Difference between revisions of "ATProgHead"

From Land Boards Wiki
Jump to navigation Jump to search
Line 54: Line 54:
  
 
[[File:ATProghead-X2-PWB.PNG]]
 
[[File:ATProghead-X2-PWB.PNG]]
 +
 +
== Revisions ==
 +
 +
=== Revision X2 ===
 +
 +
Revisions X2 is in development.
 +
 +
* Corrects issues found in Revision X1 boards.
 +
* Adds 6 pin ISP connector as H2.
 +
* [[GVSDuino]] changed to move D10 from pin 5 to pin 7 and add RST where D10 was previously.
 +
**This allows GVSDuino to be programmed from the ISP connector and still support the ATProgHead adapter
 +
*** Requires Rev X4 GVSDuino
 +
<pre>
 +
kiCompNL.py
 +
 +
First netlist: C:\Users\doug_000\Documents\GitHub\lb-boards\ATProgHead\ATProgHead-X1\ATProgHead.net
 +
Number of Nets: 39
 +
Second netlist: C:\Users\doug_000\Documents\GitHub\lb-boards\ATProgHead\ATProgHead.net
 +
Number of Nets: 39
 +
Mismatch in net (1):  diff ['H1-7']
 +
Mismatch in net (1):  diff ['H1-7']
 +
Mismatch in net (1):  diff ['H1-7']
 +
Mismatch in net (1):  diff ['H1-7']
 +
net is in 1 but not 2 ['MISO', 'U1-18', 'H1-1', 'U2-6']
 +
net is in 1 but not 2 ['SCK', 'U1-19', 'U2-7', 'H1-3']
 +
Mismatch in net (1):  diff ['U1-16']
 +
Mismatch in net (1):  diff ['U1-16']
 +
Mismatch in net (1):  diff ['U1-16']
 +
Mismatch in net (1):  diff ['U1-16']
 +
net is in 1 but not 2 ['RST', 'H1-5', 'U2-1', 'U1-1']
 +
net is in 1 but not 2 ['MOSI', 'U1-17', 'U2-5', 'H1-4']
 +
Mismatch in net (1): 5V diff ['D3-1', 'D2-1', 'D1-1']
 +
net is in 1 but not 2 ['PROG', 'R1-1', 'H1-8']
 +
net is in 1 but not 2 ['ERR', 'R2-1', 'H1-10']
 +
net is in 1 but not 2 ['HTBT', 'H1-12', 'R3-1']
 +
Mismatch in net (1): PG diff ['D1-2']
 +
Mismatch in net (1): ER diff ['D2-2']
 +
Mismatch in net (1): HB diff ['D3-2']
 +
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
 +
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
 +
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
 +
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
 +
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
 +
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
 +
Mismatch in net (2): ND diff ['D3-2', 'H2-6', 'D1-2', 'D2-2']
 +
Mismatch in net (2): 5V diff ['H2-2']
 +
Mismatch in net (2):  diff ['H1-5']
 +
Mismatch in net (2):  diff ['H1-5']
 +
Mismatch in net (2):  diff ['H1-5']
 +
Mismatch in net (2):  diff ['H1-5']
 +
net is in 2 but not 1 ['MISO-D12', 'U1-18', 'H2-1', 'H1-1', 'U2-6']
 +
net is in 2 but not 1 ['SCK-D13', 'U1-19', 'H2-3', 'H1-3', 'U2-7']
 +
net is in 2 but not 1 ['RST-D10', 'U1-1', 'U2-1', 'H2-5', 'H1-7']
 +
net is in 2 but not 1 ['MOSI-D11', 'H1-4', 'H2-4', 'U2-5', 'U1-17']
 +
net is in 2 but not 1 ['PROG-D7', 'R1-1', 'H1-8']
 +
net is in 2 but not 1 ['ERR-D8', 'R2-1', 'H1-10']
 +
net is in 2 but not 1 ['HTBT-D9', 'H1-12', 'R3-1']
 +
Mismatch in net (2): PG diff ['D1-1']
 +
Mismatch in net (2): ER diff ['D2-1']
 +
Mismatch in net (2): HB diff ['D3-1']
 +
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
 +
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
 +
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
 +
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
 +
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
 +
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
 +
Mismatch in net (2):  diff ['U1-28']
 +
Mismatch in net (2):  diff ['U1-28']
 +
Mismatch in net (2):  diff ['U1-28']
 +
Mismatch in net (2):  diff ['U1-28']
 +
</pre>

Revision as of 13:12, 10 January 2020

ATmel Programmer Head

Description

The ATmel Programming Head (ATProgHead) is used to program 28-pin and 8-pin Atmel (AVR) microprocessors.

ATProgHead-X2-CCA-640-001.jpg

Here is the ATProgHead installed on top of the GVSDuino (Rev X4 or higher) and a FTDI-USB-TTL card in a 3D printed case.

Features

ATProgHead board features include:

  • Daughter card to the GVSDuino (Revision X4 or higher) and gets installed above the GVSDuino board
  • Status LEDs
    • PROG - Programming in progress
    • ERR - Error while programming
  • ALIV - Heartbeat
  • On-board 16 MHz resonator
  • Extended 12-pin ISP connector on bottom of board
  • Separate 6-pin ISP header allows board to act as an ISP programmer
  • The GVSDuino uses an FTDI-USB-TTL board for its USB host connection.
  • ATProgHead supports ATMega328P, ATTiny85 and other Atmel AVR parts.
  • Can be used to load bootloader onto factory fresh chips.
  • Can be used to load sketches onto chips without the overhead of the bootloader.
  • 28-pin ATMega328P socket has a Zero Insertion Force socket which allows for easier programming than standard sockets (no tools required).
  • 8-pin DIP socket for ATTiny parts
  • 100mm square form factor
  • 4-40 mounting hardware
    • 3D printed standoffs for spacing off GVSDuino card

Compatible Software

Connectors

H1 - GVS Duino interconnect cable

The connector from the GVSDuino to the ATProgHead is:

ATProghead-X2-H1.PNG

H2 - ISP Cable Connector

The ISP Connector pinout is:

ATProghead-X2-H2.PNG

Board Dimensions

ATProghead-X2-PWB.PNG

Revisions

Revision X2

Revisions X2 is in development.

  • Corrects issues found in Revision X1 boards.
  • Adds 6 pin ISP connector as H2.
  • GVSDuino changed to move D10 from pin 5 to pin 7 and add RST where D10 was previously.
    • This allows GVSDuino to be programmed from the ISP connector and still support the ATProgHead adapter
      • Requires Rev X4 GVSDuino
kiCompNL.py

First netlist: C:\Users\doug_000\Documents\GitHub\lb-boards\ATProgHead\ATProgHead-X1\ATProgHead.net
Number of Nets: 39
Second netlist: C:\Users\doug_000\Documents\GitHub\lb-boards\ATProgHead\ATProgHead.net
Number of Nets: 39
Mismatch in net (1):  diff ['H1-7']
Mismatch in net (1):  diff ['H1-7']
Mismatch in net (1):  diff ['H1-7']
Mismatch in net (1):  diff ['H1-7']
net is in 1 but not 2 ['MISO', 'U1-18', 'H1-1', 'U2-6']
net is in 1 but not 2 ['SCK', 'U1-19', 'U2-7', 'H1-3']
Mismatch in net (1):  diff ['U1-16']
Mismatch in net (1):  diff ['U1-16']
Mismatch in net (1):  diff ['U1-16']
Mismatch in net (1):  diff ['U1-16']
net is in 1 but not 2 ['RST', 'H1-5', 'U2-1', 'U1-1']
net is in 1 but not 2 ['MOSI', 'U1-17', 'U2-5', 'H1-4']
Mismatch in net (1): 5V diff ['D3-1', 'D2-1', 'D1-1']
net is in 1 but not 2 ['PROG', 'R1-1', 'H1-8']
net is in 1 but not 2 ['ERR', 'R2-1', 'H1-10']
net is in 1 but not 2 ['HTBT', 'H1-12', 'R3-1']
Mismatch in net (1): PG diff ['D1-2']
Mismatch in net (1): ER diff ['D2-2']
Mismatch in net (1): HB diff ['D3-2']
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
Mismatch in net (1):  diff ['U1-10', 'Y1-3']
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
Mismatch in net (1):  diff ['Y1-1', 'U1-9']
Mismatch in net (2): ND diff ['D3-2', 'H2-6', 'D1-2', 'D2-2']
Mismatch in net (2): 5V diff ['H2-2']
Mismatch in net (2):  diff ['H1-5']
Mismatch in net (2):  diff ['H1-5']
Mismatch in net (2):  diff ['H1-5']
Mismatch in net (2):  diff ['H1-5']
net is in 2 but not 1 ['MISO-D12', 'U1-18', 'H2-1', 'H1-1', 'U2-6']
net is in 2 but not 1 ['SCK-D13', 'U1-19', 'H2-3', 'H1-3', 'U2-7']
net is in 2 but not 1 ['RST-D10', 'U1-1', 'U2-1', 'H2-5', 'H1-7']
net is in 2 but not 1 ['MOSI-D11', 'H1-4', 'H2-4', 'U2-5', 'U1-17']
net is in 2 but not 1 ['PROG-D7', 'R1-1', 'H1-8']
net is in 2 but not 1 ['ERR-D8', 'R2-1', 'H1-10']
net is in 2 but not 1 ['HTBT-D9', 'H1-12', 'R3-1']
Mismatch in net (2): PG diff ['D1-1']
Mismatch in net (2): ER diff ['D2-1']
Mismatch in net (2): HB diff ['D3-1']
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
Mismatch in net (2):  diff ['U1-9', 'Y1-1']
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
Mismatch in net (2):  diff ['Y1-3', 'U1-10']
Mismatch in net (2):  diff ['U1-28']
Mismatch in net (2):  diff ['U1-28']
Mismatch in net (2):  diff ['U1-28']
Mismatch in net (2):  diff ['U1-28']