6 Channel Relay Driver Card

Features

• Drives QRP Labs Ultimate relay-switched BPF/LPF kit
  • Drives either receiver Band Pass (BP) Filters or transmitter Low Pass (LP) Filters
  • Open collector to turn on/off relay
  • Drives low to turn on relay
    • Other side of relay pulled up to 5V
  • User should only turn on one output at a time
• Inputs
  • 6 channels (5 used with Ultimate Relay Card)
  • Active-high in to drive relay to on state
  • 3.3K to transistor base
    • 1 mA for 3.3V drive
    • 1.5 mA for 5V drive
• Outputs
  • Open Collector outputs from 2N3904 NPN transistors
• Power
  • 9-14V power in
  • 5V power out to power relays
  • DC jack
• 36x37mm card
  • 3 PCBs for $11 from OshPark

Ultimate Relay Card

• Ultimate relay-switched LPF kit
  • Ultimate relay-switched LPF kit Build Instructions
• Takes five QRP Labs Bandpass Filters

Ultimate Relay Card Connections

• The RF input is the RFI pin of the 2 x 5-pin header on the left of the board (same as in the Low Pass Filter kit usage)
• RF output cut the track from the SMA connector center pins and add a wire to connect it to the common bus track that runs horizontally across the board, finishing at the "RF" pad circled in yellow
• Cut/Jumper
  • Cut on top side near Vertical SMA
  • Jumper on rear side

• Jumpers

Ultimate Relay Card Jumpers - Band Pass (BP)

• To switch Band Pass (BP) filters, use the jumper configuration shown below

Ultimate Relay Card Connectors

1. +5V
2. B5
3. B3
4. B4
5. B1
6. B2
7. GND
8. RFIn
9. GND
10. RFOut

Connectors

J1 - Input Connector

1. N/C
2. IN1
3. IN2
4. IN3
5. IN4
6. IN5
7. IN6
8. GND

J2 - Output Connector

1. GND
2. OUT6
3. OUT5
4. OUT4
5. OUT3
6. OUT2
7. OUT1
8. 5V OUT

Power Connector

• 7-14V input
• Center positive

Control via VFO-003

• VFO-003
  • Band select via menu option
• J8 - Arduino P5-P9
• Arduino pins

1. Arduino D5 - 10M select
2. Arduino D6 - 15M select
3. Arduino D7 - 20M select
4. Arduino D8 - 40M select
5. Arduino D9 - 80M select
6. Vcc
7. GND
8. GND

Cables

VFO-003 to Relay Driver Card

RLY_DRVR pin 1x8 BERG	Signal	Function	VFO-003_Pin 1x8 BERG
1	N/C	N/C
2	IN1	10M	1
3	IN2	15M	2
4	IN3	20M	3
5	IN4	40M	4
6	IN5	80M	5
7	IN6	N/C
8	GND	GND	7

Relay Driver to Relay Card

RLY pin 2x5 BERG	Signal	Function	RLY_DRVR pin 1x8 BERG	Signal
1	+5V	Power	8	5V
2	B5	80M	3	OUT5
3	B3	20M	5	OUT3
4	B4	40M	4	OUT4
5	B1	10M	7	OUT1
6	B2	15M	6	OUT2
7	GND	RF Gnd	N/C	GND
8	RFI	RF In	N/C
9	GND	Power	1	GND
10	RFO	N/C	N/C
			2	N/C

Testing

• Apply 9-12V to DC jack
• Use LED w/ resistor on output to check 5V
• One channel at a time
  • Pull up channel input to +5V
  • Check output with LED pulled up to +5V out

CAD