Difference between revisions of "LB-Z80-01"

From Land Boards Wiki
Jump to navigation Jump to search
 
(132 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[file:LB-Z80-01_FRONT-3D.png]]
+
[[file:LB-Z80-01_P138-720px.jpg]]
  
 
== Features ==
 
== Features ==
Line 8: Line 8:
 
* Address decoder PLD drives RAM/ROM/IO chip selects
 
* Address decoder PLD drives RAM/ROM/IO chip selects
 
* 100x50mm card
 
* 100x50mm card
 +
 +
=== Memory Map ===
 +
 +
* 0x0000-0x1FFF 8KB ROM
 +
*  32KB or 56KB SRAM
 +
** 0x8000-0xFFFF Using [[LB-MEM-02]] has 32 KB SRAM
 +
** 0x2000-0xFFFF Using [[LB-MEM-04]] has 128KB or 512 KB of SRAM so 56 KB can be available
 +
* I/O
 +
** 0x00-0x7F - Free
 +
** 0x80-0x81 - Serial port (ACIA)
  
 
== Design ==
 
== Design ==
Line 13: Line 23:
 
=== CPU and Power Supervisor/Reset ===
 
=== CPU and Power Supervisor/Reset ===
  
−
[[file:LB-Z80-01_CPU.PNG]]
+
[[file:LB-Z80-01_CPU_Rev2.PNG]]
 +
 
 +
* Z80 CPU
 +
* Oscillator 8 MHz nominal on card
 +
* Reset switch/power monitor
 +
 
 +
==== Z80 Register Set ====
 +
 
 +
[[file:Z80_Registers.PNG]]
 +
 
 +
=== Memory Access Timing ===
 +
 
 +
[[File:Z80_Mem_Rd_Wr.PNG]]
 +
 
 +
=== I/O Access Timing ===
 +
 
 +
[[File:Z80_IO_Rd_Wr.PNG]]
  
 
=== Oscillator ===
 
=== Oscillator ===
  
 
[[file:LB-Z80-01_OSC.PNG]]
 
[[file:LB-Z80-01_OSC.PNG]]
 +
 +
* 8MHZ or 10 MHz oscillator
  
 
=== PLD ===
 
=== PLD ===
  
−
[[file:LB-Z80-01_PLD.PNG]]
+
* ATF16V8B part
 +
* [[TL866ii Plus Programmer]]
  
−
==== PLS Listing ====
+
[[file:LB-Z80-01_PLD_Rev2.PNG]]
 +
 
 +
==== PLD Listing ====
 +
 
 +
<pre>
 +
Name      LB-Z80-01_PLD;
 +
Partno    ATF16V8B;
 +
Date      10/14/24;
 +
Revision  02;
 +
Designer  DOUG G;
 +
Company    LAND BOARDS LLC;
 +
Assembly  LB-Z80-01_U2;
 +
Location  Rustbelt, US;
 +
Device    G16V8;
 +
 
 +
/* Rev 2 PCB
 +
*/
 +
 
 +
 
 +
/* Control inputs */
 +
PIN    1  = CLK;
 +
PIN    2  = CPUA13;
 +
PIN    3  = CPUA14;
 +
PIN    4  = CPUA15;
 +
PIN    5  = !MREQ;
 +
PIN    6  = !IORQ;
 +
PIN    7  = !M1;
 +
PIN    8  = !CPURD;
 +
PIN    9  = !CPUWR;
 +
PIN    11  = CPUD0;
 +
 
 +
/* Address Decode and Chip Select outputs */
 +
PIN    13  = !ROMCS;
 +
PIN    14  = !IOCS;
 +
PIN    15  = !RAMCS;
 +
PIN    16  = !MEMRD;
 +
/* PIN    17  = !WAIT; */
 +
PIN    18  = LED;
 +
 
 +
ROMCS = !CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPURD;
 +
 
 +
/* 56KB SRAM */
 +
/*
 +
RAMCS = CPUA15 & MREQ
 +
#      CPUA14 & MREQ
 +
#      CPUA13 & MREQ;
 +
*/
 +
 
 +
/* 32KB SRAM */
 +
RAMCS = CPUA15 & MREQ;
 +
 
 +
IOCS = !M1 & IORQ;
 +
 
 +
/*
 +
WAIT = !MREQ # !IORQ;
 +
*/
 +
 
 +
MEMRD = CPURD;
 +
 
 +
LED =    !CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPUWR & CPUD0
 +
# LED & !(!CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPUWR);
 +
 
 +
</pre>
  
 
=== Backplane Connector ===
 
=== Backplane Connector ===
  
 
[[file:LB-Z80-01_BKPL.PNG]]
 
[[file:LB-Z80-01_BKPL.PNG]]
 +
 +
== Software ==
 +
 +
=== Assembly Language Toolchain ===
 +
 +
* TASM.EXE - Telemark Assembler
 +
** [https://www.cpcalive.com/docs/TASMMAN.HTM The Telemark Assembler (TASM) User's Manual]
 +
** '''The version of TASM in Grant's build zip file doesn't run under Win 11'''
 +
*** [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/NASCOM_BASIC TASM version that runs on Win 11]
 +
** TASM80.TAB
 +
*** [Probably need] [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/NASCOM_BASIC the updated TASM80.TAB to run on Win 11]
 +
 +
=== ACIA Loopback Test Code ===
 +
 +
* [https://github.com/douggilliland/Retro-Computers/blob/master/Z80/LB-Z80/AciaTest/AciaTest.asm AciaTest.asm] - Source code
 +
* Type a character, get it back
 +
** 115,200 baud, 1 stop bit, no parity
 +
* Works
 +
 +
=== String Test Code ===
 +
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/StringTest StringTest.asm] - Source code
 +
* String write code
 +
* Includes loopback code
 +
* Works
 +
 +
=== String Read/Interpreter Code ===
 +
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/ReadStringTest ReadStringTest.asm] - Source code
 +
* Adds a string read function
 +
* Adds an interpreter skeleton
 +
* Works with Rev 1 card
 +
* Added LED command (Rev 2 card)
 +
** L0 - Turn off the LED
 +
** L1 - Turn on the LED
 +
* Works with Rev 2 card
 +
 +
=== NASCOM 2 BASIC ===
 +
 +
* Microsoft BASIC 4.7 modified to remove all hardware-specific code
 +
** Use [http://searle.x10host.com/z80/SimpleZ80_32K.html Grant Searle's 32KB SRAM version] if the [[LB-MEM-02]] card is used
 +
** Use [http://searle.x10host.com/z80/SimpleZ80.html Grant's 56KB version] if the [[LB-MEM-03]] card is used
 +
* Needed to make some minor changes to get the code to run
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/NASCOM_BASIC Code Repo]
 +
* Works
 +
 +
[[FILE:NASCOM_BOOT.PNG]]
 +
 +
==== Short Test Program ====
 +
 +
<pre>
 +
10 I=0
 +
20 PRINTI:I=I+1:GOTO 20
 +
 +
</pre>
 +
 +
==== Build Details ====
 +
 +
* TASM assembler (see above)
 +
* S Record and Hex file manipulation
 +
** [https://carta.tech/man-pages/man1/srec_examples.1.html Examples of srec_cat utility]
 +
** [https://srecord.sourceforge.net/man/man1/srec_cat.1.html srec_cat man page]
 +
* Adds srec_cat to combine files into one Intel Hex file
 +
** Combine [https://github.com/douggilliland/Retro-Computers/blob/master/Z80/LB-Z80/NASCOM_BASIC/INT32K.HEX int32k.hex] and [https://github.com/douggilliland/Retro-Computers/blob/master/Z80/LB-Z80/NASCOM_BASIC/BAS32K.HEX BAS32K.HEX] into [https://github.com/douggilliland/Retro-Computers/blob/master/Z80/LB-Z80/NASCOM_BASIC/rom32.hex rom32.hex] using srec-cat
 +
** Command line
 +
*** srec_cat.exe int32k.hex -Intel BAS32K.HEX -Intel -fill 0xff 0x0144 0x014f -o rom32.hex -Intel
 +
* _ASSEMBLE.BAT - double-click in Windows to run the assembly if needed
 +
 +
==== NASCOM BASIC - Code Repository ====
 +
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/NASCOM_BASIC NASCOM BASIC Source Code] - 32KB version
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/Z80/LB-Z80/NASCOM_BASIC/NASCOM_56K NASCOM BASIC Source Code] - 56KB version
 +
 +
==== Source files ====
 +
 +
* intmini.asm - the interupt driven mini startup program needed to boot into BASIC
 +
* basic.asm - BASIC 4.7b - a conversion of Microsoft BASIC 4.7, as used on the Nascom computers (see below for details)
 +
 +
==== Output files ====
 +
 +
* List files
 +
** INTMINI.LST
 +
** BASIC.LST
 +
* Hex files
 +
** INTMINI.HEX
 +
** BASIC.HEX
 +
** ROM32.HEX - the complete 8K ROM ready for burning to an EPROM
 +
*** The unused contents are filled with FF values.
 +
*** Within the ROM, the serial handler is first (starting at address 0000H), followed by the BASIC interpreter (starting at 0100H).
 +
* [https://en.wikipedia.org/wiki/Intel_HEX Hex file format]
 +
 +
[[file:IntelHexRecordFormat.png]]
 +
 +
==== Acknowledgements ====
 +
 +
* BASIC is Microsoft BASIC 4.7 for the NASCOM, heavily modified by Grant to remove references to different monitors, screen handlers and keyboard matrix reading
 +
* TASM assembler is a partial distribution of the package from Speech Technology Incorporated
 +
 +
=== Software Development Tools ===
 +
 +
* [https://sdcc.sourceforge.net/ SDCC - Small Device C Compiler]
 +
** [https://sdcc.sourceforge.net/doc/sdccman.pdf SDCC Compiler User Guide]
 +
 +
=== References ===
 +
 +
* [https://ia800203.us.archive.org/27/items/Z80_Assembly_Language_Programming/Z80_Assembly_Language_Programming.pdf Z80 Assembly Language Programming] - Concise  description of the register set, Chapter 3 page 1-42 of Z80, assembly language programming by Leventhal, Lance A.
 +
* [https://ia803204.us.archive.org/4/items/Programming_the_Z-80_2nd_Edition_1980_Rodnay_Zaks/Programming_the_Z-80_2nd_Edition_1980_Rodnay_Zaks.pdf Programming the Z80] 1980 Rodnay Zaks
 +
* [https://archive.org/details/Z80_Assembly_Language_Programming_1979_Leventhal Z80, assembly language programming by Leventhal, Lance A., 1945-]
 +
* ASCII Table
 +
 +
[[file:ASCII_TABLE.PNG]]
  
 
== Mechanicals ==
 
== Mechanicals ==
 +
 +
=== Rev 2 Mechanicals ===
 +
 +
[[file:LB-Z80-01_MECH_Rev2.PNG]]
 +
 +
=== Rev 1 Mechanicals ===
 +
 +
[[file:LB-Z80-01_MECH.PNG]]
  
 
== Checkout ==
 
== Checkout ==
  
−
=== Rev 1 ===
+
=== Rev 2 Checkout ===
 +
 
 +
* Reset switch footprint is good
 +
* LED control worked with software update
 +
** Write 1 to address in range 0x0000-0x1FFF to turn LED on (command L1)
 +
** Write 0 to address in range 0x0000-0x1FFF to turn LED off (command L0)
 +
* Serial test software runs
 +
* MS BASIC doesn't work
 +
 
 +
=== Rev 2 Changes ===
 +
 
 +
* Fixed resistor silkscreen values
 +
* Re-sequenced resistor reference designator
 +
* Made reset switch right angle
 +
* Add LED and resistor to PLD pin 15
 +
* Add CPUD0 to PLD pin 11
 +
* Added bulk capacitor
 +
 
 +
[[file:LB-Z80-01_FRONT-Rev-2_3D.png]]
 +
 
 +
=== Rev 1 Checkout ===
 +
 
 +
* Didn't use silkscreen values, used
 +
** R1 = 4.7K
 +
** Other resistors are 10K
 +
* [[LB-BKOUT-01#NOP_Tester nop tester|Z80 nop tester]] nop = 0x00
 +
** Refresh complicates this
 +
* Made C2 a bulk cap (100uF)
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
 +
 +
* [https://land-boards.com/LB-Z80-01/LB-Z80-01_Rev1_ibom.html Interactive BOM]

Latest revision as of 23:18, 14 October 2024

LB-Z80-01 P138-720px.jpg

Features

  • Z80 CPU
  • Oscillator 8 MHz nominal on card
  • Reset switch/power monitor
  • Address decoder PLD drives RAM/ROM/IO chip selects
  • 100x50mm card

Memory Map

  • 0x0000-0x1FFF 8KB ROM
  • 32KB or 56KB SRAM
    • 0x8000-0xFFFF Using LB-MEM-02 has 32 KB SRAM
    • 0x2000-0xFFFF Using LB-MEM-04 has 128KB or 512 KB of SRAM so 56 KB can be available
  • I/O
    • 0x00-0x7F - Free
    • 0x80-0x81 - Serial port (ACIA)

Design

CPU and Power Supervisor/Reset

LB-Z80-01 CPU Rev2.PNG

  • Z80 CPU
  • Oscillator 8 MHz nominal on card
  • Reset switch/power monitor

Z80 Register Set

Z80 Registers.PNG

Memory Access Timing

Z80 Mem Rd Wr.PNG

I/O Access Timing

Z80 IO Rd Wr.PNG

Oscillator

LB-Z80-01 OSC.PNG

  • 8MHZ or 10 MHz oscillator

PLD

LB-Z80-01 PLD Rev2.PNG

PLD Listing

Name       LB-Z80-01_PLD;
Partno     ATF16V8B;
Date       10/14/24;
Revision   02;
Designer   DOUG G;
Company    LAND BOARDS LLC;
Assembly   LB-Z80-01_U2;
Location   Rustbelt, US;
Device     G16V8;

/* Rev 2 PCB
*/


/* Control inputs */
PIN    1   = CLK;
PIN    2   = CPUA13;
PIN    3   = CPUA14;
PIN    4   = CPUA15;
PIN    5   = !MREQ;
PIN    6   = !IORQ;
PIN    7   = !M1;
PIN    8   = !CPURD;
PIN    9   = !CPUWR;
PIN    11  = CPUD0;

/* Address Decode and Chip Select outputs */
PIN    13  = !ROMCS;
PIN    14  = !IOCS;
PIN    15  = !RAMCS;
PIN    16  = !MEMRD;
/* PIN    17  = !WAIT; */
PIN    18  = LED;

ROMCS = !CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPURD;

/* 56KB SRAM */
/*
RAMCS = CPUA15 & MREQ
#       CPUA14 & MREQ
#       CPUA13 & MREQ;
*/

/* 32KB SRAM */
RAMCS = CPUA15 & MREQ;

IOCS = !M1 & IORQ;

/*
WAIT = !MREQ # !IORQ;
*/

MEMRD = CPURD;

LED =     !CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPUWR & CPUD0
# LED & !(!CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPUWR);

Backplane Connector

LB-Z80-01 BKPL.PNG

Software

Assembly Language Toolchain

ACIA Loopback Test Code

  • AciaTest.asm - Source code
  • Type a character, get it back
    • 115,200 baud, 1 stop bit, no parity
  • Works

String Test Code

  • StringTest.asm - Source code
  • String write code
  • Includes loopback code
  • Works

String Read/Interpreter Code

  • ReadStringTest.asm - Source code
  • Adds a string read function
  • Adds an interpreter skeleton
  • Works with Rev 1 card
  • Added LED command (Rev 2 card)
    • L0 - Turn off the LED
    • L1 - Turn on the LED
  • Works with Rev 2 card

NASCOM 2 BASIC

NASCOM BOOT.PNG

Short Test Program

10 I=0
20 PRINTI:I=I+1:GOTO 20

Build Details

  • TASM assembler (see above)
  • S Record and Hex file manipulation
  • Adds srec_cat to combine files into one Intel Hex file
    • Combine int32k.hex and BAS32K.HEX into rom32.hex using srec-cat
    • Command line
      • srec_cat.exe int32k.hex -Intel BAS32K.HEX -Intel -fill 0xff 0x0144 0x014f -o rom32.hex -Intel
  • _ASSEMBLE.BAT - double-click in Windows to run the assembly if needed

NASCOM BASIC - Code Repository

Source files

  • intmini.asm - the interupt driven mini startup program needed to boot into BASIC
  • basic.asm - BASIC 4.7b - a conversion of Microsoft BASIC 4.7, as used on the Nascom computers (see below for details)

Output files

  • List files
    • INTMINI.LST
    • BASIC.LST
  • Hex files
    • INTMINI.HEX
    • BASIC.HEX
    • ROM32.HEX - the complete 8K ROM ready for burning to an EPROM
      • The unused contents are filled with FF values.
      • Within the ROM, the serial handler is first (starting at address 0000H), followed by the BASIC interpreter (starting at 0100H).
  • Hex file format

IntelHexRecordFormat.png

Acknowledgements

  • BASIC is Microsoft BASIC 4.7 for the NASCOM, heavily modified by Grant to remove references to different monitors, screen handlers and keyboard matrix reading
  • TASM assembler is a partial distribution of the package from Speech Technology Incorporated

Software Development Tools

References

ASCII TABLE.PNG

Mechanicals

Rev 2 Mechanicals

LB-Z80-01 MECH Rev2.PNG

Rev 1 Mechanicals

LB-Z80-01 MECH.PNG

Checkout

Rev 2 Checkout

  • Reset switch footprint is good
  • LED control worked with software update
    • Write 1 to address in range 0x0000-0x1FFF to turn LED on (command L1)
    • Write 0 to address in range 0x0000-0x1FFF to turn LED off (command L0)
  • Serial test software runs
  • MS BASIC doesn't work

Rev 2 Changes

  • Fixed resistor silkscreen values
  • Re-sequenced resistor reference designator
  • Made reset switch right angle
  • Add LED and resistor to PLD pin 15
  • Add CPUD0 to PLD pin 11
  • Added bulk capacitor

LB-Z80-01 FRONT-Rev-2 3D.png

Rev 1 Checkout

  • Didn't use silkscreen values, used
    • R1 = 4.7K
    • Other resistors are 10K
  • Z80 nop tester nop = 0x00
    • Refresh complicates this
  • Made C2 a bulk cap (100uF)

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=LB-Z80-01&oldid=27330"