LB-65CXX-01

Features

• 65C02 or 65C816 CPU
• 2 MHz (typical) Oscillator on card
• Reset switch/power monitor
• Address decoder PLD drives RAM/ROM/IO chip selects
• 100x50mm card

Design

Memory Map

0x0000-0x7FFF - 32KB SRAM
0x8000-0x8FFF - 4KB I/O space
0x9000-0xBFFF - Free space (12 KB SRAM Using 128KB SRAM)
0xC000-0xFFFF - 16KB EPROM space

CPU

• 65C02 or 65C816 CPU
  • 65C816 requires mods to the PCB (see Checkout notes below) or Rev 2 PCB
• 2 MHz
• Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816

R65C02 vs W65C02 vs W65C816 CPUs

U1 Pin	U1 Pin Name	Sig Name	Pullup	R65C02 sig	W65C02 sig	W65C816 sig
1	VSS/VPB	J2 selects	N	VSS (IN)	VPB (OUT)	VPB (OUT)
3	PH1OUT/ABORT	ABORT*	REV2	PH1OUT (OUT)	PH1OUT (OUT)	ABORT (IN)
5	NC/MLB	MLB	N	NC	MLB (OUT)	MLB (OUT)
7	SYNC/VPA	VPA	N	SYNC (OUT)	SYNC (OUT)	VPA (OUT)
35	NC/E	CPUE	N	NC	NC	EM/NAT (OUT)
36	NC/BE	IORQ*	REV2	NC	BE (IN)	BE (IN)
37	PH0IN/PH2IN	CPUCLK	N	PH0IN	PH2IN	PH2IN
38	SO/MX	CPUMX	REV1/2	SO* (IN)	SOB (IN)	MX (OUT)
39	PH2OUT/VDA	VDA	N	PH2OUT (OUT)	PH2OUT (OUT)	VDA (OUT)

VDA/VPA (65C816)

• VDA/VDA
  • 00, Internal operation (invalid address bus)
  • 01, Valid Program Address
  • 10, Valid Data Address
  • 11, Opcode-fetch

Chip Set

• Ordered from Ebay

• Picture shows 3 MHz CPU
• Received 2 MHz CPU
• As received:

Oscillator

PLD

• ATF16V8B part
• TL866ii_Plus_Programmer

PLD Listing

Name       LB-65CXX-01_PLD;
Partno     ATF16V8B;
Date       08/19/24;
Revision   01;
Designer   DOUG G;
Company    LAND BOARDS LLC;
Assembly   LB65CXX01_U2;
Location   Rustbelt, US;
Device     G16V8;

/*
	65C816 Control
*/

/* Control inputs */
PIN    1   = CLK;
PIN    2   = CPUA12;
PIN    3   = CPUA13;
PIN    4   = CPUA14;
PIN    5   = CPUA15;
PIN    6   = CPUREAD;
PIN    8   = VPA;
PIN    9   = VDA;		/* Pin 39, PH2OUT - Enable line */

/* Address Decode and Chip Select outputs */
PIN    13  = !IOCS;
PIN    14  = !ROMCS;
PIN    15  = !MEMRD;
PIN    16  = !RAMCS;
PIN    18  = RDY;

RAMCS = !CPUA15 & VDA								/* 0x0000-0x7FFF (32KB/64KB SRAM)	*/
#        CPUA15 & !CPUA14 & !CPUA13 & CPUA12 & VDA	/* 0x9000-0x9FFF (128KB SRAM)		*/
#        CPUA15 & !CPUA14 &  CPUA13 & VDA;			/* 0xA000-0xBFFF (128KB SRAM)		*/

IOCS = CPUA15 & !CPUA14 & !CPUA13 & !CPUA12 & VDA;	/* 0x8000-0x8FFF (4KB space)		*/

ROMCS = CPUA15 & CPUA14 & CPUREAD & VDA;			/* 0xC000-0xFFFF (16KB space)		*/

MEMRD = !CPUA15 &                              CPUREAD & VDA	/* 0x0000-0x7FFF		*/
#        CPUA15 & !CPUA14 & !CPUA13 & CPUA12 & CPUREAD & VDA	/* 0x9000-0x9FFF		*/
#        CPUA15 & !CPUA14 &  CPUA13 &          CPUREAD & VDA	/* 0xA000-0xBFFF		*/
#        CPUA15 &  CPUA14 &                    CPUREAD & VDA;	/* 0xC000-0xFFFF		*/

/*
RDY = VDA;
*/

Reset Controller

• DS1813-5 Reset Controller
• 5V Power Monitor
• Reset controller
• Reset pushbutton to ground

Backplane connector

Mechanicals

Checkout

Rev 2

Rev 2 Changes

• Add pull-up resistor on ABORT* line (U1-3)
• Add pull-up resistor on BE line (U1-36)

Rev 1

• Install jumper J2:1-2 if CPU is not a WDC 65C02 or WDC 65C816
• If WDC 65C02 or WDC 65C816 is used:
  • Add pull-up resistor on ABORT* line (U1-3)
  • Add pull-up resistor on BE line (U1-36)

Assembly Sheet

Rev 1

• Interactive BOM