Difference between revisions of "ER-ADSR-555-01"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 71: | Line 71: | ||
* Made new build | * Made new build | ||
* Cuts before build | * Cuts before build | ||
| − | * Cuts to RV1 | + | * Cuts to RV1 (pins 2-3) |
| − | [[FILE: | + | [[FILE:RV1_FIX.PNG]] |
| + | * Cuts to RV2 (pins 2-3) | ||
| + | |||
| + | [[FILE:RV2_FIX.PNG]] | ||
* Cut to RV4 | * Cut to RV4 | ||
Revision as of 17:23, 5 November 2022
Contents
Eurorack ADSR Module
Features
- Attack-DeCay-Sustain-Release Eurorack ADSR Module
- Takes in Gate signal, generates CV to VCA
- Attack, decay, and release pots control speed
- Attack, decay, and release times can range from 200ms to 16s
- Sustain pot sets the sustain voltage level
- LED dims to level
- 3U tall, 6 HP wide
- 555 Based design
- Benjie Jiao MiniADSR
- Original was based on Barry Klein design
- As built by schmitzbits design - "The Fastest Envelope in the West"
- Benji's build has a three card stack-up and is 4 HP wide
- This card is wider but uses 2 cards
Rev 1 Checkout
- Ordered wrong (earlier) version of the board
- Re-create ordered board in Rev 1 folder
- Annotated schematic
- Drive with Erica Synths EDU Sequencer
- GATE Out output
- At slowest speed, ~2Hz
- My schematic symbols are Schottky but installed 1N4148 like schmitzbits schemati
- Using 1 M linear pots instead of 2.2M log pots
- A, D, R pots should have been log pots
- Controls are are "touchy"
- Sustain pot is linear as it should be and "works" but is backwards
- All of the pots are backwards
- A, D, S pots should be CCW for no delay
- ADR series resistors are 220 Ohms but should be 100 Ohms per schmitzbits note
- C3 is 4.7 uF
- Log pot curves
- Does not have 1M that is dashed line on schmitzbits schemati
- ADSR controls
- A pot full CW
- D pot full CW
- S Pot mid
- R pot full CW
- Back off Attack just a tiny bit from CCW
- Rounds over the attack like it should but it is very "touchy"
Benjie Jiao - DIY Modular Video
Issues
Rev 1 Issues
- Silkscreen has "DELAY" should be "DECAY"
- A, D, S, R pots are all backwards
- A, D, R pots should be A1M
- Made new build
- Cuts before build
- Cuts to RV1 (pins 2-3)
- Cuts to RV2 (pins 2-3)
- Cut to RV4
TBD FIX
- Cut rear side etch 555 U2, at U7-7
- Add wire R10 left side to Sustain pot, RV3 right side
- Add wire U2-7 to to Sustain pot, RV3 left side
- 220 Ohms on A, D, R pots s/b 100 Ohms
- Change R7 to 100 Ohms (A pot)
- Change R8 to 100 Ohms (D pot)
- Change R10 to 100 Ohms (R pot)
- Reverse A. D. R pots
- Cut RV1-2 to RV1-3
- Add wire RV1-2 to RV1-1
- Cut RV2-2 to RV2-3
- Add wire RV2-2 to RV2-1
- Cut etch RV4-2 to RV4-3
- Cut back size etch R10 to RV4-2
- Add wire R10 to RV4-3
- Add wire RV4-1 to RV4-2
