Difference between revisions of "ER-MIDI-CV4-02"

From Land Boards Wiki
Jump to navigation Jump to search
 
(33 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/28969/]]
 +
 
[[FILE:ER-MIDI-CV4-02_P1080867-720px.jpg]]
 
[[FILE:ER-MIDI-CV4-02_P1080867-720px.jpg]]
  
Line 10: Line 12:
 
** Processor card
 
** Processor card
 
* [[Arduino_Pro_Mini|Arduino Pro Mini]]
 
* [[Arduino_Pro_Mini|Arduino Pro Mini]]
 +
** Either ATMega168 or ATMega328
 
** 16 MHz
 
** 16 MHz
 
** 5V
 
** 5V
Line 25: Line 28:
 
* CLK output (0-5V)
 
* CLK output (0-5V)
 
* TRIG output (0-5V)
 
* TRIG output (0-5V)
* Standard Eurorack 16 pin power header
+
* Standard Eurorack 10 pin power header
  
 
=== Credits ===
 
=== Credits ===
Line 182: Line 185:
 
* MIDI Input
 
* MIDI Input
 
* TRS Type A
 
* TRS Type A
 +
 +
[[FILE:ER-MIDI-CV4_J8.PNG]]
 +
 +
===== MIDI TRS A =====
 +
 +
* From [https://minimidi.world/ minimidi.world]
 +
* DIN
 +
 +
[[file:MINIMIDI_WORLD_DIN.PNG]]
 +
 +
* TRS A
 +
 +
[[file:MINIMIDI_WORLD_TYPE-A.PNG]]
  
 
==== J9 - MIDI Out ====
 
==== J9 - MIDI Out ====
Line 200: Line 216:
 
* Card test code
 
* Card test code
 
* Basic Application
 
* Basic Application
* Drum Triggers Application
+
* Polyphonic/Drum Triggers Application
 +
 
 +
=== Programming ===
 +
 
 +
* Program with FTDI Serial
 +
* FTDI set to 5V signal levels
 +
* Cable does not connect VCC
 +
 
 +
[[file:ER-MIDI-CV4-02_P1080860-720px.jpg]]
 +
 
 +
*  Unplug MIDI in cable from front panel
 +
*  Connect FTDI card with 1:1 cable
 +
*  Download code in Arduino IDE
 +
*  Disconnect FTDI
 +
*  Connect MIDI in cable to front panel
  
 
=== Card Test Code ===
 
=== Card Test Code ===
  
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/TestPotDigIOs/TestPotDigIOs.ino TestPotDigIOs] - Test Digital Outputs (CLK, TRIG, GATE) and Speed Pot
+
* Code useful to verify card is correctly assembled
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/ER_MIDI_CV4_04_TEST_DACs/ER_MIDI_CV4_04_TEST_DACs.ino ER_MIDI_CV4_04_TEST_DACs] - Read pot, scale value. write to 4 analog outputs. Also, drive CLK, TRIG, GATE digital outputs
+
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/TestPotDigIOs/TestPotDigIOs.ino TestPotDigIOs]
 +
** Test Digital Outputs (CLK, TRIG, GATE) and Speed Pot
 +
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/ER_MIDI_CV4_04_TEST_DACs/ER_MIDI_CV4_04_TEST_DACs.ino ER_MIDI_CV4_04_TEST_DACs]
 +
** Read pot, scale value. write to 4 analog outputs
 +
** Also, drive CLK, TRIG, GATE digital outputs
 +
 
 +
=== HAGIWO code baseline ===
 +
 
 +
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/SYNTHMIDICTL01/SYNTHMIDICTL01.ino SYNTHMIDICTL01.ino]
 +
** Runs on Arduino ATMEGA328 (Arduino NANO or Pro Mini)
 +
** Used as baseline and converted to CircuitPython
  
 
=== Basic Application===
 
=== Basic Application===
  
 +
* [https://github.com/land-boards/lb-Arduino-Code/tree/master/LBCards/SYNTHS/ER_MIDI_CV/ER_MIDI_CV4_02 ER_MIDI_CV4_02] - Base application
 
* Listens on channel 0
 
* Listens on channel 0
 
** CV1 controls pitch
 
** CV1 controls pitch
* Use with [[ER-VCO-03]] to control pitch and Mod
+
* Ex: Use with [[ER-VCO-03]] to control pitch and Mod
 
** CV_1 = V/OCT
 
** CV_1 = V/OCT
 
** CV_2 = MOD
 
** CV_2 = MOD
Line 218: Line 259:
 
* [https://www.inspiredacoustics.com/en/MIDI_note_numbers_and_center_frequencies MIDI Notes]
 
* [https://www.inspiredacoustics.com/en/MIDI_note_numbers_and_center_frequencies MIDI Notes]
  
==== HAGIWO code baseline ====
+
=== Polyphonic and Drum Triggers Code ===
 
 
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/SYNTHMIDICTL01/SYNTHMIDICTL01.ino SYNTHMIDICTL01.ino]
 
** Runs on Arduino ATMEGA328 (Arduino NANO or Pro Mini)
 
** Used as baseline and converted to CircuitPython
 
 
 
==== Working Code ====
 
  
 
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/ER_MIDI_CV4_02/ER_MIDI_CV4_02.ino ER_MIDI_CV4_02] - Working code
 
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/ER_MIDI_CV/ER_MIDI_CV4_02/ER_MIDI_CV4_02.ino ER_MIDI_CV4_02] - Working code
 
+
* #define for polyphonic and drum modes
 +
** #define POLYPHONIC uses CV1-4, a single gate output
 +
** #define DRUM_TRIGGER_OUTS uses TRIG and CLK to trigger drums Beaks (Peaks)
 
<pre>
 
<pre>
 
// V/OCT LSB for DAC
 
// V/OCT LSB for DAC
Line 246: Line 283:
 
</pre>
 
</pre>
  
=== Download steps ===
+
=== Drum Controller Application ===
  
* Unplug MIDI in cable from front panel
+
* Use TRIG and GATE output jacks to drive [[Beaks_Through_Hole_Peaks|Beaks]] in Drum mode
* Connect FTDI card with 1:1 cable
+
* Re-label Gate as TRIG 2 on Front Panel
* Download code in Arduino IDE
+
* Using USB MIDI as MIDI source
* Disconnect FTDI
+
** [[ER-USB-MIDI]] through [[ER-MIDI-THRU]] into MIDI In on this card
* Connect MIDI in cable to front panel
+
*** Set [[ER-USB-MIDI]] to pass all channels
 +
** [[ER-MIDI-THRU]] always passes all channels
 +
** Keyboard off or unplugged from [[ER-MIDI-THRU]]
 +
* Using keyboard as MIDI source
 +
** Keyboard plugged into [[ER-MIDI-THRU]]
 +
** [[ER-MIDI-THRU]] not plugged into ER-MIDI-CV4-02
 +
* Uses 2 ER-MIDI-CV4-02 card sets
 +
** One ER-MIDI-CV4-02 card set to listen on MIDI Channel 1
 +
** Second ER-MIDI-CV4-02 card set to listen to Drums on Channel 10
 +
* [https://www.midi.org/specifications-old/item/gm-level-1-sound-set GM 1 Sound Set]
  
=== Drum Controller Application ===
+
==== Drum Controller Build notes ====
  
* Use Trig and GATE outputs to drive [[Beaks_Through_Hole_Peaks|Beaks]] in Drum mode
+
* Do not populate D/A converter
* [[ER-USB-MIDI]] through [[ER-MIDI-THRU]] into MIDI In on this card
+
* Do not populate CV jacks
* Drums are on Channel 10
+
* Do not populate related discrete parts
  
 
== 3D Views ==
 
== 3D Views ==
Line 281: Line 327:
  
 
== Issues ==
 
== Issues ==
 +
 +
[[file:ER-MIDI-CV4-02_P1080869-720px.jpg]]
  
 
=== Rev 2 ===
 
=== Rev 2 ===

Latest revision as of 03:36, 10 January 2023

Tindie-mediums.png

ER-MIDI-CV4-02 P1080867-720px.jpg

Features

  • Eurorack 6HP, 3U module
  • Three card stack-up
    • Front Panel card
    • Controls card
      • 9 Jacks, 1 pot
    • Processor card
  • Arduino Pro Mini
    • Either ATMega168 or ATMega328
    • 16 MHz
    • 5V
    • Programmed via Serial
  • MIDI In
    • TRS Type A jack MIDI In
    • USB MIDI In if external FTDI card/cable
  • (4) 0-4.096V Analog CV outs
  • GATE output (0-5V)
  • CLK output (0-5V)
  • TRIG output (0-5V)
  • Standard Eurorack 10 pin power header

Credits

Arduino Pins

  • Arduino Pro Mini
  • Analog 1 - Speed Adjust POT
  • A4 = SDA
  • A5 = SCL
  • D8 = LDAC1* to CV_1, CV2
  • D9 = LDAC2* to CV_3, CV_4
  • D13 = SPI CSK to both ADCs
  • D11 = SPI MOSI to both ADCs
  • D10 = SLAVE SELECT to both ADCs

ArdruinoProMini-EBAY PART-720px.png

Connection to FTDI

  • Use FTDI-49MM card
  • Right angle 1x6 pins
  • Pinout
  1. GND
  2. CTSn (IN)
  3. VCC
  4. TX (OUT)
  5. RX (IN)
  6. RTSn (OUT)
  • Arduino Pro Mini Serial Connector
  • Marking matches FTDI cable pinouts/color codes

FTDI Cable Color Code.png

  1. BLK
  2. GND
  3. VCC
  4. RX
  5. TX
  6. GRN

Connectors

Processing Card Connectors

J1 - Eurorack Power

ER-MIDI-CV4-02 DB J1.PNG

  • 2x5 IDC connector
  • Only uses +12V (and GND)
  • Diode polarity protected, series resistor

J2 - CVs, GATE, CLK (to/from Controls card)

ER-MIDI-CV4-02 DB J2.PNG

  • J12 on Controls card
  • Pinout
  1. VCC (+5V)
  2. GATE
  3. CLK
  4. CV4
  5. CV2
  6. POT
  7. CV1
  8. CV3
  9. TRIGGER
  10. GND

J3 - I2C

ER-MIDI-CV4-02 DB J3.PNG

  • Pinout
  1. SCL
  2. SDA
  3. VCC (+5V)
  4. GND

J4 - MIDI (to/from Controls card)

ER-MIDI-CV4-02 DB J4.PNG

  • J9 on Controls card
  • Pinout
  1. VCC (+5V)
  2. MIDI Out
  3. MIDI In
  4. GND

J5 - MIDI into RX

ER-MIDI-CV4-02 DB J5.PNG

  • Remove to use MIDI from Controls card

J6 - MIDI OUT/THRU Select

ER-MIDI-CV4-02 DB J6.PNG

  • 1-2 = MIDI Thru
  • 2-3 = MIDI out from Arduino TX

Controls Card Connectors

J1 - CLK

  • MIDI Clock out
  • 0-5V, Digital

J2 - CV1 Out

  • Control Voltage out
  • 0-5V Analog Clock

J3 - CV2 Out

  • Control Voltage out
  • 0-5V Analog Clock

J4 - CV3 Out

  • Control Voltage out
  • 0-5V Analog Clock

J5 - CV4 Out

  • Control Voltage out
  • 0-5V Analog Clock

J6 - TRIGGER

  • MIDI Trigger out
  • 0-5V, Digital

J7 - GATE

  • MIDI Gate out
  • 0-5V, Digital

J8 - MIDI In

  • MIDI Input
  • TRS Type A

ER-MIDI-CV4 J8.PNG

MIDI TRS A

MINIMIDI WORLD DIN.PNG

  • TRS A

MINIMIDI WORLD TYPE-A.PNG

J9 - MIDI Out

  • MIDI Output
  • TRS Type A

J10 - CVs, GATE, CLK, TRIG

ER-MIDI-CV4-CTLS J10.PNG

J11 - MIDI

ER-MIDI-CV4-CTLS J11.PNG

Applications

  • Card test code
  • Basic Application
  • Polyphonic/Drum Triggers Application

Programming

  • Program with FTDI Serial
  • FTDI set to 5V signal levels
  • Cable does not connect VCC

ER-MIDI-CV4-02 P1080860-720px.jpg

  • Unplug MIDI in cable from front panel
  • Connect FTDI card with 1:1 cable
  • Download code in Arduino IDE
  • Disconnect FTDI
  • Connect MIDI in cable to front panel

Card Test Code

  • Code useful to verify card is correctly assembled
  • TestPotDigIOs
    • Test Digital Outputs (CLK, TRIG, GATE) and Speed Pot
  • ER_MIDI_CV4_04_TEST_DACs
    • Read pot, scale value. write to 4 analog outputs
    • Also, drive CLK, TRIG, GATE digital outputs

HAGIWO code baseline

  • SYNTHMIDICTL01.ino
    • Runs on Arduino ATMEGA328 (Arduino NANO or Pro Mini)
    • Used as baseline and converted to CircuitPython

Basic Application

Polyphonic and Drum Triggers Code

  • ER_MIDI_CV4_02 - Working code
  • #define for polyphonic and drum modes
    • #define POLYPHONIC uses CV1-4, a single gate output
    • #define DRUM_TRIGGER_OUTS uses TRIG and CLK to trigger drums Beaks (Peaks)
// V/OCT LSB for DAC
// ER-VCO-03 characteristics
//  PITCH ADJ knob roughly centered
//  0V = 93.08 Hz (roughly F2)
//  1V = 179 Hz (G3)
//  1.52V = 261 Hz (C4)
//  2V = 365 Hz (G4)
//  3V = 722 Hz (G5)
//  4V = 1.45 KHz (G6)
//  5V = 3.05 KHz (G7)
// Max output voltage of this card is 4.096V (4 octaves)
//  1mV per DAC count
// 12 notes per octave = 1/12V per note = 83.333 mV
// Steps are in 83.333 mV
// Table counts up by integer steps - rounded 83.333 mV

Drum Controller Application

  • Use TRIG and GATE output jacks to drive Beaks in Drum mode
  • Re-label Gate as TRIG 2 on Front Panel
  • Using USB MIDI as MIDI source
  • Using keyboard as MIDI source
  • Uses 2 ER-MIDI-CV4-02 card sets
    • One ER-MIDI-CV4-02 card set to listen on MIDI Channel 1
    • Second ER-MIDI-CV4-02 card set to listen to Drums on Channel 10
  • GM 1 Sound Set

Drum Controller Build notes

  • Do not populate D/A converter
  • Do not populate CV jacks
  • Do not populate related discrete parts

3D Views

  • Controls card side view

ER-MIDI-CV4-02 CTLS SIDE-3D.png

  • Processing card side view

ER-MIDI-CV4-02 DB SIDE 3D.png

Videos

  • HAGIWO MIDI to CV module

  • Midi2CV - A utility module for converting MIDI messages to CV] Benjie Jiao - DIY Modular Synth Project_

Issues

ER-MIDI-CV4-02 P1080869-720px.jpg

Rev 2

  • Daughtercard
    • Fixed missing connection D14 anode to GND
    • Moved R1 down a bit
    • Haven't ordered yet (2022-12-04)

Rev 1

  • Daughtercard
    • Missing connection D14 anode to GND
      • Add wire D14-Anode to D9-Anode
    • R1 is close to Arduino socket (fit OK, but tight)

Assembly Sheet