RF-Amp

From Land Boards Wiki
Jump to navigation Jump to search

RF-Amp Front.png

RF Amplifier Features

RF Amplifier Design

Schematic

RF Amp Schematic-4.PNG

LT Spice Simulation

RF-AMP-LTSPICE XFMRS.PNG

Charlie Morris Design

Beta DC

  • Geometric mean min/max beta at operating current
    • =sqrt(100*300) = 173

Beta AC

  • Gain bandwidth product divided by operating frequency
    • Assume operating frequency of 10 MHz (my IF is actually at 9 MHz)
    • = 300/10 = 30

DC Operating Point

  • CE current 10 mA
    • If Vce = 6V, this is 60 mW power dissipation
  • Assume Ve (voltage across emitter resistor) = 1/10 Vcc = 12V/10 = 1.2V
      • R3 is Re (emitter resistor) = 1.2V/0.01A = 120 ohms
  • VCE = 0.7V (typical from data sheet)
  • V(emitter) = 1.2V
  • V(base) = V(emitter) + VCE = 1.9V
  • Assume current in biasing resistors = 10x current needed by DC beta
    • 10 mA in C-E, beta DC less = 10 mA/173 = 48 uA
    • 10x the current in the biasing resistors = 480 uA (calculated)
  • R2 is 1.9V at 480 uA = 3.9K use 3.3K
    • Actual current will be 1.9V/3.3 ohms = 634 mA
  • R1 sources current to R2 and transistor base
    • Voltage = Vcc (12V) - 1.9V = 10.1V
    • Current = 576 uA + 57 uA = 634 uA
    • R1 = 10.1 / .634 mA = 15.9K, use 15k

Input resistance

  • Xc for 0.1uF cap from emitter to ground
    • C=0.1uF
    • F=10MHz
    • 1/2*pi*F*C = 0.16 ohms
  • Parallel resistors R1, R2 paralleled with transistor input impedance
    • R1=15K, R2=3.3K
    • Transistor resistance = Beta AC (30) times re
      • re = 26 / Ie (10 mA in mA) = 26/10 = 2.6
      • Beta AC * re = 30*2.6 = 78 ohms - predominates
    • All in parallel are 75.8 ohms

Input/Output Transformers

FT37-43 10 Turns.PNG

Tracks

RF-Amp-tracks.PNG

Input Transformer

  • Input Transformer (T1 on Charlie's - T2 on this board)
  • 50:75.8 Ohms = 1 : 1.23 turns ratio
  • n = sqrt(Zout/Zin) = sqrt(75.8/50) = 1.23
    • 9:11 = 1:1.22 (close enough)
    • 9 turns primary
      • 9 turns on FT37-43 = 38.3 uH
    • 11 turns on secondary
      • 11 turns on FT37-43 = 42.4 uH
    • 20 turns = 12 in

RF-Amp-T2.PNG

Output Transformer

  • Output transformer (T2 on Charlie's - T1 on this board)
  • T2 - different than Charlie's design since my Crystal filters are all 50 ohms in/out
  • 200:50 ohms
  • n = sqrt(200/50) = 2:1
  • 10:5 turns
    • 10 turns primary (on transistor collector)
      • 10 turns = 35 uH
    • 5 turns secondary (towards output)
      • 5 turns = 8.75 uH
  • 8 15 turns = 9.5 in

RF-Amp-T1.PNG

Charlie's Notes

IF Amp 0046A.jpg

IF Amp 0046B.jpg

IF Amp 0046C.jpg

IF Amp 0047A.jpg

IF Amp 0047B.jpg

IF Amp 0047C.jpg

NanoVNA Measurements

  • NanoVNA running NanoSaver software on PC
  • Put 40 dB attenuator on wrong side, should be from NanoVNA output into RF-Amp card input
  • Compression on lower frequencies
  • Set external attenuator to 40 dB using RF Attenuators
  • DC current = 12 mA
  • At 9 MHz IF Frequency
    • S21 Gain = +22.4 dBm
    • VSWR = 1.64
    • Input impedance = 76.6-j13 ohms
  • S21 = +20 dBm at 15.5 MHz

RF-Amp Data 2021 1-30MHz.png

RF-Amp S21 2021 1-30MHz.png

RF-Amp VSWR 2021 1-30MHz.png

Tweeks to design

  • Moved 40 dB attenuator to right side, should be from NanoVNA output into RF-Amp card input
  • Compressing/expanding output transformer doesn't change result much
  • Compressing/expanding input transformer changes VSWR resonant frequency and S21 quite a bit
  • Input isn't close enough to 50 Ohms
    • Adjust input transformer ratio?
  • Removed 2 windings on input to reduce input impedance
  • Very good results
  • Return loss > -45 dB from 1-30 MHz

RF-Amp S21 2021 1-30MHz 7to11Turns.png

RF-Amp VSWR 2021 1-30MHz 7to11Turns.png

RF-Amp Data 2021 1-30MHz 7to11Turns.png

Video

Assembly Sheet