Difference between revisions of "MyMenu Assembly Sheet"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 21: | Line 21: | ||
|- | |- | ||
|4 | |4 | ||
| − | |0/ | + | |0/OPEN (0805) |
|R10,R11,R20,R21 | |R10,R11,R20,R21 | ||
| | | | ||
| Line 33: | Line 33: | ||
| | | | ||
|1 | |1 | ||
| − | | | + | |CONN, 5x1 |
|P2 | |P2 | ||
|- | |- | ||
| Line 41: | Line 41: | ||
| | | | ||
|5 | |5 | ||
| − | | | + | |SW_PUSH, 6mm |
|SW1-SW5 | |SW1-SW5 | ||
|- | |- | ||
| Line 53: | Line 53: | ||
|- | |- | ||
|3 | |3 | ||
| − | |DNP | + | |DNP (0805) |
|R13,R15,R17 | |R13,R15,R17 | ||
| | | | ||
| Line 61: | Line 61: | ||
|- | |- | ||
|} | |} | ||
| + | |||
| + | == OLED Card Power Option == | ||
| + | |||
| + | OLEDS cards have varying power/ground pinouts. Install 0 ohm resistors or leave open resistors to match pinout of OLED card used | ||
| + | |||
| + | === OLED card pin 1 = Vcc case, pin 2 = GND === | ||
| + | |||
| + | * Install R10, R21 = 0 ohms for pin 1 = VCC, pin 2 = GND | ||
| + | * R11, R20 left open | ||
| + | |||
| + | === OLED card pin 1 = GND case for pin 1 = GND, pin 2 = VCC === | ||
| + | |||
| + | * Install R11, R20 = 0 ohms for pin 1 = GND case | ||
| + | * R10, R21 left open | ||
Latest revision as of 18:34, 6 June 2022
Contents
Parts List
| Qty | Value | RefDes | Qty | Value | RefDes | |
|---|---|---|---|---|---|---|
| 3 | 0 (0805) | R14,R16,R18 | 3 | LED (0805) | D1-D3 | |
| 4 | 0/OPEN (0805) | R10,R11,R20,R21 | 2 | CONN_4 | P1,P3 | |
| 6 | 10K (0805) | R6-R9,R12,R19 | 1 | CONN, 5x1 | P2 | |
| 2 | 2.2K (0805) | R1,R2 | 5 | SW_PUSH, 6mm | SW1-SW5 | |
| 3 | 330 (0805) | R3-R5 | 1 | MCP23008SO | U1 | |
| 3 | DNP (0805) | R13,R15,R17 |
OLED Card Power Option
OLEDS cards have varying power/ground pinouts. Install 0 ohm resistors or leave open resistors to match pinout of OLED card used
OLED card pin 1 = Vcc case, pin 2 = GND
- Install R10, R21 = 0 ohms for pin 1 = VCC, pin 2 = GND
- R11, R20 left open
OLED card pin 1 = GND case for pin 1 = GND, pin 2 = VCC
- Install R11, R20 = 0 ohms for pin 1 = GND case
- R10, R21 left open
