Difference between revisions of "BLACK-PILL-HUB"

From Land Boards Wiki
Jump to navigation Jump to search
Line 10: Line 10:
 
** Independent 3.3V/5V power for each channel
 
** Independent 3.3V/5V power for each channel
 
* Separate interrupts for each channel
 
* Separate interrupts for each channel
* GVS connections for Blue Pill pins
+
* GVS connections for Black Pill pins
 
* Reset switch
 
* Reset switch
  

Revision as of 11:46, 26 January 2021

Black-Pill-Board.png

Features

Black Pill Module

Not pin compatible with Blue Pill due to power pin locations

BlackPillBoard-720px.png

Connectors

J1 - 5V power

  • DC jack
  • 5V
  • Center positive

J4 - 5V Power

  • 5mm terminal block

J7 - I2C

  • The I2C interface that goes to the I2C hub part
  1. SCL (PB6)
  2. SDA (PB7)
  3. 3.3V
  4. GND

P1 - 5V

  • 2x4 header with 5V from H2 (Rev 4 card)

P2 - Vbattery

  • Battery power to the Blue Pill board
  1. GND
  2. Vbat

P3 - FTDI connector (Rev X1-X3)

  • To cable to FTDI wires swap pins 4 and 5 in cable
  • FTDI card jumper has to be set to 3.3V since STM32 has 3.3V signal levels
  1. GND
  2. N/C
  3. VCC (to H8 pin 2)
  4. TX (to Blue Pill RX) (PA10 pin on STM32)
  5. RX (to Blue Pill Tx) (PA9 pin on STM32)
  6. RESET*

FTDI rot.jpg

P3 - FTDI Module (Rev 4 or higher)

  • Cheap FT232 module pinout

FTDI rot.jpg

P4, P5, P6, P7 - I2C Interfaces #0-#3

  1. INT*
  2. SCL
  3. SDA
  4. VCC
  5. GND

P8 - SPI

  1. PA6 (MISO)
  2. 3.3V
  3. PA5 (SCK)
  4. PA7 (MOSI)
  5. RES
  6. GND

P11/P12 - GVS Connector

  • Ground, Power, Signal pins
  1. n/c
  2. PC13
  3. PC14
  4. PC15
  5. PA0
  6. PA1
  7. PA2
  8. PA3
  9. PA4
  10. PA5/SCK1
  11. PA6/MISO1
  12. PA7/MOSI1
  13. PB0
  14. PB1
  15. PB10
  16. PB11

P12/P13 - GVS Connector

  • Ground, Power, Signal pins
  1. n/c
  2. PB9
  3. I2C_INT (PB8)
  4. I2C_SDA1 (PB7)
  5. I2C_SCL (PB6)
  6. PB5
  7. PB4
  8. PB3
  9. PA15
  10. PA12
  11. PA11
  12. RX
  13. TX
  14. PA8
  15. PB15
  16. PB14
  17. PB13
  18. PB12

Headers

H1 - 3.3V (Rev X1-X3)

  • Install to power 3.3V from regulator

H1 - 3.3V source select

  • 1-2 power from 5V to 3.3V regulator
  • 2-3 Power from Blue Pill board 3.3V regulator

H2 - 5V Jumper (Rev X1-X3)

  • Install to connect J4 and J1 5V

H2 - 5V Power Source (Rev 4 or higher)

  • T-shaped header
  • Up - Power 5V from BluePill Hub USB power
  • Left - Power 5V from DC Jack
  • Down - Power 5V from FTDI 5V

H3, H4, H5, H6 - I2C Power

  • Select the power to the I2C interface
  • Install in one of the two positions to power external I2C interface from the board
  • Remove if power comes in from external I2C interface
  1. 3.3V
  2. 5V

H7 - 3.3V from Blue Pill module 3.3V regulator

  • Install = power on-board 3.3V circuitry from regulator on Blue Pill module
    • H8 should not be installed if H7 is installed

H8 - Power from FTDI

  • 1-2 = 3.3V from FTDI (don't ever do this)
  • 2-3 = 5V from FTDI (probably don't do this)
  • H7 should not be installed if H8 is installed

H9 - Hub Chip Address

  • Select the address of the PCA9544A I2C hub

Switches

SW1 - Reset Switch

  • Press to reset Blue Pill board

SW2 - Switch on/off J1, J4 power source

Schematic

Software

Testing

Programming

SerialPropogramming (AN3155).PNG

Assembly Sheet