Difference between revisions of "PE4302 RF Attenuator"

From Land Boards Wiki
Jump to navigation Jump to search
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[file:PE4302_P1833-720px.jpg]]
 +
 +
== Features ==
 +
 +
* [http://www.west-l.com/uploads/tdpdf/yqperegrine_hf-switch-pe4302_en.pdf PE4302] RF attenuator module
 +
 
[[File:RF_Atten-Front-01.jpg]]
 
[[File:RF_Atten-Front-01.jpg]]
  
 
[[File:RF_Atten-Rear-01.jpg]]
 
[[File:RF_Atten-Rear-01.jpg]]
  
== Features ==
 
 
* [http://www.west-l.com/uploads/tdpdf/yqperegrine_hf-switch-pe4302_en.pdf PE4302] RF attenuator module
 
 
* Parallel immediate mode
 
* Parallel immediate mode
 
* Program control gain attenuation range is from 0 to 31.5dB
 
* Program control gain attenuation range is from 0 to 31.5dB
Line 30: Line 33:
 
** SMA-female
 
** SMA-female
  
== My Design ==
+
== My Build ==
 +
 
 +
[[file:PE4302_P1833-720px.jpg]]
 +
 
 +
[[file:PE4302_P1831-720px.jpg]]
 +
 
 +
[[file:PE4302_P1832-720px.jpg]]
  
 
* A lot of designs use Arduino/OLED, etc to control the card - unnecessary
 
* A lot of designs use Arduino/OLED, etc to control the card - unnecessary
Line 39: Line 48:
 
** Board connector for one SMA
 
** Board connector for one SMA
 
** Short cable male SMA to SMA female bulkhead SMA for other end
 
** Short cable male SMA to SMA female bulkhead SMA for other end
* PE6402 remove straight header, replace with right angle connector over card
+
* PE4302 remove straight header, replace with right angle connector over card
 
* [[Mini360 Adapter Board]] for wide input voltage range
 
* [[Mini360 Adapter Board]] for wide input voltage range
 
** 4.75-23V input
 
** 4.75-23V input
Line 65: Line 74:
  
 
* NanoVNA
 
* NanoVNA
* 1-300 MHz
+
** Sweeping from 1-300 MHz
 
* All switches set to GND
 
* All switches set to GND
* Min -1.2 dB insertion loss
+
* Approx 2 dB insertion loss
 
* S21 Gain zoomed in
 
* S21 Gain zoomed in
  

Latest revision as of 01:03, 13 September 2021

PE4302 P1833-720px.jpg

Features

RF Atten-Front-01.jpg

RF Atten-Rear-01.jpg

  • Parallel immediate mode
  • Program control gain attenuation range is from 0 to 31.5dB
  • Bandwidth 1MHz to 4GHz

Specifications

  • Power Supply Voltage
    • 2.7-3.3 VDC - 3V typical
    • Typical current 5mA
  • Program control gain attenuation range
    • 0~31.5DB
    • 10K pull down resistors to ground
    • Step size: 0.5DB
  • Input/Output Impedance
    • 50 ohm
  • Bandwidth
    • 1MHz~4GHz
    • Attenuation value will differ under different frequency
  • Max Input power (50Ω)
    • +30 dBm
    • 1W = 7.1V RMS
  • Connectors
    • SMA-female

My Build

PE4302 P1833-720px.jpg

PE4302 P1831-720px.jpg

PE4302 P1832-720px.jpg

  • A lot of designs use Arduino/OLED, etc to control the card - unnecessary
    • Could add noise from OLED
    • Doesn't need to switch too often
  • Mount in small 80mm x 50mm x 20mm project box
  • SMA connectors
    • Board connector for one SMA
    • Short cable male SMA to SMA female bulkhead SMA for other end
  • PE4302 remove straight header, replace with right angle connector over card
  • Mini360 Adapter Board for wide input voltage range
    • 4.75-23V input
    • 3V output
    • Concern over EMI?
    • Right angle connector 2x3 min
  • Use SWLEDX8 to control attenuation selection
    • Right angle 2x10 under card for low profile installation
    • Use SW1-SW6 switches (centered horizontally on card)
    • Digital Input High 0.7xVDD in V = 2.1V
    • Using 1.2K-1.5K pullup to counter the 10K pulldowns on the card = 2.6V
    • When switch is on/low - 3V / 1.5K = 2 mA
    • Adds to current 2 mA x 6 = 12 mA when all switches are low
    • Use D7 for power indication
      • Vf = 1.8V, 3V-1.8V = 1.2V, 3 mA for lower light level - use 470 ohm resistor
  • Cabling
    • 1x7 pin PE4302 connector (Use 1x8, ignore 8th pin)
    • 2x10 Dupont connector for SWLEDX8
      • Ground, power to D7 LED, 6 switches
    • 2x3 Dupont connector with pins from Mini360 Adapter Board

SWLEDX8-720px.jpg

Measurements

  • NanoVNA
    • Sweeping from 1-300 MHz
  • All switches set to GND
  • Approx 2 dB insertion loss
  • S21 Gain zoomed in

SW All 0s-ZoomedIn.PNG

  • All switches set to GND
  • Min -1.2 dB insertion loss

SW All 1s.PNG

References