Difference between revisions of "STM32"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 32: | Line 32: | ||
Can't be used on [[BLUE-PILL-HUB]] card without modifications | Can't be used on [[BLUE-PILL-HUB]] card without modifications | ||
| − | * | + | * STM32F401CCU6 or STM32F411CCU6 |
| − | ** 100 MHz | + | ** 84/100 MHz |
** 512 KB Flash (most have 128KB) | ** 512 KB Flash (most have 128KB) | ||
** 128 KB SRAM | ** 128 KB SRAM | ||
| Line 41: | Line 41: | ||
** SPI, I2C, UART interfaces | ** SPI, I2C, UART interfaces | ||
** 7 timers | ** 7 timers | ||
| + | * I2C EEPROM footprint | ||
* USB-C | * USB-C | ||
* Reset button | * Reset button | ||
| Line 46: | Line 47: | ||
* PC 13 LED | * PC 13 LED | ||
* SWD connector | * SWD connector | ||
| − | + | ||
| + | '''Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.''' | ||
| + | |||
[[File:BlackPillBoard-720px.png]] | [[File:BlackPillBoard-720px.png]] | ||
Revision as of 15:04, 2 October 2020
Contents
Blue Pill Board Features
Used on BLUE-PILL-HUB card
- STM32F103
- 72 MHz
- 64KB Flash (most have 128KB)
- 20 KB SRAM
- 3.3V regulator
- 16 MHz
- 1 of x12-bit, A/D converter
- 7-channel DMA controller
- SPI, I2C, UART interfaces
- 7 timers
- MicroUSB
- Reset button
- Download jumper
- Replaced with a slide switch
- Power LED
- PC 13 LED
- SWD connector
- RTC crystal
Black Pill Board Features
Not pin compatible with Blue Pill due to power pin locations
Can't be used on BLUE-PILL-HUB card without modifications
- STM32F401CCU6 or STM32F411CCU6
- 84/100 MHz
- 512 KB Flash (most have 128KB)
- 128 KB SRAM
- 3.3V regulator
- 2x12-bit, A/D converter
- 7-channel DMA controller
- SPI, I2C, UART interfaces
- 7 timers
- I2C EEPROM footprint
- USB-C
- Reset button
- Power LED
- PC 13 LED
- SWD connector
Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.
- WeAct Black Pill V1.2 - Helpful page
Blue Pill vs Black Pill Pinout
Arduino IDE
- Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards
- Arduino Alternative - STM32 Blue Pill Programming Via USB
Uploading Code
- FTDI connection to Blue Pill Hub FTDI connector
- FTDI TX (to Blue Pill RX) (PA10 pin on STM32)
- FTDI RX (to Blue Pill Tx) (PA9 pin on STM32)
- Set Switch (or jumper) on Blue Pill module set towards center of card to upload card to board
- In Arduino IDE,
- Tools
- Board "Generic..."
- Upload method: "Serial..."
- Port: [the comm port]
- Tools
- Upload code
- Takes a while
- Set Switch (or jumper) on Blue Pill module set towards edge of card to run
- Press reset button
Annotated
Mechanicals
Blue Pill Card Schematic
Boot Jumpers
