Difference between revisions of "LB-65CXX-01"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) (→Rev 1) |
Blwikiadmin (talk | contribs) (→Rev 1) |
||
Line 122: | Line 122: | ||
== Checkout == | == Checkout == | ||
− | == Rev 1 == | + | === Rev 1 ================= |
* Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816 | * Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816 | ||
− | * | + | * IF WDC 65C02 or WDC 65C816 is used, pullup U1-36 BE input |
** NC in other CPUs | ** NC in other CPUs | ||
Revision as of 19:48, 19 August 2024
Contents
Features
- 65C02 or 65C816 CPU
- 2 MHz (typical) Oscillator on card
- Reset switch/power monitor
- Address decoder PLD drives RAM/ROM/IO chip selects
- 100x50mm card
Design
Memory Map
0x0000-0x7FFF - 32KB SRAM 0x8000-0x8FFF - 4KB I/O space 0x9000-0xBFFF - 12 KB SRAM (Using 128KB SRAM) 0xC000-0xFFFF - 16KB EPROM space
CPU
- 65C02 or 65C816 CPU
- 2 MHz
- Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816
R65C02 vs W65C02 CPUs
R65C02 vs W65C02 pin differences
- Pin 1
- R65C02 = VSS J2:1-2
- W65C02 = VPB J2:2-3 - Vector Pull
- Pin 5
- R65C02 = NC
- W65C02 = MLB - Memory Lock
- Pin 36
- R65C02 = NC
- W65C02 = BE - Bus Enable
Oscillator
PLD
PLD Listing
Name LB-65CXX-01_PLD; Partno ATF16V8B; Date 08/18/24; Revision 01; Designer DOUG G; Company LAND BOARDS LLC; Assembly LB65CXX01_U2; Location Rustbelt, US; Device G16V8; /* 65C816 Control */ /* Control inputs */ PIN 1 = CLK; PIN 2 = CPUA12; PIN 3 = CPUA13; PIN 4 = CPUA14; PIN 5 = CPUA15; PIN 6 = CPUREAD; PIN 8 = VPA; PIN 9 = VDA; /* Counter data inputs */ PIN 13 = !IOCS; PIN 14 = !ROMCS; PIN 15 = !MEMRD; PIN 16 = !RAMCS; PIN 18 = RDY; RAMCS = !CPUA15 & VDA /* 0x0000-0x7FFF (32KB/64KB SRAM) */ # CPUA15 & !CPUA14 & !CPUA13 & CPUA12 & VDA /* 0x9000-0x9FFF (128KB SRAM) */ # CPUA15 & !CPUA14 & CPUA13 & VDA; /* 0xA000-0xBFFF (128KB SRAM) */ IOCS = CPUA15 & !CPUA14 & !CPUA13 & !CPUA12 & VDA; /* 0x8000-0x8FFF (4KB space) */ ROMCS = CPUA15 & CPUA14 & CPUREAD & VDA; /* 0xC000-0xFFFF (16KB space) */ MEMRD = CPUREAD & VDA; /* RDY = VPA # VDA; */
Reset Controller
- DS1813-5 Reset Controller
- 5V Power Monitor
- Reset controller
- Reset pushbutton to ground
Backplane connector
Mechanicals
Checkout
Rev 1 ==============
- Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816
- IF WDC 65C02 or WDC 65C816 is used, pullup U1-36 BE input
- NC in other CPUs