Difference between revisions of "RPI-CONSOLE-U"

From Land Boards Wiki
Jump to navigation Jump to search
Line 17: Line 17:
 
* Transmit/receive LEDs
 
* Transmit/receive LEDs
 
* 26-pin connector works with Model A and Model B Pis
 
* 26-pin connector works with Model A and Model B Pis
 +
 +
== Options ==
 +
 +
Extended 26-pin Connector
 +
From RPI-CONSOLE page
 +
 +
RP-Console-CCA-X1-4959-Ext26-640px.jpg
 +
 +
Extended 40-pin Connector
 +
From RPI-CONSOLE page
 +
 +
RP-Console-CCA-X1-4955-Ext40-640px.jpg
 +
 +
Low profile 26-pin Connector
 +
RPI-CONSOLE-U-MTD-PI-ORTHO-X1 6013-640PX.jpg
 +
 +
== Driver ==
 +
 +
Windows Driver setup
 +
 +
Prototype Qualification Tests
 +
Qualification Testing
 +
 +
== Factory Acceptance Tests =
 +
 +
Test Station design
 +
 +
RPI-Console-Test-5459-cropped-640px.jpg
 +
 +
Test Procedure
 +
Test setup as above
 +
Test setup powered down
 +
Install UUT (RPI-Console card being tested)
 +
Disconnect USB cable to Arduino (not used for power)
 +
Install P1 jumper on UUT (power the test station from the RPI-CONSOLE)
 +
Connect USB cable from Test Computer (laptop) to UUT
 +
Boards should power up
 +
Run putty on Test Computer (laptop)
 +
Look in Device manager to make sure COM port was added
 +
Select COM port in putty
 +
Hit reset on Arduino Shield or attached to GVSDuino
 +
Verify the message comes back
 +
The quick brown fox jumped over the lazy dog
 +
0123456789
 +
asdfghjkl
 +
Hit keys to test
 +
Type and verify that the character comes back
 +
Disconnect USB to RPI-Console
 +
Specs
 +
26-pin stacking connector
 +
40-pin stacking connector
 +
External links
 +
Adafruit tutorial
 +
NOOBS without a display
 +
How COM Ports Are Allocated On Driver Installation
 +
Assembly Sheet
 +
RPI-CONSOLE Assembly Sheet
 +
Rev X3 (vs X2)
 +
Moved "Power Pi from USB" connector to center of card
 +
Rev X2 (vs X1)
 +
Moved connector slightly closer to the edge
 +
Made USB connector PWB pads longer
 +
Rev X1 Checkout
 +
Micro USB mounting holes fit well
 +
Connector could be slightly farther to the edge
 +
USB connector PWB pads were too short - trimmed pins to fit
 +
Ordered 3 more from OshPark new X2 rev
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
  
 
* [[RPI-CONSOLE-U Assembly Sheet]]
 
* [[RPI-CONSOLE-U Assembly Sheet]]

Revision as of 13:02, 24 January 2020

Tindie-mediums.png

RPI-CONSOLE-U-MTD-PI-ORTHO-X1 6013-640PX.jpg

Features

  • Console port lets you talk to your Raspberry Pi over USB without a keyboard/mouse/monitor or Ethernet connection.
    • 115200 baud
  • USB Micro-B connector
  • Real FTDi FT230XS
  • Jumper selectable - power the Pi from your computer's USB port.
    • Some nwere Pi cards may take too much power
  • Transmit/receive LEDs
  • 26-pin connector works with Model A and Model B Pis

Options

Extended 26-pin Connector From RPI-CONSOLE page

RP-Console-CCA-X1-4959-Ext26-640px.jpg

Extended 40-pin Connector From RPI-CONSOLE page

RP-Console-CCA-X1-4955-Ext40-640px.jpg

Low profile 26-pin Connector RPI-CONSOLE-U-MTD-PI-ORTHO-X1 6013-640PX.jpg

Driver

Windows Driver setup

Prototype Qualification Tests Qualification Testing

= Factory Acceptance Tests

Test Station design

RPI-Console-Test-5459-cropped-640px.jpg

Test Procedure Test setup as above Test setup powered down Install UUT (RPI-Console card being tested) Disconnect USB cable to Arduino (not used for power) Install P1 jumper on UUT (power the test station from the RPI-CONSOLE) Connect USB cable from Test Computer (laptop) to UUT Boards should power up Run putty on Test Computer (laptop) Look in Device manager to make sure COM port was added Select COM port in putty Hit reset on Arduino Shield or attached to GVSDuino Verify the message comes back The quick brown fox jumped over the lazy dog 0123456789 asdfghjkl Hit keys to test Type and verify that the character comes back Disconnect USB to RPI-Console Specs 26-pin stacking connector 40-pin stacking connector External links Adafruit tutorial NOOBS without a display How COM Ports Are Allocated On Driver Installation Assembly Sheet RPI-CONSOLE Assembly Sheet Rev X3 (vs X2) Moved "Power Pi from USB" connector to center of card Rev X2 (vs X1) Moved connector slightly closer to the edge Made USB connector PWB pads longer Rev X1 Checkout Micro USB mounting holes fit well Connector could be slightly farther to the edge USB connector PWB pads were too short - trimmed pins to fit Ordered 3 more from OshPark new X2 rev

Assembly Sheet