Difference between revisions of "ODAS-PSOC5 Rev X1-X4"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 301: | Line 301: | ||
* [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects GitHub Repository] | * [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects GitHub Repository] | ||
| + | |||
| + | == References == | ||
| + | |||
| + | * [https://www.infineon.com/dgdl/Infineon-AN77759_Getting_Started_with_PSoC_5LP-ApplicationNotes-v08_00-EN.pdf?fileId=8ac78c8c7cdc391c017d071b8fb71dc6&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN77759 Getting Started with PSoC 5LP] | ||
| + | * [https://www.infineon.com/dgdl/Infineon-AN61290_PSoC_3_and_PSoC_5LP_Hardware_Design_Considerations-ApplicationNotes-v17_00-EN.pdf?fileId=8ac78c8c7cdc391c017d07254f524a25&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN61290 PSoC 5LP Hardware Design Considerations] | ||
| + | * [https://www.infineon.com/dgdl/Infineon-AN58304_PSoC_3_and_PSoC_5LP_Pin_Selection_for_Analog_Designs-ApplicationNotes-v09_00-EN.pdf?fileId=8ac78c8c7cdc391c017d072e43f252d4&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN58304 PSoC 5LP – Pin Selection for Analog Designs] | ||
| + | * [https://www.infineon.com/dgdl/Infineon-AN81623_PSoC_3_PSoC_4_and_PSoC_5LP_Digital_Design_Best_Practices-ApplicationNotes-v07_00-EN.pdf?fileId=8ac78c8c7cdc391c017d0726b5b94b78&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN81623 PSoC 5LP Digital Design Best Practices] | ||
| + | * [https://www.infineon.com/dgdl/Infineon-AN69133_PSoC_3_PSoC_5LP_Easy_Waveform_Generation_with_the_WaveDAC8_Component-ApplicationNotes-v07_00-EN.pdf?fileId=8ac78c8c7cdc391c017d0730b6d05487 AN69133 PSoC 5LP Easy Waveform Generation with the WaveDAC8 Component] | ||
| + | * [https://www.infineon.com/dgdl/Infineon-CE58035-Code%20Example-v01_00-EN.zip?fileId=8ac78c8c7cdc391c017d0d71d4284c27 I2C EEPROM example] | ||
== Assembly Sheet == | == Assembly Sheet == | ||
[[ODAS-PSOC5 Rev X4 Assembly Sheet]] | [[ODAS-PSOC5 Rev X4 Assembly Sheet]] | ||
Latest revision as of 15:59, 5 September 2022
Contents
Features
- ODAS-PSOC5 - Rev 5+
- PSOC5 Programmable System on a Chip
- Part number: CY8C5267AXI-LP051
- Core: ARM Cortex M3
- Data Bus Width: 32 bit
- Maximum Clock Frequency: 67 MHz
- Program Memory Size: 128 kB
- Data RAM Size: 32 kB
- ADC Resolution: 12 bit
- Data RAM Type: SRAM
- Interface Type: I2C, USB
- Number of ADC Channels: 1
- Number of I/Os: 72 I/O
- Number of Timers/Counters: 4 Timers
- Program Memory Type: Flash
- 16 MHz External Crystal
- Connectors
- USB Connector (USB-B Mini)
- I/O Connector (30 I/O lines which can be analog or digital connections)
- Two voltage zones with 3.3V and 5V selection jumpers
- I2C Connector (4-pin header)
- SPI Connector (6-pin header)
- 24LC024 ODAS Personality EEPROM
- pid = 8
- Write protect jumper
- On Board LED (5.4)
- 9V power input
- On-board 3.3V and 5V regulators
- Fuses on 3.3V and 5V power
- 95x55mm ODAS Form Factor
- Compatible with Land Boards Open Data Acquisition System (ODAS) Cards
- (4) #6 screw holes for solid mounting
PSoC Architecture
Headers
H1 - PSOC Programming Header
- SWDIO
- SWDCLK
- RESET
- GND
H2 - EEPROM Write Enable
- Install to enable EEPROM writes
H3 - I/O Voltage Zone 3 (VZ3)
- 1-2 = 3.3V
- 2-3 = 5V
- Connects to J1 VZ3 pins
H4 - I/O Voltage Zone 0 (VZ0)
- 1-2 = 3.3V
- 2-3 = 5V
- Connects to J1 VZ0 pins
Connectors
J1 - Power
- 7-12V in
- Regulator provides 5V to card
- Fuse protected 5V and 3.3V power distribution
J2 - USB Micro B
- Power not connected through this connector
- USB-Serial connection
P1 - I/O Connector
| Pin | Descr | Pin | Descr | |
|---|---|---|---|---|
| 1 | GND | 2 | GND | |
| 3 | VCC (Zone 0) | 4 | VCC (Zone 0) | |
| 5 | Pin.85 | 6 | Pin.84 | |
| 7 | Pin.83 | 8 | Pin.82 | |
| 9 | Pin.81 | 10 | Pin.80 | |
| 11 | Pin.79 | 12 | Pin.78 | |
| 13 | Pin.77 | 14 | Pin.76 | |
| 15 | Pin.74 | 16 | Pin.73 | |
| 17 | Pin.72 | 18 | Pin.71 | |
| 19 | Pin.70 | 20 | Pin.69 | |
| 21 | Pin.68 | 22 | Pin.67 | |
| 23 | Pin.56 | 24 | Pin.55 | |
| 25 | Pin.54 | 26 | Pin.53 | |
| 27 | Pin.52 | 28 | Pin.51 | |
| 29 | Pin.49 | 30 | Pin.48 | |
| 31 | Pin.47 | 32 | Pin.46 | |
| 33 | Pin.45 | 34 | Pin.44 | |
| 35 | VCC (Zone 3) | 36 | VCC (Zone 3) | |
| 37 | GND | 38 | GND | |
| 39 | N/C | 40 | N/C |
P2 - I2C Master (or Slave)
- GND
- 3.3V
- SDA
- SCL
P3 - I2C Terminator
- Install headers to enable terminators
- 1-2 SDA 3.3K Terminator
- 3-4 SCL 3.3K Terminator
P4 - SPI
- SPI_MOSI
- SPI_MISO
- SPI_CK
- SPI_CE0
- +3.3V
- GND
Programming
- Programmed using KitProg
- KitProg is a part of CY8CKIT-059
- Has a CY8C5868LTI-LP039 used as the programmer
- Fitted with 1x4 right angle header
- VTARG not connected
- Cables
- 4 pin 1:1 Dupont Programming cable
- Plugs into SWD (H1) connector on UUT
- Other end plugs into KitProg J7
- USB A Male to female cable
- 4 pin 1:1 Dupont Programming cable
- CY8CKIT-059 Guide
- KitProg User Manual
- Program using PSOC Creator
- Select Debug, Program
- Select Device/connect
Factory Acceptance Test (FAT)
- Unit Under Test (UUT)
- H3 and H4 set to 5V
- P3 SDA, SCL termination jumpers installed
- H2 EEWR jumper installed
- 9V into the DC power jack
- Uses LED-32 card from Arduino Based Test Station
- Cable set from UUT to LED-32
- Running ODAS-PSOC5-LED-01 Build
- Lights are lit in the following order
- D0 through D14, LED on card, then D30 through D17
- D16 = power (always on)
- D15, D31 are not used
Mechanicals
Software
References
- AN77759 Getting Started with PSoC 5LP
- AN61290 PSoC 5LP Hardware Design Considerations
- AN58304 PSoC 5LP – Pin Selection for Analog Designs
- AN81623 PSoC 5LP Digital Design Best Practices
- AN69133 PSoC 5LP Easy Waveform Generation with the WaveDAC8 Component
- I2C EEPROM example
