GVS | + | * Resistors are 1/8W leaving this point alone since it's small and I bought 1/8W resistors already |
| − | Resistors are 1/8W leaving this point alone since it's small and I bought 1/8W resistors already | + | * Dropped ground plane from .020 to .012" |
| − | Dropped ground plane from .020 to .012" | + | * Need pin 3 connections. |
| − | Need pin 3 connections. | + | * R1 s/b 10K |
| − | R1 s/b 10K | + | * Changed C1, was 1uF, s/b 0.1uF |
| − | Changed C1, was 1uF, s/b 0.1uF | + | * Pin 3 is missing waveform adjustment resistors |
| − | Pin 3 is missing waveform adjustment resistors | ||
Latest revision as of 15:50, 29 March 2022
Features
The XR-2206 board is based on the XR-2206, which is a single IC function generator. The board adds the external parts to make a sine wave generator capable of being controlled from the High Voltage Digital Pot or the High Voltage Digital Pot 2 board. This allows a microcontroller to digitally set the frequency of the output.
XR-2206 IC
The XR-2206 is a monolithic function generator integrated circuit capable of producing high quality sine, square, triangle, ramp, and pulse waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated by an external voltage. Frequency of operation can be selected externally over a range of 0.01Hz to more than 1MHz.
The Exar XR-2206 is no longer manufactured, but it is widely available on ebay from China.
Rev X3 Board
- This is the third revision of the board
- Built onto the IntegTheremin board
Rev X3 Schematic
Rev X3 Layout
Rev X3 Mounting Holes
The board has three 4-40 mounting holes for either mounting horizontally with standoffs or vertically with an L bracket.
Rev X3 improvements over X2 version
Replaced Waveform adjust fixed resistors with 25K variable resistor (RV1). Split GVS header (J1) into GV and GS headers for separate power (J1) versus outputs (J3). Added a 3rd mounting hole.
Connectors
The connectors are two pin 2.54mm (0.1") pitch headers.
J1 - Power
- +12VDC
- GND
J2 - Pot/Frequency Adjust
- GND
- Adjust
J3 - Output
- VCO Out
- GND
Rev X2 Board
Rev X2 Schematic
Rev X2 Connectors
J1 is Power/signal control circuit connected as GVS (Ground, Voltage (+12V), and signal output).
- Ground
- Voltage (+12V)
- Sine wave output
J2 is the connection to an external pot.
$ Ground
- Resistance
Rev X2 Parts List
Rev X2 Mounting Holes
The board has a single 4-40 mounting hole for either mounting horizontally with standoffs or vertically with an L bracket.
Alternatives
DDS from an Arduino
Rev X1 Board
Rev X1 Schematic
Rev X1 Board Issues
- VGS silkscreen s/b GVS
- Resistors are 1/8W leaving this point alone since it's small and I bought 1/8W resistors already
- Dropped ground plane from .020 to .012"
- Need pin 3 connections.
- R1 s/b 10K
- Changed C1, was 1uF, s/b 0.1uF
- Pin 3 is missing waveform adjustment resistors
