LB-Z80-01

Features

• Z80 CPU
• Oscillator 8 MHz nominal on card
• Reset switch/power monitor
• Address decoder PLD drives RAM/ROM/IO chip selects
• 100x50mm card

Memory Map

• 0x0000-0x1FFF 8KB ROM
• 32KB or 56KB SRAM
  • 0x8000-0xFFFF Using LB-MEM-02 has 32 KB SRAM
  • 0x2000-0xFFFF Using LB-MEM-03 has 128KB or 512 KB of SRAM so 56 KB can be available
• I/O
  • 0x00-0x7F - Free
  • 0x80-0x81 - Serial port (ACIA)

Design

CPU and Power Supervisor/Reset

• Z80 CPU
• Oscillator 8 MHz nominal on card
• Reset switch/power monitor

Memory Access Timing

I/O Access Timing

Oscillator

• 8MHZ or 10 MHz oscillator

PLD

• ATF16V8B part
• TL866ii Plus Programmer

PLD Listing

Name       LB-Z80-01_PLD;
Partno     ATF16V8B;
Date       09/17/20;
Revision   01;
Designer   DOUG G;
Company    LAND BOARDS LLC;
Assembly   LB-Z80-01_U2;
Location   Rustbelt, US;
Device     G16V8;

/*
*/


/* Control inputs */
PIN    1   = CLK;
PIN    2   = CPUA13;
PIN    3   = CPUA14;
PIN    4   = CPUA15;
PIN    5   = !MREQ;
PIN    6   = !IORQ;
PIN    7   = !M1;
PIN    8   = !CPURD;
PIN    9   = !CPUWR;

/* Address Decode and Chip Select outputs */
PIN    13  = !ROMCS;
PIN    14  = !IOCS;
PIN    16  = !MEMRD;
PIN    15  = !RAMCS;
PIN    18  = !WAIT;

ROMCS = !CPUA15 & !CPUA14 & !CPUA13 & MREQ & CPURD;

RAMCS = CPUA15 & MREQ
#       CPUA14 & MREQ
#       CPUA13 & MREQ;

IOCS = !M1 & IORQ;

WAIT = !MREQ # !IORQ;

MEMRD = CPURD;

Backplane Connector

Software

Register Set

Nascom 2 Computer BASIC

• Microsoft BASIC 4.7 modified to remove all hardware-specific code

• Grant Searle's 32KB SRAM version
  • Need to use Grant's 32KB version if the LB-MEM-02 card is used
  • Can use Grant's 56KB version if the LB-MEM-03 card is used

NASCOM BASIC - Assembler Source files (for Windows/DOS)

• NASCOM BASIC Source Code - 32KB version
• NASCOM BASIC Source Code - 56KB version

Toolchain

• Assembler files (for Windows 11/DOS)
  • _ASSEMBLE.BAT - double-click in Windows to run the assembly if needed
    • Adds srec_cat to combine files into one Intel Hex file
  • TASM.EXE
  • The version of TASM in Grant's build zip file doesn't run under Win 11
    • TASM version that runs on Win 11
  • TASM80.TAB
    • [Probably need] the updated one in to run on Win 11

Source files

• intmini.asm - the interupt driven mini startup program needed to boot into BASIC
• basic.asm - BASIC 4.7b - a conversion of Microsoft BASIC 4.7, as used on the Nascom computers (see below for details)

Output files

• INTMINI.HEX
• BASIC.HEX
• ROM.HEX - the complete 8K ROM ready for burning to an EPROM - the unused contents are filled with FF values.
• Within the ROM, the serial handler is first (starting at address 0000H), followed by the BASIC interpreter (starting at 0100H).

S Record and Hex file manipulation

• Examples of srec_cat utility
• srec_cat man page
• Combine int32k.hex and BAS32K.HEX into rom32.hex

srec_cat.exe int32k.hex -Intel BAS32K.HEX -Intel -fill 0xff 0x0144 0x014f -o rom32.hex -Intel

Acknowledgements

• BASIC is Microsoft BASIC 4.7 for the NASCOM, heavily modified by Grant to remove references to different monitors, screen handlers and keyboard matrix reading
• TASM assembler is a partial distribution of the package from Speech Technology Incorporated

References

• Z80 Assembly Language Programming - Concise description of the register set, Chapter 3 page 1-42 of Z80, assembly language programming by Leventhal, Lance A.
• Programming the Z80 1980 Rodnay Zaks
• Z80, assembly language programming by Leventhal, Lance A., 1945-
• ASCII Table

Mechanicals

Checkout

Rev 2 Changes

• Fixed resistor silkscreen values
• Re-sequenced resistor reference designator
• Made reset switch right angle
• Add LED and resistor to PLD pin 15
• Add CPUD0 to PLD pin 11
• Added bulk capacitor

Rev 1

• Didn't use silkscreen values, used
  • R1 = 4.7K
  • Other resistors are 10K
• Z80 nop tester nop = 0x00
  • Refresh complicates this
• Made C2 a bulk cap (100uF)

Assembly Sheet

• Interactive BOM