Difference between revisions of "Signal Generator"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 1: | Line 1: | ||
== Signal Generator from Stuff I've Already Made == | == Signal Generator from Stuff I've Already Made == | ||
| − | * [[NANO-BKOUT]] | + | * [[NANO-BKOUT]] |
| − | |||
| − | |||
| − | |||
* 2x [[NewPot2]] | * 2x [[NewPot2]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
* [[PulseGen]] | * [[PulseGen]] | ||
| − | * | + | * [[UNI-OPAMP-08]] |
| − | + | * AD9850 card | |
| − | * | + | * 0.96" pitch OLED card |
| − | * | ||
=== NANO-BKOUT === | === NANO-BKOUT === | ||
[[File:NANO-BKOUT-P1010078-800px.jpg]] | [[File:NANO-BKOUT-P1010078-800px.jpg]] | ||
| + | |||
| + | * Arduino NANO Breakout board | ||
| + | * 5V Power Regulator | ||
| + | * Probably don't need all the connectors | ||
| + | ** Why not just install them? | ||
| + | ** Good for 5V power/ground distribution | ||
| + | * USB connector | ||
| + | |||
| + | === NewPot2 === | ||
| + | |||
| + | * Use 2x boards for menu control | ||
| + | * Used as 0.1" pitch connector to Encoders | ||
| + | * Install R1-R3 = 10K | ||
| + | * Don't install ATTiny85 | ||
| + | * Don't install C1 | ||
| + | * Don't install D/A converter | ||
| + | |||
| + | ==== NewPot2 H1 Connector ==== | ||
| + | |||
| + | # Rotary Switch B | ||
| + | # VCC | ||
| + | # Unused | ||
| + | # Rotary Switch A | ||
| + | # Rotary Switch pushbutton | ||
| + | # GND | ||
| + | |||
| + | === PulseGen === | ||
| + | |||
| + | * Two boards | ||
| + | ** Use 1 to drive square wave on BNC to 50 Ohm load | ||
| + | *** Install BNC, 74AC14, 249 Ohm Series resistors | ||
| + | *** Don't install oscillator parts | ||
| + | ** Use other to connect to BNC for Sine Wave output | ||
| + | *** Only install BNC | ||
| + | |||
| + | === UNI-OPAMP-08 === | ||
| + | |||
| + | * Drive Sine Wave output | ||
| + | ** Route to PulseGen card for BNC use | ||
| + | * Use MCP6004 part | ||
| + | ** Disable all other channels | ||
Revision as of 13:38, 7 September 2020
Contents
Signal Generator from Stuff I've Already Made
- NANO-BKOUT
- 2x NewPot2
- PulseGen
- UNI-OPAMP-08
- AD9850 card
- 0.96" pitch OLED card
NANO-BKOUT
- Arduino NANO Breakout board
- 5V Power Regulator
- Probably don't need all the connectors
- Why not just install them?
- Good for 5V power/ground distribution
- USB connector
NewPot2
- Use 2x boards for menu control
- Used as 0.1" pitch connector to Encoders
- Install R1-R3 = 10K
- Don't install ATTiny85
- Don't install C1
- Don't install D/A converter
NewPot2 H1 Connector
- Rotary Switch B
- VCC
- Unused
- Rotary Switch A
- Rotary Switch pushbutton
- GND
PulseGen
- Two boards
- Use 1 to drive square wave on BNC to 50 Ohm load
- Install BNC, 74AC14, 249 Ohm Series resistors
- Don't install oscillator parts
- Use other to connect to BNC for Sine Wave output
- Only install BNC
- Use 1 to drive square wave on BNC to 50 Ohm load
UNI-OPAMP-08
- Drive Sine Wave output
- Route to PulseGen card for BNC use
- Use MCP6004 part
- Disable all other channels
