Difference between revisions of "ER-PROTO-01"

From Land Boards Wiki
Jump to navigation Jump to search
 
(86 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/28599/]]
 +
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
  
Line 89: Line 91:
 
=== Arduino NANO MOZZI ===
 
=== Arduino NANO MOZZI ===
  
==== Controls ====
+
[[Arduino NANO MOZZI on ER-PROTO-01]]
 
 
* 6 Pots
 
** RV1 = Analog 7
 
** RV2 - Analog 4
 
** RV3 - Analog 6
 
** RV4 - Analog 3
 
** RV5 - Analog 5
 
** RV6 - Analog 2
 
* 2 CV Input Jacks
 
** J1 = Analog 0
 
** J2 = Analog 1
 
* 1 Output Jack
 
** J4 = MOZZI HI DEF Audio
 
 
 
==== Audio Out Schematic ====
 
 
 
[[FILE:ER-MOZZI-AUDIO_OUT_SCHEM.PNG]]
 
 
 
==== CV In Schematic ====
 
 
 
[[FILE:ER-MOZZI-CV_IN_SCHEM.PNG]]
 
 
 
==== Parts ====
 
 
 
* 3D view
 
 
 
[[FILE:ER-MOZZI-PARTS_3D.PNG]]
 
 
 
* Top parts view
 
  
[[FILE:ER-MOZZI-PARTS_DETAILS_TOP-3D.PNG]]
+
[[file:ER-PROTO-01-NANO-MOZZI_P1080687-720PX.jpg]]
  
* Bottom parts view
+
[[file:ER-PROTO-01-NANO-MOZZI_P1080693-720PX.jpg]]
  
[[FILE:ER-MOZZI-CV_IN_FILTER.PNG]]
+
=== CV4 - 4 Control Voltages ===
  
* CAD placement
+
[[ER-CVPOTS4]]
  
[[FILE:ER-MOZZI-PARTS_CAD.PNG]]
+
[[file:ER-PROTO-01-CV4_P1090031-F_B_720px.jpg]]
  
* With NANO
+
=== Noise Generator ===
  
[[FILE:ER-MOZZI-NANO_3D.PNG]]
+
[[Noise_Generator_on_ER-PROTO-01|Noise Generator on ER-PROTO-01]]
  
==== Wires ====
+
[[file:ER-PROTO-01_NOISE_P1080751-720px.jpg]]
  
<PRE>
+
[[file:ER-PROTO-01_NOISE_P1080755-720px.jpg]]
NET: +5VD, A1-27, J37-11
 
NET: ANA0, A1-19, C7-1, D1-2, D3-1, R9-2
 
NET: ANA1, A1-20, C8-1, D2-2, D4-1, R10-2
 
NET: ANA2, A1-21, C1-1, J37-3
 
NET: ANA3, A1-22, C2-1, J37-6
 
NET: ANA4, A1-23, C3-1, J37-9
 
NET: ANA5, A1-24, C4-1, J37-12
 
NET: ANA6, A1-25, C5-1, J37-15
 
NET: ANA7, A1-26, C6-1, J37-18
 
NET: J1-T, J10-8, J38-1, R7-1, R9-1
 
NET: J2-S, J10-1, J10-3, J10-5, J10-7
 
NET: J2-T, J10-4, J38-5, R10-1, R8-1
 
NET: J3-T, J10-6, J38-3
 
NET: J4-T, C10-1, J10-2, J38-7, R14-2
 
NET: GND, J37-7, J38-6
 
NET: Net-(J37-Pad4), J37-16, J37-4
 
NET: Net-(J37-Pad14), J37-14, J37-8
 
</PRE>
 
  
==== Parts List ====
+
=== Slew Rate Controller ===
  
{| class="wikitable"
+
[[Slew Rate Controller on ER-PROTO-01]]
! Find
 
! Qty
 
! Ref Des
 
! Part Number
 
|-
 
| 1
 
| 2
 
| R7, R8
 
| 100K
 
|-
 
| 2
 
| 2
 
| R9, R10
 
| 10K
 
|-
 
| 3
 
| 2
 
| R11, R14
 
| 3.9K
 
|-
 
| 4
 
| 2
 
| R12, R13
 
| 1M
 
|-
 
| 5
 
| 4
 
| D1-D4
 
| BAT41
 
|-
 
| 6
 
| 8
 
| C1-C8
 
| 0.1uF
 
|-
 
| 7
 
| 1
 
| C9
 
| 4.7nF
 
|-
 
| 8
 
| 1
 
| C10
 
| 10nF
 
|-
 
| 9
 
| 1
 
| J5
 
| HEADER, 2X10
 
|-
 
| 10
 
| 1
 
| J6
 
| [https://store.synthrotek.com/16-Pin_Keyed_Shrouded_Eurorack_Power_Header HEADER, 2X8]
 
|-
 
| 11
 
| 1
 
| J10
 
| HEADER, 1x8
 
|-
 
| 12
 
| 1
 
| A1
 
| Arduino_Nano_v3
 
|-
 
|}
 
  
=== Arduino NANO with quad Opamp example ===
+
== Assembly Sheet ==
  
[[file:ER-PROTO-DB-01_ARDUINO_NANO_OPAMP-720px.png]]
+
* [[ER-PROTO-01 Assembly Sheet]]

Latest revision as of 17:48, 18 January 2023

Tindie-mediums.png

ER-PROTO-PANEL-01-SET FRONT REAR-3D-720px.png

Features

  • Eurorack Prototyping card set
  • 6 HP wide (30mm) front panel
  • 3U tall
  • Three card set
    • Board interconnect headers duplicated on headers
    • 30mm wide front panel
    • 28mm wide panel and daughtercards
  • 6 POTS
    • Marked as RV1-RV5
    • Series resistors on pot wiper
    • All 3 pot pins brought to top header
  • 4 Jacks
    • Marked as J1-J4
    • Tip/sleeve brought to header near middle/bottom
  • Pots on top, jacks on bottom of card
    • Easier to adjust pots without bumping into pots
    • Pots more often accessed than jacks
  • Large prototyping area
    • 58 nodes with 3 holes per node (29 per "side")
  • +12V, -12V down board edges
  • 5V/GND down center of card
  • Bussed connections horizontally
  • Front Panel with generic labels
    • Cover with White on Black P-Touch labels

Connectors

  • J1-J4 are front panel connectors

Inter-card Connectors

Pots

  • J5 on the Controls card and J5 on the I/O card
  • Pot connections
    • POTx-1 is fully CW connects to wiper
    • POTx-2 is wiper
    • POTX-3 is fully CCW connects to wiper

RV Conns.PNG

  • To make pot into voltage control
    • POTx-1 (CW) = +5V
    • POTx-13CCW = GND
    • Wire RV1-1 to RV3-1 to RV5-1 on controls card
    • Wire RV1-3 to RV3-3 to RV5-3 on controls card
    • Wire RV2-1 to RV4-1 to RV6-1 on controls card
    • Wire RV2-3 to RV4-3 to RV6-3 on controls card

ER-PROTO-CTLS-6-01 J5.PNG

Jacks

  • J6 on the controls card and J37 on the I/O card

ER-PROTO-CTLS-6-01 J10.PNG

Daughtercard Connectors

J5, J37 - POT connectione

ER-PROTO-DB-01 J5.png

ER-PROTO-DB-01 J37.png

J6 - Eurorack Power

  • J6 on the I/O card
    • Eurorack power
    • 2x5 IDC
    • GATE, CV not connected

ER-PROTO-DB-01 J6.png

J10 - Jacks connections on Controls card

ER-PROTO-DB-01 J10.png

J38 - Jacks connections

ER-PROTO-DB-01 J38.png

Examples

Arduino NANO MOZZI

Arduino NANO MOZZI on ER-PROTO-01

ER-PROTO-01-NANO-MOZZI P1080687-720PX.jpg

ER-PROTO-01-NANO-MOZZI P1080693-720PX.jpg

CV4 - 4 Control Voltages

ER-CVPOTS4

ER-PROTO-01-CV4 P1090031-F B 720px.jpg

Noise Generator

Noise Generator on ER-PROTO-01

ER-PROTO-01 NOISE P1080751-720px.jpg

ER-PROTO-01 NOISE P1080755-720px.jpg

Slew Rate Controller

Slew Rate Controller on ER-PROTO-01

Assembly Sheet