Difference between revisions of "Multicomp in a Box"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
|||
(7 intermediate revisions by the same user not shown) | |||
Line 12: | Line 12: | ||
** Z80 | ** Z80 | ||
*** CP/M (various builds) | *** CP/M (various builds) | ||
+ | * 68000 | ||
+ | ** Teeside 2 compatible | ||
== Enclosure == | == Enclosure == | ||
Line 24: | Line 26: | ||
* [[QM Tech Cyclone V FPGA Board]] | * [[QM Tech Cyclone V FPGA Board]] | ||
* [[SD CARD X49]] | * [[SD CARD X49]] | ||
+ | * [[SWLEDX8|Slide switches card]] - Using 4 slide switches | ||
+ | * [[DB25-02]] - DB-25 | ||
* [[PD01|Power Distribution card]] | * [[PD01|Power Distribution card]] | ||
− | * | + | * Reset switch |
+ | ** Mounted to front panel | ||
+ | ** On FPGA Pin_N16 (J3-6) | ||
* [https://www.ebay.com/sch/i.html?_odkw=usb+blaster&_sop=15&LH_BIN=1&LH_FS=1&_osacat=0&_from=R40&_trksid=p2045573.m570.l1311.R2.TR6.TRC1.A0.H1.TRS1&_nkw=usb+blaster+altera&_sacat=0 USB Blaster] - Remove from case - Opening in enclosure to access USB connector | * [https://www.ebay.com/sch/i.html?_odkw=usb+blaster&_sop=15&LH_BIN=1&LH_FS=1&_osacat=0&_from=R40&_trksid=p2045573.m570.l1311.R2.TR6.TRC1.A0.H1.TRS1&_nkw=usb+blaster+altera&_sacat=0 USB Blaster] - Remove from case - Opening in enclosure to access USB connector | ||
Line 51: | Line 57: | ||
* 5V Power comes from the USB | * 5V Power comes from the USB | ||
* 3.3V regulator on the [[RETRO-EP4CE15]] Card | * 3.3V regulator on the [[RETRO-EP4CE15]] Card | ||
+ | ** H2 pins 2-3 shorted on the [[RETRO-EP4CE15]] card | ||
+ | ** Set to route 3.3V to the I/O connector | ||
== Cabling == | == Cabling == |
Revision as of 07:36, 16 February 2022
Contents
Features
- Multicomp - FPGA retrocomputers
- 6502
- OSI BASIC
- UK101 / OSI C1P
- 6800
- MIKBUG
- 6809
- BASIC
- Beal Crook Multiple OS
- Z80
- CP/M (various builds)
- 6502
- 68000
- Teeside 2 compatible
Enclosure
Card Set
- RETRO-EP4CE15 FPGA Baseboard
- QM Tech Cyclone V FPGA Board
- SD CARD X49
- Slide switches card - Using 4 slide switches
- DB25-02 - DB-25
- Power Distribution card
- Reset switch
- Mounted to front panel
- On FPGA Pin_N16 (J3-6)
- USB Blaster - Remove from case - Opening in enclosure to access USB connector
QM Tech Cyclone V FPGA Board Features
- QM Tech Cyclone V FPGA Board
- QMTECH Altera Intel FPGA Core Board Cyclone V CycloneV 5CEFA2F23 SDRAM
- QMTECH GitHub page
- On-Board FPGA: 5CEFA2F23I7N
- On-Board FPGA external crystal frequency: 50MHz
- 5CEFA2F23 has rich RAM resource up to 1,760Kb
- 5CEFA2F23 has 25K logic cells
- On-Board Micron MT25QL128A SPI Flash, 16M bytes for user configuration code
- On-Board Winbond 32MB SDRAM, W9825G6KH-6
- On-Board 3.3V power supply for FPGA by using MP2315 wide input range DC/DC
- 5CEFA2F23 core board has two 64p, 2.54mm pitch headers for extending 108 user IOs. All 108 user IOs are precisely designed with length matching
- 5CEFA2F23 core board has 3 user switches
- 5CEFA2F23 core board has 2 user LEDs
- 5CEFA2F23 core board has JTAG interface, by using 10p, 2.54mm pitch header
- 5CEFA2F23 core board PCB size is: 6.7cm x 8.4cm
- Default power source for board is: 1A@5V DC, the DC header type: DC-050, 5.5mmx2.1mm
Power
- 5V Power comes from the USB
- 3.3V regulator on the RETRO-EP4CE15 Card
- H2 pins 2-3 shorted on the RETRO-EP4CE15 card
- Set to route 3.3V to the I/O connector
Cabling
SD Card
- SD Card
- Install J3 on SD Card
- Runs card off 3.3V
J1 PIN | SIGNAL | COLOR | SD PIN | FPGA Pin | DIR |
---|---|---|---|---|---|
2 | 3.3V | ORG | 7 | VREG 3.3V | OUT (PWR) |
45 | sdSCLK | GRY | 3 | L19 | OUT |
46 | sdMISO | BLU | 2 | L18 | IN |
47 | sdMOSI | WHT | 4 | L22 | OUT |
48 | sdCS | VIO | 5 | M22 | OUT |
49 | GND | GRN | 1 | GND | OUT (PWR) |