Difference between revisions of "FTDI-49MM"

From Land Boards Wiki
Jump to navigation Jump to search
Line 53: Line 53:
 
# RX (in)
 
# RX (in)
 
# RTS* (out)
 
# RTS* (out)
 +
 +
== Card Test ==
 +
 +
[[File:OPTOUSB_Tester_Card-Annotated-720pxV.jpg]]
 +
 +
* UUT
 +
* Does not require 5V  or 3.3V Power Supply (used for [[OPTOUSB]] card)
 +
* Test card
 +
* Run puTTY
 +
** Baud rate = 115,200 baud
 +
** Hardware handshake RTS/CTS
 +
* Jumper Settings - Normal operation
 +
** Left jumper in right position (loopback data)
 +
** Middle jumper in left position (handshake = active/ground)
 +
** Right jumper in right position (loopback handshake)
 +
** Type on keyboard and verify it returns data
 +
* Jumper settings - Test Tx/Rx isolation
 +
** Move left jumper to left position
 +
** Type data nothing should come back (verify LED)
 +
** Move left jumper to right position
 +
* Jumper settings - Test RTS/CTS
 +
** Move right jumper to left position (handshake controlled by middle jumper)
 +
** Type and characters should return
 +
** Move middle jumper to to right position (hardware handshake off)
 +
** Type and nothing should go through
 +
** Move middle jumper to to left position (hardware handshake on)
 +
** Characters that were buffered should come in at once
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
  
 
[[FTDI-49MM Assembly Sheet]]
 
[[FTDI-49MM Assembly Sheet]]

Revision as of 15:07, 14 May 2021

Tindie-mediums.png

FTDI-P1746-CROPPED-720PX.jpg

Features

  • FT230X USB-to-FTDI Serial IC
  • USB B connector (not micro or mini, but the beefy USB B connector)
  • FTDI compatible pinout
  • 3.3V or 5V selection jumper
  • Header for 5V power distribution
  • Rx and Tx LEDs
  • (4) 4-40 mounting holes
    • Mounts to 95mm to 45mm adapter
    • Stacks up with standoffs for use with other 95mm cards

Headers/Jumpers

5V/3.3V Jumper

  • Select 5V or 3.3V signal levels on FTDI connector
  • 5V out on FTDI connector VCC pin

FDTI Connector

  1. GND
  2. CTSn
  3. VCC
  4. TX
  5. RX
  6. RTSn

USB Connector

  • USB B Connector

Stackup with EP2 FPGA card

  • Top to bottom of stackup
  1. EP2C5-DB
  2. Cyclone_II_EP2C5_Mini_Dev_Board Card
  3. FTDI-49MM - (this card)
  4. CARRIER95TO49MM

P1752-CROPPED-720PX.jpg

Pinout

  1. GND
  2. CTS* (in)
  3. VCC
  4. TX (out)
  5. RX (in)
  6. RTS* (out)

Card Test

OPTOUSB Tester Card-Annotated-720pxV.jpg

  • UUT
  • Does not require 5V or 3.3V Power Supply (used for OPTOUSB card)
  • Test card
  • Run puTTY
    • Baud rate = 115,200 baud
    • Hardware handshake RTS/CTS
  • Jumper Settings - Normal operation
    • Left jumper in right position (loopback data)
    • Middle jumper in left position (handshake = active/ground)
    • Right jumper in right position (loopback handshake)
    • Type on keyboard and verify it returns data
  • Jumper settings - Test Tx/Rx isolation
    • Move left jumper to left position
    • Type data nothing should come back (verify LED)
    • Move left jumper to right position
  • Jumper settings - Test RTS/CTS
    • Move right jumper to left position (handshake controlled by middle jumper)
    • Type and characters should return
    • Move middle jumper to to right position (hardware handshake off)
    • Type and nothing should go through
    • Move middle jumper to to left position (hardware handshake on)
    • Characters that were buffered should come in at once

Assembly Sheet

FTDI-49MM Assembly Sheet