|
|
| (26 intermediate revisions by the same user not shown) |
| Line 3: |
Line 3: |
| | == Features == | | == Features == |
| | | | |
| − | * Blue Pill and Black Pill Board Features | + | * [[STM32 Blue Pill]] Board |
| | + | * [[STM32 Black Pill]] Board |
| | | | |
| − | === Blue Pill Board Features ===
| + | == Blue Pill vs Black Pill Pinout == |
| − | | |
| − | Used on [[BLUE-PILL-HUB]] card
| |
| − | | |
| − | * STM32F103
| |
| − | ** 72 MHz
| |
| − | ** 64KB Flash (most have 128KB)
| |
| − | ** 20 KB SRAM
| |
| − | ** 3.3V regulator
| |
| − | ** 16 MHz
| |
| − | ** 1 of x12-bit, A/D converter
| |
| − | ** 7-channel DMA controller
| |
| − | ** SPI, I2C, UART interfaces
| |
| − | ** 7 timers
| |
| − | * MicroUSB
| |
| − | * Reset button
| |
| − | * Download jumper
| |
| − | ** Replaced with a slide switch
| |
| − | * Power LED
| |
| − | * PC 13 LED
| |
| − | * SWD connector
| |
| − | * RTC crystal
| |
| − | * '''Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.'''
| |
| − | | |
| − | | |
| − | [[File:STM32F103C8T6-Blue-Pill-Pin-Layout.gif]]
| |
| − | | |
| − | === Black Pill Board Features ===
| |
| − | | |
| − | '''Not pin compatible with Blue Pill due to power pin locations'''
| |
| − | | |
| − | Can't be used on [[BLUE-PILL-HUB]] card without modifications
| |
| − | | |
| − | * [[STM32F4XX|STM32F401CCU6 or STM32F411CCU6 CPU]]
| |
| − | ** 84/100 MHz
| |
| − | ** 256/512 KB Flash (most have 128KB)
| |
| − | ** 64/128 KB SRAM
| |
| − | ** 3.3V regulator
| |
| − | ** 2x12-bit, A/D converter
| |
| − | ** 7-channel DMA controller
| |
| − | ** SPI, I2C, UART interfaces
| |
| − | ** 7 timers
| |
| − | * SPI ROM footprint that fits an W25Q32JVSSIQ 32 Mbit SPI Flash ROM,
| |
| − | * USB-C
| |
| − | * Reset button
| |
| − | * Power LED
| |
| − | * PC 13 LED
| |
| − | * SWD connector
| |
| − | * '''Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.'''
| |
| − | | |
| − | [[File:BlackPillBoard-720px.png]]
| |
| − | | |
| − | * [https://stm32-base.org/boards/STM32F401CCU6-WeAct-Black-Pill-V1.2.html WeAct Black Pill V1.2] - Helpful page
| |
| − | | |
| − | === Blue Pill vs Black Pill Pinout ===
| |
| | | | |
| | * '''Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.''' | | * '''Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.''' |
| Line 67: |
Line 14: |
| | | | |
| | [[File:Blue-vs-Black-Pill-Pin-Layout.png]] | | [[File:Blue-vs-Black-Pill-Pin-Layout.png]] |
| − |
| |
| − | == Arduino IDE ==
| |
| − |
| |
| − | * [https://github.com/rogerclarkmelbourne/Arduino_STM32 Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards]
| |
| − | ** [https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki Arduino STM32 Wiki]
| |
| − | ** [https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki/Installation Installation]
| |
| − | * [https://www.instructables.com/id/Programming-STM32-Blue-Pill-Via-USB/ Arduino Alternative - STM32 Blue Pill Programming Via USB]
| |
| − |
| |
| − | === Uploading Code to Blue Pill ===
| |
| − |
| |
| − | * FTDI connection to Blue Pill Hub FTDI connector
| |
| − | ** FTDI TX (to Blue Pill RX) (PA10 pin on STM32)
| |
| − | ** FTDI RX (to Blue Pill Tx) (PA9 pin on STM32)
| |
| − | * Set Switch (or jumper) on Blue Pill module set towards center of card to upload card to board
| |
| − |
| |
| − | [[File:BluePill_Jumper.png]]
| |
| − |
| |
| − | * In Arduino IDE,
| |
| − | ** Tools
| |
| − | *** Board "Generic..."
| |
| − | *** Upload method: "Serial..."
| |
| − | *** Port: [the comm port]
| |
| − |
| |
| − | [[File:ArduinoIDE_Tools_Menu.png]]
| |
| − |
| |
| − | * Upload code
| |
| − | ** Takes a while
| |
| − | * Set Switch (or jumper) on Blue Pill module set towards edge of card to run
| |
| − | * Press reset button
| |
| − |
| |
| − | == Blue Pill Card Boot Jumpers ==
| |
| − |
| |
| − | [[File:BootJumpers.PNG]]
| |
| − |
| |
| − | === Annotated ===
| |
| − |
| |
| − | [[File:STM32-Annotated.jpg]]
| |
| − |
| |
| − | == Mechanicals ==
| |
| − |
| |
| − | === Blue Pill Mechanicals ===
| |
| − |
| |
| − | [[File:STM32-Mechanicals-2.jpg]]
| |
| − |
| |
| − | === Black Pill Mechanicals ===
| |
| − |
| |
| − | [[File:original-dimensions-STM32F401CCU6_WeAct_Black_Pill_V1.2.png]]
| |
| − |
| |
| − | == Schematic ==
| |
| − |
| |
| − | === Blue Pill Card Schematic ===
| |
| − |
| |
| − | [[File:STM32-Schematic.jpg]]
| |
| − |
| |
| − | === Black Pill Card Schematic ===
| |
| − |
| |
| − | [https://github.com/land-boards/lb-boards/blob/master/Arduino%20Cards/Black-Pill-Hub/Documents/BlackPillBoard/original-schematic-STM32F401CCU6_WeAct_Black_Pill_V1.2.pdf Schematic]
| |
