Difference between revisions of "Signal Generator"

From Land Boards Wiki
Jump to navigation Jump to search
 
(12 intermediate revisions by the same user not shown)
Line 58: Line 58:
 
** Disable all other channels
 
** Disable all other channels
  
== AD9850 Card ==
+
== AD9850 Card on GRID 49 Card ==
  
 
[[File:GRID49_PCB-3D.PNG]]
 
[[File:GRID49_PCB-3D.PNG]]
 +
 +
* [https://www.analog.com/media/en/technical-documentation/data-sheets/AD9850.pdf AD9850 Datasheet]
  
 
== Mechanicals ==
 
== Mechanicals ==
Line 70: Line 72:
 
** [[NANO-BKOUT]]
 
** [[NANO-BKOUT]]
 
** [[UNI-OPAMP-08]] or [[ANA-SIG-CON]]
 
** [[UNI-OPAMP-08]] or [[ANA-SIG-CON]]
** [https://www.aliexpress.com/af/ad9850.html?d=y&origin=n&SearchText=ad9850&catId=0&initiative_id=AS_20200907045511 AD9850 card] on
+
** [https://www.aliexpress.com/af/ad9850.html?d=y&origin=n&SearchText=ad9850&catId=0&initiative_id=AS_20200907045511 AD9850 card] on [[GRID49]] card
 +
* Front or Rear Panel
 +
* 2x [[PulseGen]] - could be stacked or bolted individually
 +
 
 +
== Software ==
 +
 
 +
* [http://www.vwlowen.co.uk/arduino/AD9850-waveform-generator/AD9850-waveform-generator.htm AD9850 Waveform Generator]
 +
 
 +
<video type="youtube">YFWZxhSAdpI</video>
 +
 
 +
[[File:AD9850-waveform-generator-circuit.png]]

Latest revision as of 14:32, 7 September 2020

Signal Generator from Stuff I've Already Made/Bought

NANO-BKOUT

NANO-BKOUT-P1010078-800px.jpg

  • Arduino NANO Breakout board
  • 5V Power Regulator
  • Probably don't need all the connectors
    • Why not just install them?
    • Good for 5V power/ground distribution
  • Install I2C connector
  • USB connector

NewPot2

NewPot2-6111-640px.jpg

  • Use 2x boards for menu control
  • Used as 0.1" pitch connector to Encoders
  • Install R1-R3 = 10K
  • Don't install ATTiny85
  • Don't install C1
  • Don't install D/A converter

NewPot2 H1 Connector

  1. Rotary Switch B
  2. VCC
  3. Unused
  4. Rotary Switch A
  5. Rotary Switch pushbutton
  6. GND

PulseGen

PulseGen 5242-720px.JPG

  • Two boards
    • Use 1 to drive square wave on BNC to 50 Ohm load
      • Install BNC, 74AC14, 249 Ohm Series resistors
      • Don't install oscillator parts
    • Use other to connect to BNC for Sine Wave output
      • Only install BNC

UNI-OPAMP-08

  • Drive Sine Wave output
    • Route to PulseGen card for BNC use
  • Use 100 MHz GBWP Op Amp
    • Disable all other channels

AD9850 Card on GRID 49 Card

GRID49 PCB-3D.PNG

Mechanicals

Software

AD9850-waveform-generator-circuit.png