Difference between revisions of "DRIVE50"

From Land Boards Wiki
Jump to navigation Jump to search
 
(30 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[file:DRIVE50_FRONT_3D.png]]
+
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/5075-ohm-ttl-line-driver/]]
 +
 
 +
[[file:DRIVE50_P1080480-720PX.jpg]]
  
 
== 50 Ohm Driver Card ==
 
== 50 Ohm Driver Card ==
Line 8: Line 10:
 
* 10K pull-up on input
 
* 10K pull-up on input
 
* Card is non-inverting
 
* Card is non-inverting
−
* 3V-5V power
+
* 1.5V-5.5V power
 +
** Typically 3.3V or 5V
 
* 3-pin right angle 0.1" pitch input connector
 
* 3-pin right angle 0.1" pitch input connector
 
* (4) 4-40 mounting holes
 
* (4) 4-40 mounting holes
Line 14: Line 17:
 
=== Driver ===
 
=== Driver ===
  
−
* 5x paralleled [http://cva.stanford.edu/classes/cs99s/datasheets/74AC14.pdf 74AC14] drivers
+
* 5x paralleled [https://www.ti.com/lit/ds/symlink/cd74ac14.pdf?HQS=dis-mous-null-mousermode-dsf-pf-null-wwe&ts=1658486403853&ref_url=https%253A%252F%252Fwww.mouser.com%252F 74AC14] drivers
 
** 24mA per pin max current output
 
** 24mA per pin max current output
 +
*** Symmetric high-low drive levels
 
** Short-circuit proof
 
** Short-circuit proof
−
*** 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA
+
*** 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA)
 +
*** 0.125 W resistor (5V output through 249 ohm resistor with output shorted to ground is 0.1 W)
 +
*** 3.3V, 250 Ohms to ground is 13.2 mA (pins are rated for 24 mA)
 +
*** 0.125 W resistor (3.3V output through 249 ohm resistor with output shorted to ground is 0.044 W)
 +
* Card has input buffer stage
 
* Schmitt Trigger Input
 
* Schmitt Trigger Input
−
* Input has single buffer stage
 
 
* 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
 
* 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
 
** Normal output = 10 mA per pin
 
** Normal output = 10 mA per pin
  
 
== Test ==
 
== Test ==
 +
 +
* Manual or Automated test methods
 +
 +
=== Manual Test Method ===
  
 
* Supply Vcc 3.3V to 5V and ground
 
* Supply Vcc 3.3V to 5V and ground
Line 30: Line 41:
 
** Should be 1/2 of Vcc with 50 Ohm terminator
 
** Should be 1/2 of Vcc with 50 Ohm terminator
 
** Should be Vcc without terminator
 
** Should be Vcc without terminator
 +
 +
=== Automated Test Software Method ===
 +
 +
[[File:DRIVE50_P1080485-720PX.jpg]]
 +
 +
==== Setup ====
 +
 +
* [[QTPy49]] or [[QTPy49-01]] card
 +
* [[QT Py (RP2040_based)]] card
 +
** Analog cable
 +
** GVS Cable to A1
 +
** Analog in (BNC) to A0 on [[QTPy49]]
 +
* [[MyMenu]] card
 +
* Power card options
 +
** Connect USB-C to the [[QT Py (RP2040 based)]] or
 +
** Power from 9-12V to DC jack
 +
* Terminator - dependent on build option
 +
** 50 Ohms
 +
** 75 Ohms
 +
* Unit Under Test (UUT)
 +
* [https://github.com/land-boards/QT-Py/blob/main/CircuitPython/lbcards/PulseGen/PulseGen_DRIVE50_Test.py PulseGen_DRIVE50_Test.py]
 +
** Test software for [[PulseGen]] and DRIVE50 cards
 +
*** Auto-detects card type
 +
** Stored as code.py on [[QT Py (RP2040 based)]] to auto-run
 +
 +
==== Procedure ====
 +
 +
* Connect 3 pin power cable to card
 +
* Connect BNC T to output of card
 +
* Connect BNC female from tester to BNC T male
 +
* Install 50 terminator to other side of BNC T
 +
* Connect USB C cable
 +
* Display will show
 +
 +
<pre>
 +
PulseGen/DRIVE50 V1.1
 +
50 Ohm card
 +
Set/Got Low
 +
Term High = OK
 +
</pre>
 +
 +
* All 3 LEDs are on
 +
 +
== Application Example ==
 +
 +
=== GPS Frequency Standard ===
 +
 +
[[file:GPS_Freq_Std_P18490-720px.jpg]]
 +
 +
* [[GPS_Frequency_Standard|GPS Frequency Standard]]
 +
* Card takes in PPS signal out of GPS module and drives 50 Ohm, 10 MHz Frequency Standard output on coax via BNC connector
  
 
== Mechanicals ==
 
== Mechanicals ==

Latest revision as of 11:25, 20 August 2022

Tindie-mediums.png

DRIVE50 P1080480-720PX.jpg

50 Ohm Driver Card

  • "TTL" Level Line driver
  • 50 or 75 Ohm output impedance
  • BNC or SMA output connector
  • 10K pull-up on input
  • Card is non-inverting
  • 1.5V-5.5V power
    • Typically 3.3V or 5V
  • 3-pin right angle 0.1" pitch input connector
  • (4) 4-40 mounting holes

Driver

  • 5x paralleled 74AC14 drivers
    • 24mA per pin max current output
      • Symmetric high-low drive levels
    • Short-circuit proof
      • 5V, 250 Ohms to ground is 20 mA (pins are rated for 24 mA)
      • 0.125 W resistor (5V output through 249 ohm resistor with output shorted to ground is 0.1 W)
      • 3.3V, 250 Ohms to ground is 13.2 mA (pins are rated for 24 mA)
      • 0.125 W resistor (3.3V output through 249 ohm resistor with output shorted to ground is 0.044 W)
  • Card has input buffer stage
  • Schmitt Trigger Input
  • 3.3V, 250 Ohm resistors (/5) for 50 Ohm output
    • Normal output = 10 mA per pin

Test

  • Manual or Automated test methods

Manual Test Method

  • Supply Vcc 3.3V to 5V and ground
  • Input is pulled up to Vcc
  • Measure output with BNC T
    • Should be 1/2 of Vcc with 50 Ohm terminator
    • Should be Vcc without terminator

Automated Test Software Method

DRIVE50 P1080485-720PX.jpg

Setup

Procedure

  • Connect 3 pin power cable to card
  • Connect BNC T to output of card
  • Connect BNC female from tester to BNC T male
  • Install 50 terminator to other side of BNC T
  • Connect USB C cable
  • Display will show
PulseGen/DRIVE50 V1.1
50 Ohm card
Set/Got Low
Term High = OK
  • All 3 LEDs are on

Application Example

GPS Frequency Standard

GPS Freq Std P18490-720px.jpg

  • GPS Frequency Standard
  • Card takes in PPS signal out of GPS module and drives 50 Ohm, 10 MHz Frequency Standard output on coax via BNC connector

Mechanicals

DRIVE50 MECHS REV1.PNG

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=DRIVE50&oldid=18974"