Difference between revisions of "ODAS-PSOC5"

From Land Boards Wiki
Jump to navigation Jump to search
 
(83 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/programmable-system-on-a-chip-odas-psoc5/]]
 
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/programmable-system-on-a-chip-odas-psoc5/]]
  
−
 
+
[[file:ODAS-PSOC5_FRONT_3D.png]]
−
[[file:ODAS-PSOC5-P682-X4-720px.jpg]]
 
  
 
<video type="youtube">DijfV5AAAg4</video>
 
<video type="youtube">DijfV5AAAg4</video>
Line 8: Line 7:
 
== Features ==
 
== Features ==
  
−
* PSOC part CY8C5267AXI-LP051
+
* See here for [[ODAS-PSOC5 Rev X1-X4]]
 +
* PSOC5 Programmable System on a Chip
 +
** Part number: [https://www.infineon.com/cms/en/product/microcontroller/32-bit-psoc-arm-cortex-microcontroller/32-bit-psoc-5-lp-arm-cortex-m3/cy8c52lpxxx/cy8c5267axi-lp051/ CY8C5267AXI-LP051]
 
** Core: ARM Cortex M3
 
** Core: ARM Cortex M3
 
** Data Bus Width: 32 bit
 
** Data Bus Width: 32 bit
 
** Maximum Clock Frequency: 67 MHz
 
** Maximum Clock Frequency: 67 MHz
−
** Program Memory Size: 128 kB
+
** Program Memory Type: Flash, 128 kB
−
** Data RAM Size: 32 kB
+
** Data RAM: SRAM, 32 kB
−
** ADC Resolution: 12 bit
+
** ADC
−
** Data RAM Type: SRAM
+
*** Resolution: 12 bit SAR
−
** Interface Type: I2C, USB
+
*** Number of ADC Channels: 1
−
** Number of ADC Channels: 1
+
** 8-bit DAC
 +
** Number of Timers/Counters: 4 Timers
 
** Number of I/Os: 72 I/O
 
** Number of I/Os: 72 I/O
−
** Number of Timers/Counters: 4 Timers
+
*** Interface Types: I2C, USB, SPI
−
** Program Memory Type: Flash
+
** Programmable Analog and Digital sections
 
* 16 MHz External Crystal
 
* 16 MHz External Crystal
 
* Connectors
 
* Connectors
 
** USB Connector (USB-B Mini)
 
** USB Connector (USB-B Mini)
 
** I/O Connector (30 I/O lines which can be analog or digital connections)
 
** I/O Connector (30 I/O lines which can be analog or digital connections)
 +
*** Two voltage zones with 3.3V and 5V selection jumpers
 
** I2C Connector (4-pin header)
 
** I2C Connector (4-pin header)
 
** SPI Connector (6-pin header)
 
** SPI Connector (6-pin header)
−
* Configuration EEPROM
+
* [[Open_Data_Acquisition_System#Personality_EEPROM|ODAS Personality EEPROM]]
−
* 9V power input
+
** [https://www.mouser.com/ProductDetail/579-24LC024-P 24LC024]
−
** Fuses on 3.3V and 5V power
+
** pid = 8
−
*95x45mm Form Factor
+
** Write protect jumper
 +
* On Board LED (5.4)
 +
* Power input on USB B connector
 +
** On-board 3.3V regulator
 +
** Polysilicon fuse on 3.3V power
 +
* 95x55mm ODAS Form Factor
 
* Compatible with Land Boards [[Open Data Acquisition System]] (ODAS) Cards
 
* Compatible with Land Boards [[Open Data Acquisition System]] (ODAS) Cards
 
* (4) #6 screw holes for solid mounting
 
* (4) #6 screw holes for solid mounting
 +
 +
=== CY8C5267AXI-LP051 Features ===
 +
 +
[[file:PSoC5LP_Devices_CY8C5267AXI-LP051.png]]
  
 
=== PSoC Architecture ===
 
=== PSoC Architecture ===
  
−
[[file:PSoC_ArchitecturePic.PNG]]
+
[[file:PSOC5_BlockDiagram.PNG]]
  
 
== Headers ==
 
== Headers ==
  
−
=== H1 - PSOC Programming Header===
+
[[file:ODAS-PSOC5-CAD-REV-5.PNG]]
  
−
# SWDIO
+
=== H1 - I/O Voltage Zone 3 (VZ3) ===
−
# SWDCLK
 
−
# RESET
 
−
# GND
 
−
 
 
−
=== H2 - EEPROM Write Enable ===
 
−
 
 
−
* Install to enable EEPROM writes
 
  
−
=== H3 - I/O Voltage Zone 3 (VZ3) ===
+
[[FILE:ODAS-PSOC5_Rev5_H1.PNG]]
  
 
* 1-2 = 3.3V
 
* 1-2 = 3.3V
Line 57: Line 62:
 
* Connects to J1 VZ3 pins
 
* Connects to J1 VZ3 pins
  
−
=== H4 - I/O Voltage Zone 0 (VZ0) ===
+
=== H2 - I/O Voltage Zone 0 (VZ0) ===
 +
 
 +
[[FILE:ODAS-PSOC5_Rev5_H2.PNG]]
  
 
* 1-2 = 3.3V
 
* 1-2 = 3.3V
Line 63: Line 70:
 
* Connects to J1 VZ0 pins
 
* Connects to J1 VZ0 pins
  
−
== Connectors ==
+
=== H3 - EEPROM Write Enable ===
 +
 
 +
[[FILE:ODAS-PSOC5_Rev5_H3.PNG]]
 +
 
 +
* Install to enable EEPROM writes
 +
 
 +
=== H4 - I2C Terminator ===
 +
 
 +
[[FILE:ODAS-PSOC5_Rev5_H4.PNG]]
  
−
=== J1 - Power ===
+
* Install headers to enable terminators
 +
* 1-2 SDA 3.3K Terminator
 +
* 3-4 SCL 3.3K Terminator
  
−
* 7-12V in
+
== Connectors ==
−
* Regulator provides 5V to card
 
−
* Fuse protected 5V and 3.3V power distribution
 
  
−
=== J2 - USB Micro B ===
+
[[file:ODAS-PSOC5-CAD-REV-5.PNG]]
  
−
* Power not connected through this connector
+
=== P1 - I/O Connector ===
  
−
=== P1 ===
+
[[file:ODAS-PSOC5_Rev5_P1.PNG]]
  
 
{| class="wikitable"
 
{| class="wikitable"
Line 199: Line 214:
 
|-
 
|-
 
| 39
 
| 39
−
| N/C
+
| GND
 
|  
 
|  
 
| 40
 
| 40
−
| N/C
+
| GND
 
|-
 
|-
 
|}
 
|}
  
 +
=== P2 - USB B ===
  
−
=== P2 - I2C Master (or Slave) ===
+
[[file:ODAS-PSOC5_Rev5_P2.PNG]]
  
−
# GND
+
* Power is connected through this connector
−
# 3.3V
+
* USB-Serial connection
−
# SDA
+
 
−
# SCL
+
=== P3 - PSOC SWD Programming Header===
  
−
=== P3 - I2C Terminator ===
+
[[FILE:ODAS-PSOC5_Rev5_P3.PNG]]
  
−
* Install headers to enable terminators
+
# SWDIO
−
* 1-2 SDA 3.3K Terminator
+
# SWDCLK
−
* 3-4 SCL 3.3K Terminator
+
# RESET
 +
# GND
  
 
=== P4 - SPI ===
 
=== P4 - SPI ===
 +
 +
[[FILE:ODAS-PSOC5_Rev5_P4.PNG]]
  
 
# SPI_MOSI
 
# SPI_MOSI
Line 228: Line 247:
 
# +3.3V
 
# +3.3V
 
# GND
 
# GND
 +
 +
=== P5 - I2C Master (or Slave) ===
 +
 +
[[FILE:ODAS-PSOC5_Rev5_P5.PNG]]
 +
 +
# GND
 +
# 3.3V
 +
# SDA
 +
# SCL
  
 
== Programming ==
 
== Programming ==
  
−
* Programming cable
+
[[file:ODAS-PSOC5_P1001_720px.jpg]]
−
* [https://www.infineon.com/cms/en/product/evaluation-boards/cy8ckit-059/ KitProg is a part of CY8CKIT-059]]
+
 
−
** CY8C5868LTI-LP039
+
* Programmed using KitProg
−
** [https://www.infineon.com/dgdl/Infineon-CY8CKIT-059_PSoC_5LP_Prototyping_Kit_Guide-UserManual-v01_00-EN.pdf CY8CKIT-059 Guide]  
+
** KitProg is a part of [https://www.infineon.com/cms/en/product/evaluation-boards/cy8ckit-059/ CY8CKIT-059]
 +
** Has a CY8C5868LTI-LP039 used as the programmer
 +
** Fitted with 1x4 right angle header
 +
** VTARG not connected
 +
* Cables
 +
** 4 pin 1:1 Dupont Programming cable
 +
*** Plugs into SWD (H1) connector on UUT
 +
*** Other end plugs into KitProg J7
 +
** USB A Male to female cable
 +
* [https://www.infineon.com/dgdl/Infineon-CY8CKIT-059_PSoC_5LP_Prototyping_Kit_Guide-UserManual-v01_00-EN.pdf CY8CKIT-059 Guide]  
 
* [https://www.infineon.com/dgdl/Infineon-KitProg_User_Guide-UserManual-v01_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0eee99837dd9 KitProg User Manual]
 
* [https://www.infineon.com/dgdl/Infineon-KitProg_User_Guide-UserManual-v01_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0eee99837dd9 KitProg User Manual]
  
−
[[file:LitProgPlusCable_6159.jpg]]
+
* Program using [https://www.infineon.com/cms/en/design-support/tools/sdk/psoc-software/psoc-creator/ PSOC Creator]
 +
* Select Debug, Program
  
−
* Program using [https://www.infineon.com/cms/en/design-support/tools/sdk/psoc-software/psoc-creator/ PSOC Creator]
+
[[file:PSoC_Prog.PNG]]
 +
 
 +
* Select Device/connect
 +
 
 +
[[file:Sel_PSoC_Target.PNG]]
  
−
== CAD - Rev X4 ==
+
== Factory Acceptance Test (FAT) ==
  
−
[[file:ODAS-PSOC5-CAD-X4-BW.PNG]]
+
[[FILE:ODAS-PSOC5_P108_720PX.jpg]]
  
−
== Test Setup ==
+
<video type="youtube">yB6WmSDGwog</video>
  
−
* [[Arduino Based Test Station]]
+
* Unit Under Test (UUT)
−
** [[LED-32]]
+
** H3 and H4 set to 5V
−
* (2) [[LED-TEST-2]] cards
+
** P3 SDA, SCL termination jumpers installed
−
* [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects/ODAS-PSOC5-LEDS-01.cydsn LED-01 code]
+
** H2 EEWR jumper installed
−
** Bounces a bit across the LEDs
+
** 9V into the DC power jack
 +
* Uses [[LED-32]] card from [[Arduino Based Test Station]]
 +
* Cable set from UUT to [[LED-32]]
 +
* Running [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects/ODAS-PSOC5-LEDS-01.cydsn ODAS-PSOC5-LED-01 Build]
 +
* Lights are lit in the following order
 +
** D0 through D14, LED on card, then D30 through D17
 +
** D16 = power (always on)
 +
** D15, D31 are not used
  
−
[[file:ODAS-PSOC5_P1179_720px.jpg]]
+
== Mechanicals ==
  
−
[[file:LED-TEST-2_TEST-P676-720px.jpg]]
+
[[file:ODAS-PSOC5-MECHS-REV-5.PNG]]
  
 
== Software ==
 
== Software ==
  
 
* [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects GitHub Repository]
 
* [https://github.com/land-boards/ODAS/tree/master/ODAS-PSOC5/Projects GitHub Repository]
 +
 +
== References ==
 +
 +
* [https://www.infineon.com/dgdl/Infineon-AN77759_Getting_Started_with_PSoC_5LP-ApplicationNotes-v08_00-EN.pdf?fileId=8ac78c8c7cdc391c017d071b8fb71dc6&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN77759 Getting Started with PSoC 5LP]
 +
* [https://www.infineon.com/dgdl/Infineon-AN61290_PSoC_3_and_PSoC_5LP_Hardware_Design_Considerations-ApplicationNotes-v17_00-EN.pdf?fileId=8ac78c8c7cdc391c017d07254f524a25&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN61290 PSoC 5LP Hardware Design Considerations]
 +
* [https://www.infineon.com/dgdl/Infineon-AN58304_PSoC_3_and_PSoC_5LP_Pin_Selection_for_Analog_Designs-ApplicationNotes-v09_00-EN.pdf?fileId=8ac78c8c7cdc391c017d072e43f252d4&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN58304 PSoC 5LP – Pin Selection for Analog Designs]
 +
* [https://www.infineon.com/dgdl/Infineon-AN81623_PSoC_3_PSoC_4_and_PSoC_5LP_Digital_Design_Best_Practices-ApplicationNotes-v07_00-EN.pdf?fileId=8ac78c8c7cdc391c017d0726b5b94b78&utm_source=cypress&utm_medium=referral&utm_campaign=202110_globe_en_all_integration-application_note AN81623 PSoC 5LP Digital Design Best Practices]
 +
* [https://www.infineon.com/dgdl/Infineon-AN69133_PSoC_3_PSoC_5LP_Easy_Waveform_Generation_with_the_WaveDAC8_Component-ApplicationNotes-v07_00-EN.pdf?fileId=8ac78c8c7cdc391c017d0730b6d05487 AN69133 PSoC 5LP Easy Waveform Generation with the WaveDAC8 Component]
 +
* [https://www.infineon.com/dgdl/Infineon-CE58035-Code%20Example-v01_00-EN.zip?fileId=8ac78c8c7cdc391c017d0d71d4284c27 I2C EEPROM example]
 +
 +
== Revisions ==
 +
 +
=== Rev 5 ===
 +
 +
* Change to USB B connector
 +
** Power card from 5V through USB B connector
 +
* Remove 5V regulator
 +
* Re-sequence reference designators top to bottom
 +
 +
== Assembly Sheet ==
 +
 +
* [[ODAS-PSOC5 Rev 5 Assembly Sheet]]

Latest revision as of 13:48, 5 September 2022

Tindie-mediums.png

ODAS-PSOC5 FRONT 3D.png

Features

  • See here for ODAS-PSOC5 Rev X1-X4
  • PSOC5 Programmable System on a Chip
    • Part number: CY8C5267AXI-LP051
    • Core: ARM Cortex M3
    • Data Bus Width: 32 bit
    • Maximum Clock Frequency: 67 MHz
    • Program Memory Type: Flash, 128 kB
    • Data RAM: SRAM, 32 kB
    • ADC
      • Resolution: 12 bit SAR
      • Number of ADC Channels: 1
    • 8-bit DAC
    • Number of Timers/Counters: 4 Timers
    • Number of I/Os: 72 I/O
      • Interface Types: I2C, USB, SPI
    • Programmable Analog and Digital sections
  • 16 MHz External Crystal
  • Connectors
    • USB Connector (USB-B Mini)
    • I/O Connector (30 I/O lines which can be analog or digital connections)
      • Two voltage zones with 3.3V and 5V selection jumpers
    • I2C Connector (4-pin header)
    • SPI Connector (6-pin header)
  • ODAS Personality EEPROM
    • 24LC024
    • pid = 8
    • Write protect jumper
  • On Board LED (5.4)
  • Power input on USB B connector
    • On-board 3.3V regulator
    • Polysilicon fuse on 3.3V power
  • 95x55mm ODAS Form Factor
  • Compatible with Land Boards Open Data Acquisition System (ODAS) Cards
  • (4) #6 screw holes for solid mounting

CY8C5267AXI-LP051 Features

PSoC5LP Devices CY8C5267AXI-LP051.png

PSoC Architecture

PSOC5 BlockDiagram.PNG

Headers

ODAS-PSOC5-CAD-REV-5.PNG

H1 - I/O Voltage Zone 3 (VZ3)

ODAS-PSOC5 Rev5 H1.PNG

  • 1-2 = 3.3V
  • 2-3 = 5V
  • Connects to J1 VZ3 pins

H2 - I/O Voltage Zone 0 (VZ0)

ODAS-PSOC5 Rev5 H2.PNG

  • 1-2 = 3.3V
  • 2-3 = 5V
  • Connects to J1 VZ0 pins

H3 - EEPROM Write Enable

ODAS-PSOC5 Rev5 H3.PNG

  • Install to enable EEPROM writes

H4 - I2C Terminator

ODAS-PSOC5 Rev5 H4.PNG

  • Install headers to enable terminators
  • 1-2 SDA 3.3K Terminator
  • 3-4 SCL 3.3K Terminator

Connectors

ODAS-PSOC5-CAD-REV-5.PNG

P1 - I/O Connector

ODAS-PSOC5 Rev5 P1.PNG

Pin Descr Pin Descr
1 GND 2 GND
3 VCC (Zone 0) 4 VCC (Zone 0)
5 Pin.85 6 Pin.84
7 Pin.83 8 Pin.82
9 Pin.81 10 Pin.80
11 Pin.79 12 Pin.78
13 Pin.77 14 Pin.76
15 Pin.74 16 Pin.73
17 Pin.72 18 Pin.71
19 Pin.70 20 Pin.69
21 Pin.68 22 Pin.67
23 Pin.56 24 Pin.55
25 Pin.54 26 Pin.53
27 Pin.52 28 Pin.51
29 Pin.49 30 Pin.48
31 Pin.47 32 Pin.46
33 Pin.45 34 Pin.44
35 VCC (Zone 3) 36 VCC (Zone 3)
37 GND 38 GND
39 GND 40 GND

P2 - USB B

ODAS-PSOC5 Rev5 P2.PNG

  • Power is connected through this connector
  • USB-Serial connection

P3 - PSOC SWD Programming Header

ODAS-PSOC5 Rev5 P3.PNG

  1. SWDIO
  2. SWDCLK
  3. RESET
  4. GND

P4 - SPI

ODAS-PSOC5 Rev5 P4.PNG

  1. SPI_MOSI
  2. SPI_MISO
  3. SPI_CK
  4. SPI_CE0
  5. +3.3V
  6. GND

P5 - I2C Master (or Slave)

ODAS-PSOC5 Rev5 P5.PNG

  1. GND
  2. 3.3V
  3. SDA
  4. SCL

Programming

ODAS-PSOC5 P1001 720px.jpg

  • Programmed using KitProg
    • KitProg is a part of CY8CKIT-059
    • Has a CY8C5868LTI-LP039 used as the programmer
    • Fitted with 1x4 right angle header
    • VTARG not connected
  • Cables
    • 4 pin 1:1 Dupont Programming cable
      • Plugs into SWD (H1) connector on UUT
      • Other end plugs into KitProg J7
    • USB A Male to female cable
  • CY8CKIT-059 Guide
  • KitProg User Manual

PSoC Prog.PNG

  • Select Device/connect

Sel PSoC Target.PNG

Factory Acceptance Test (FAT)

ODAS-PSOC5 P108 720PX.jpg

  • Unit Under Test (UUT)
    • H3 and H4 set to 5V
    • P3 SDA, SCL termination jumpers installed
    • H2 EEWR jumper installed
    • 9V into the DC power jack
  • Uses LED-32 card from Arduino Based Test Station
  • Cable set from UUT to LED-32
  • Running ODAS-PSOC5-LED-01 Build
  • Lights are lit in the following order
    • D0 through D14, LED on card, then D30 through D17
    • D16 = power (always on)
    • D15, D31 are not used

Mechanicals

ODAS-PSOC5-MECHS-REV-5.PNG

Software

References

Revisions

Rev 5

  • Change to USB B connector
    • Power card from 5V through USB B connector
  • Remove 5V regulator
  • Re-sequence reference designators top to bottom

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=ODAS-PSOC5&oldid=19577"