RF Attenuators

From Land Boards Wiki
Jump to navigation Jump to search

Attenuator Charts

DBm vs Volta Watts.PNG

Chart mW vs dbM.PNG

Purchased Attenuators

PE4302 RF Attenuator

Homebrew RF Attenuators

Atten 30dB 20dV P1812-720px.jpg

30 dB Attenuator

Atten30dB P116-720px.jpg

30dB Attenuator.PNG

  • Built
    • Standard 5% resistor values
    • R1 = 820 in parallel with 22K = 790.6 ohms
    • R2 = 2 paralleled 120 Ohm 1/4W resistors paralleled with 470 ohms = 53.2 ohms
    • Flat from 0-30 MHz
    • Measured attenuation is flat
      • -30.01dB at 1 MHz
      • -30.24dB at 30 MHz
    • Input Impedance - 53.1 ohms, 21.3nF
    • SWR 1.06
    • 1/2W max (5VDC max, 0 ohm source)
  • NanoVNA scan data

30dB Attenuator NanoVNA Setup Curve 900MHz.PNG

30dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 30dB.PNG

20 dB Attenuator

Atten 20dB P115-720px.jpg

20dB Attenuator.PNG

  • Build
    • Standard 5% resistor values
    • R1 = 2 of 510 in parallel also in parallel with 8.2K = 247.3 ohms
    • R2 = 2 paralleled 150 Ohm 1/2W resistors paralleled with 330 ohms = 61.11 ohms
    • Flat from 0-30 MHz
    • Measured attenuation is flat
    • Input Impedance - tbd ohms, tbd nF
    • SWR tbd
    • 1W max (8.6 V max, 0 ohm source)

20dB Attenuator NanoVNA Setup Curve 900MHz.PNG

20dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 20dB.PNG

10 dB Attenuator

File:Atten 10dB P115-720px.jpg

10dB Attenuator.PNG

  • Build
    • Standard 5% resistor values
    • R1 = 2 of 150 in parallel also in parallel with 1.5K = 71.43 ohms (0.3% error)
    • R2 = 3 of 330 Ohm 1/4W parallel resistors paralleled with 810 ohms = 96.85 ohms (0.62% error)
    • Flat from 0-30 MHz
    • Measured attenuation is flat
    • Input Impedance - tbd ohms, tbd nF
    • SWR tbd
    • 3/4W max (9.1 V max, 0 ohm source)

File:10dB Attenuator NanoVNA Setup Curve 900MHz.PNG

File:10dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 10dB.PNG

Attenuator Construction

  • Single side copper clad PCB
    • Approx 2"x1"
  • Clean with steel wool
  • Solder SMA connectors
    • Use large alligator clips to hold while soldering
    • Solder on sides only

Atten 01 SMAs 720px.jpg

  • Cut "T" Shaped pads
    • I used nibbler
  • Center fits between connector ground pins
  • Glue down pads with Superglue

Atten 02 Pads 720px.jpg

  • Solder center pin with big solder blob
    • A bit too high for direct contact
  • Verify raised pad does not short to ground

Atten 03 Solder CenterPads 720px.jpg

  • Solder side resistor(s)
  • Leave room for center resistor(s)

Atten 04 Solder Side Resistors 720px.jpg

  • Measure side resistors from pad to ground
  • Should match value
  • Solder center resistor(s)

Atten 05 Solder Center Resistors 720px.jpg

  • Verify no shorts between centers and ground

References

  • Heavily inspired by Alan (W2AEW) video

W2AEW Attns-01.PNG

W2AEW Attns-02.PNG

W2AEW Attns-03.PNG