Difference between pages "WA3TFS SDR Upverter Design" and "AudioAmp380"
(Difference between pages)
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) (→Build) |
Blwikiadmin (talk | contribs) |
||
Line 1: | Line 1: | ||
− | [[ | + | [[FILE:AudioAmp380-3D.png]] |
− | == | + | == Design == |
− | + | * Pre-amp plus power amp | |
+ | * 50 Ohm input impedance | ||
+ | * External mount gain potentiometer | ||
+ | ** Gain potentiometer on preamp | ||
+ | * [https://www.ti.com/lit/ds/symlink/lm380.pdf LM380] 2.5W Audio Power Amplifier | ||
+ | ** Wide Supply Voltage Range: 10V-22V | ||
+ | ** Low Quiescent Power Drain: 0.13W (VS= 18V) | ||
+ | ** Voltage Gain Fixed at 50 (34 dB) | ||
+ | ** High Peak Current Capability: 1.3A | ||
+ | ** Input Referenced to GND | ||
+ | ** High Input Impedance: 150kΩ | ||
+ | ** Low Distortion | ||
+ | ** Quiescent Output Voltage is at One-Half of the Supply Voltage | ||
+ | * [https://www.ti.com/lit/ds/symlink/ne5534.pdf NE5534] Pre-amplifier | ||
+ | ** Low-Noise Operational Amplifiers | ||
+ | ** Equivalent Input Noise Voltage 3.5 nV/√Hz Typ | ||
+ | ** Unity-Gain Bandwidth 10 MHz Typ | ||
+ | ** Common-Mode Rejection Ratio 100 dB Typ | ||
+ | ** Wide Supply-Voltage Range ±3 V to ±20 V | ||
+ | ** Used as single supply | ||
+ | * Fits into 80x50x20mm extruded aluminum enclosure | ||
+ | ` | ||
− | + | == Rev 2 Schematic == | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | [[file:AudioAmp380-Schematic.png]] | |
− | + | == Rev 1 Rework == | |
− | + | * Issues | |
+ | ** Front end opamp has + and - reversed | ||
+ | ** Also hooked up the feedback to the wrong input | ||
+ | * 5 Cuts | ||
+ | ** 4 on front | ||
+ | ** 1 on back | ||
+ | * 5 Jumpers on back | ||
− | + | [[file:U2-2_3_Rev1_Rev2_Cuts_Jumpers.png]] | |
− | |||
− | |||
− | == | + | == Videos == |
− | + | [[file:ZL2CTM_Schematic.PNG]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | [[file: | ||
− | = | + | <video type="youtube">GlT0HbvcmrM</video> |
− | + | == Assembly Sheet == | |
− | + | [[LM380 Rev 1 Assembly Sheet]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | [[ | ||
− | |||
− | |||
− | |||
− |
Revision as of 14:10, 15 October 2021
Design
- Pre-amp plus power amp
- 50 Ohm input impedance
- External mount gain potentiometer
- Gain potentiometer on preamp
- LM380 2.5W Audio Power Amplifier
- Wide Supply Voltage Range: 10V-22V
- Low Quiescent Power Drain: 0.13W (VS= 18V)
- Voltage Gain Fixed at 50 (34 dB)
- High Peak Current Capability: 1.3A
- Input Referenced to GND
- High Input Impedance: 150kΩ
- Low Distortion
- Quiescent Output Voltage is at One-Half of the Supply Voltage
- NE5534 Pre-amplifier
- Low-Noise Operational Amplifiers
- Equivalent Input Noise Voltage 3.5 nV/√Hz Typ
- Unity-Gain Bandwidth 10 MHz Typ
- Common-Mode Rejection Ratio 100 dB Typ
- Wide Supply-Voltage Range ±3 V to ±20 V
- Used as single supply
- Fits into 80x50x20mm extruded aluminum enclosure
`
Rev 2 Schematic
Rev 1 Rework
- Issues
- Front end opamp has + and - reversed
- Also hooked up the feedback to the wrong input
- 5 Cuts
- 4 on front
- 1 on back
- 5 Jumpers on back
Videos