SIMPLE-68008

Features

• 68008 CPU
  • 20 bit address space (1MB total)
• 10 MHz clock
• Up to 512KB SRAM
• Up to 512KB EPROM/EEPROM
• 68681 Dual Serial Port (ACIA)
  • Headers for FTDI
  • 38,400 baud
• Reset switch with optional Power Supervisor
• 95x95mm card
• (4) 6-32 mounting holes

Memory Map

• The memory map depends on two things
  • Mapping in the PLDs
  • The firmware that is being run on the card

Maximal Capacity Design

• 0x00000-0x7FFFF 512KB SRAM
• 0x80000-0xEFFFF Up to 448KB EPROM (minus DUART I/O space)
• 0xF0000-0xFFFFF Serial (ACIA)

Chip Set

• On Ebay

Parts in "Kit"

• MC68000P10 - 68K CPU with 16-bit data bus and 24-bit address bus
• MC68230P8 - Parallel I/O bits, timer
• TMP68681P - Dual UART, 8-bit I/O, 6-bit I/O
• MC68901P - Multifunction (8 I/O pins, interrupt controller, (4) timers, UART
• AM8511A - Floating Point Unit
• MC68008P10 - 68K CPU with 8-bit data bus and 20-bit address bus
• 65B50P - ACIA (Serial interface)

Design

CPU

The Motorola 68008 is an 8/32-bit microprocessor introduced by Motorola in 1982. It is a version of 1979's Motorola 68000 with an 8-bit external data bus, as well as a smaller address bus. The 68008 was available with 20 address lines (48-pin package) which allowed 1 MB address space versus the 16 MB addressable on the 68000.

CPU Timing

Function Code

EPROM

• SST27C256 EEPROM
  • 32 KB part
  • 28 pin part, 32 pin socket

EEPROM Programming

• Program using TL-866ii plus programmer
• File = TBD
• Set offsets for 27SF256 part
  • Part is 32 KB
  • hex files is 16 KB
• Set From File Start Addr(Hex) to 0C000
• To Buffer Start Addr(Hex) to 00000

TBD

• Memory Buffer should look like

TBD

• Got Device ID error
• Turn off ID check

TBD

• Device programmed/verified

SRAM

Dual UART

Reset

Clock

PLDs

• Two ATF16V8B PLDs (Datasheet)
• WinCupl compiler
  • WinCupl Download link

PLD_001

Name       SIMPLE-68008_PLD_1;
Partno     ATF16V8B;
Date       09/14/22;
Revision   01;
Designer   DOUG G;
Company    LAND BOARDS LLC;
Assembly   U02;
Location   RUSTBELT, USA;
Device     G16V8;

/*
*/

/* Inputs */
PIN    1   = CLK;
PIN    2   = !CPUAS;
PIN    3   = !CPUDS;
PIN    4   = CPUA16;
PIN    5   = CPUA17;
PIN    6   = CPUA18;
PIN    7   = CPUA19;
PIN    8   = CPUFC0;
PIN    9   = CPUFC1;
PIN    11  = CPUFC2;
PIN    12  = !DDTACK;
PIN    13  = SWAP;

/* Outputs */
PIN    14  = !CPUIACK;
PIN    15  = !DUARTCS;
PIN    16  = !CPUDTACK;
PIN    17  = WAIT1;
PIN    18  = !RAMSEL;
PIN    19  = WAIT2;

CPUIACK = CPUFC2 & CPUFC1 & CPUFC0 & CPUDS;

DUARTCS = CPUA19 & CPUA18 & CPUA17 & CPUA16 & CPUDS & !CPUFC1 &  CPUFC0;

RAMSEL = !CPUA19 & SWAP & CPUDS & !CPUFC1 &  CPUFC0  /* User/Super Data */
#        !CPUA19 & SWAP & CPUDS &  CPUFC1 & !CPUFC0; /* User/Super Program */

CPUDTACK =  CPUA19 & CPUA18 & CPUA17 & CPUA16 & CPUDS & DDTACK	/* DUART	*/
#           CPUA19 & !CPUA18 & CPUDS											/* EPROM	*/
#           CPUA19 & !CPUA17 & CPUDS											/* EPROM	*/
#           CPUA19 & !CPUA16 & CPUDS											/* EPROM	*/
#          !CPUA19 & CPUDS;															/* RAM 		*/

PLD_002

Name       SIMPLE-68008_PLD_2;
Partno     ATF16V8B;
Date       06/19/24;
Revision   01;
Designer   DOUG G;
Company    LAND BOARDS LLC;
Assembly   U03;
Location   RUSTBELT, USA;
Device     G16V8;

/*
	RESET CONTROLLER, ROM CHIP SELECT
*/

/* Inputs */
PIN    1   = CLK;
PIN    2   = !CPUWR;
PIN    3   = !CPUDS;
PIN    4   = CPUA16;
PIN    5   = CPUA17;
PIN    6   = CPUA18;
PIN    7   = CPUA19;
PIN    8   = !POR;
PIN    9   = CPUD0;

/* Outputs */
PIN    14  = SWAP;
PIN    15  = !ROMCS;
PIN    16  = !MEMRD;
PIN    18  = !CPUHLT;
PIN    19  = !CPURES;

/* CLEAR SWAP AT POWER UP, RESET	*/
/* SET SWAP BY FIRST WRITE TO START OF EPROM SPACE		*/
SWAP.D = CPUDS &  CPUWR & CPUA19 & !CPUA18 & !CPUA17 & !CPUA16 & CPUD0 & !POR
#        SWAP  & !POR;

MEMRD = !CPUWR & CPUDS & !CPUA19 & SWAP;

ROMCS = CPUDS & !CPUWR & CPUA19 & !CPUA18
#       CPUDS & !CPUWR & CPUA19 & !CPUA17
#       CPUDS & !CPUWR & CPUA19 & !CPUA16
#       CPUDS & !CPUA19 & !CPUA18 & !CPUA17 & !CPUA16 & !SWAP;

CPUHLT_N.OE = POR;
CPUHLT_N = POR;

CPURES_N.OE = POR;
CPURES_N = POR;

Headers / Connectors

J1 - 2 port FTDI / TTL Serial

• 2x6 header
• Direct connect to DTE RS-232 card
• Flip order to connect to USB to TTL Serial (FTDI)
  • TX<>RX
  • RTS<>CTS
• Pinout

1. GND
2. CTS* (in)
3. +5V
4. Transmit (out)
5. Receive (in)
6. RTS* (out)

J2 - Input Port

1. Input 2
2. Input 5
3. Input 4
4. Input 3
5. Vcc
6. GND

J3 - Output Port

1. GND
2. Vcc
3. Output 7
4. Output 6
5. Output 5
6. Output 4
7. Output 3
8. Output 2

H1 - 5V Power

• 2x4 header

H3-H5 - EPROM/EEPROM Select Jumpers

• H2 = EE PIN 31
• H3 = EE PIN 3
• H4 = EE PIN 30
• H5 = EE PIN 29

27040	27020	27010	27512	27256	27128	2764	PIN(32)	PIN(28)		PIN(28)	PIN(32)	2764	27128	27256	27512	27010	27020	27040
VPP	VPP	VPP	N/A	N/A	N/A	N/A	1	N/A		N/A	32	N/A	N/A	N/A	N/A	VCC	VCC	VCC
A16	A16	A16	N/A	N/A	N/A	N/A	2	N/A		N/A	31 (H2)	N/A	N/A	N/A	N/A	PGM	PGM	A18
A15	A15	A15	A15	VPP	VPP	VPP	3 (H3)	1		28	30 (H4)	VCC	VCC	VCC	VCC	N/C	A17	A17
A12	A12	A12	A12	A12	A12	A12	4	2		27	29 (H5)	PGM	PGM	A14	A14	A14	A14	A14
A7	A7	A7	A7	A7	A7	A7	5	3		26	28	A13	A13	A13	A13	A13	A13	A13
A6	A6	A6	A6	A6	A6	A6	6	4		25	27	A8	A8	A8	A8	A8	A8	A8
A5	A5	A5	A5	A5	A5	A5	7	5		24	26	A9	A9	A9	A9	A9	A9	A9
A4	A4	A4	A4	A4	A4	A4	8	6		23	25	A11	A11	A11	A11	A11	A11	A11
A3	A3	A3	A3	A3	A3	A3	9	7		22	24	OE*	OE*	OE*	OE*	OE*	OE*	OE*
A2	A2	A2	A2	A2	A2	A2	10	8		21	23	A10	A10	A10	A10	A10	A10	A10
A1	A1	A1	A1	A1	A1	A1	11	9		20	22	CE*	CE*	CE*	CE*	CE*	CE*	CE*
A0	A0	A0	A0	A0	A0	A0	12	10		19	21	D7	D7	D7	D7	D7	D7	D7
D0	D0	D0	D0	D0	D0	D0	13	11		18	20	D6	D6	D6	D6	D6	D6	D6
D1	D1	D1	D1	D1	D1	D1	14	12		17	19	D5	D5	D5	D5	D5	D5	D5
D2	D2	D2	D2	D2	D2	D2	15	13		16	18	D4	D4	D4	D4	D4	D4	D4
GND	GND	GND	GND	GND	GND	GND	16	14		15	17	D3	D3	D3	D3	D3	D3	D3

Software

• TUTOR 1.2 Monitor
  • Addressing issues due to code being designed for ROM at below 64K

Linux Development Environment

• Using Oracle VM VirtualBox
• Running Linux Mint
• The GNU C-Compiler with Binutils and other useful tools for 68000 cross development
• This is a Makefile based approach to build the toolchain to reduce the build time.
• The original work was by Steve Moody Moody's page
• These tools are build:
  • binutils
  • gcc with libs for C/C++/ObjC
  • vasm
  • vbcc
  • vlink
  • newlib

Mechanicals

Assembly Sheet

Rev 1

• SIMPLE-68008 Rev 1 Assembly Sheet
• SIMPLE-68008 Rev 1 Interactive BOM