Difference between revisions of "DRIVE50"

From Land Boards Wiki
Jump to navigation Jump to search
 
(16 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/5075-ohm-ttl-line-driver/]]
 +
 
[[file:DRIVE50_P1080480-720PX.jpg]]
 
[[file:DRIVE50_P1080480-720PX.jpg]]
  
Line 19: Line 21:
 
*** Symmetric high-low drive levels
 
*** Symmetric high-low drive levels
 
** Short-circuit proof
 
** Short-circuit proof
*** 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA
+
*** 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA)
* Card input has single buffer stage
+
*** 0.125 W resistor (5V output through 249 ohm resistor with output shorted to ground is 0.1 W)
 +
*** 3.3V, 250 Ohms to ground is 13.2 mA (pins are rated for 24 mA)
 +
*** 0.125 W resistor (3.3V output through 249 ohm resistor with output shorted to ground is 0.044 W)
 +
* Card has input buffer stage
 
* Schmitt Trigger Input
 
* Schmitt Trigger Input
 
* 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
 
* 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
Line 43: Line 48:
 
==== Setup ====
 
==== Setup ====
  
* [[QTPy49]]
+
* [[QTPy49]] or [[QTPy49-01]] card
* [[QT_Py_(RP2040_based)]]
+
* [[QT Py (RP2040_based)]] card
 
** Analog cable  
 
** Analog cable  
 
** GVS Cable to A1
 
** GVS Cable to A1
 
** Analog in (BNC) to A0 on [[QTPy49]]
 
** Analog in (BNC) to A0 on [[QTPy49]]
* [[MyMenu]]
+
* [[MyMenu]] card
 
* Power card options
 
* Power card options
** Connect USB-C to the [[QT_Py_(RP2040_based)]] or  
+
** Connect USB-C to the [[QT Py (RP2040 based)]] or  
 
** Power from 9-12V to DC jack
 
** Power from 9-12V to DC jack
* Cables
 
** USB-C (power option)
 
** Power cable to UUT
 
 
* Terminator - dependent on build option
 
* Terminator - dependent on build option
 
** 50 Ohms
 
** 50 Ohms
 
** 75 Ohms
 
** 75 Ohms
 
* Unit Under Test (UUT)
 
* Unit Under Test (UUT)
* [https://github.com/land-boards/QT-Py/blob/main/CircuitPython/lbcards/PulseGen/PulseGen_DRIVE50_Test.py PulseGen_DRIVE50_Test.py] - Test software for PulseGen and DRIVE50 cards
+
* [https://github.com/land-boards/QT-Py/blob/main/CircuitPython/lbcards/PulseGen/PulseGen_DRIVE50_Test.py PulseGen_DRIVE50_Test.py]
** Stored as code.py on [[QT_Py_(RP2040_based)]] to auto-run
+
** Test software for [[PulseGen]] and DRIVE50 cards
 +
*** Auto-detects card type
 +
** Stored as code.py on [[QT Py (RP2040 based)]] to auto-run
  
 
==== Procedure ====
 
==== Procedure ====
Line 79: Line 83:
  
 
* All 3 LEDs are on
 
* All 3 LEDs are on
 +
 +
== Application Example ==
 +
 +
=== GPS Frequency Standard ===
 +
 +
[[file:GPS_Freq_Std_P18490-720px.jpg]]
 +
 +
* [[GPS_Frequency_Standard|GPS Frequency Standard]]
 +
* Card takes in PPS signal out of GPS module and drives 50 Ohm, 10 MHz Frequency Standard output on coax via BNC connector
  
 
== Mechanicals ==
 
== Mechanicals ==

Latest revision as of 11:25, 20 August 2022

Tindie-mediums.png

DRIVE50 P1080480-720PX.jpg

50 Ohm Driver Card

  • "TTL" Level Line driver
  • 50 or 75 Ohm output impedance
  • BNC or SMA output connector
  • 10K pull-up on input
  • Card is non-inverting
  • 1.5V-5.5V power
    • Typically 3.3V or 5V
  • 3-pin right angle 0.1" pitch input connector
  • (4) 4-40 mounting holes

Driver

  • 5x paralleled 74AC14 drivers
    • 24mA per pin max current output
      • Symmetric high-low drive levels
    • Short-circuit proof
      • 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA)
      • 0.125 W resistor (5V output through 249 ohm resistor with output shorted to ground is 0.1 W)
      • 3.3V, 250 Ohms to ground is 13.2 mA (pins are rated for 24 mA)
      • 0.125 W resistor (3.3V output through 249 ohm resistor with output shorted to ground is 0.044 W)
  • Card has input buffer stage
  • Schmitt Trigger Input
  • 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
    • Normal output = 10 mA per pin

Test

  • Manual or Automated test methods

Manual Test Method

  • Supply Vcc 3.3V to 5V and ground
  • Input is pulled up to Vcc
  • Measure output with BNC T
    • Should be 1/2 of Vcc with 50 Ohm terminator
    • Should be Vcc without terminator

Automated Test Software Method

DRIVE50 P1080485-720PX.jpg

Setup

Procedure

  • Connect 3 pin power cable to card
  • Connect BNC T to output of card
  • Connect BNC female from tester to BNC T male
  • Install 50 terminator to other side of BNC T
  • Connect USB C cable
  • Display will show
PulseGen/DRIVE50 V1.1
50 Ohm card
Set/Got Low
Term High = OK
  • All 3 LEDs are on

Application Example

GPS Frequency Standard

GPS Freq Std P18490-720px.jpg

  • GPS Frequency Standard
  • Card takes in PPS signal out of GPS module and drives 50 Ohm, 10 MHz Frequency Standard output on coax via BNC connector

Mechanicals

DRIVE50 MECHS REV1.PNG

Assembly Sheet