Difference between revisions of "NanoVNA"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 24: | Line 24: | ||
* My unit did not come with a battery | * My unit did not come with a battery | ||
| − | * Added an ST connector | + | * Added an SMT mount ST connector to the board |
| + | * Added an 850 mAh LiPo battery | ||
* The pinout on the card was backwards from the pinout of the connector at the end of the battery wires | * The pinout on the card was backwards from the pinout of the connector at the end of the battery wires | ||
| − | * Removed the pins from the battery wire connector and flipped the pins | + | ** Removed the pins from the battery wire connector and flipped the pins |
| − | * Charging | + | * Charging works |
* Battery is a bit too thick to screw the back on completely | * Battery is a bit too thick to screw the back on completely | ||
| − | * | + | * Switched to longer standoffs |
* Someone else's page (they added an inline connector and wired to the card) | * Someone else's page (they added an inline connector and wired to the card) | ||
** [https://www.epanorama.net/blog/2019/09/29/battery-for-nanovna/ Adding a battery] | ** [https://www.epanorama.net/blog/2019/09/29/battery-for-nanovna/ Adding a battery] | ||
Revision as of 18:24, 17 September 2020
Contents
NanoVNA - Network Analyzer
Specifications
- Number of Calibration Points: 101 (Fixed)
- Number of Scanning Points: 101 (Fixed)
- Display Tracking: 4, Marking: 4, Save Setting : 5
- PCB: 54mm x 85.5mm x 11mm (without the size of connectors, switches)
- Measurement Frequency: 50KHz ~ 300MHz (50KHz -900MHz, enable extended firmware)
- RF Output: -13dbm (maximum -9dbm)
- Frequency Accuracy: 0.5ppm
- Measurement Range: 70dB (50kHz-300MHz), 50dB (300M-600MHz), 40dB (600M-900MHz) enable extended firmware)
- Port SWR: 1.1
- Display: 2.8 inch TFT (320 x240)
- USB Interface: USB Type-C; Communications Mode: CDC (Serial)
- Power Supply: USB 5V 120mA, built-in 400mAh electricity, maximum charging current 0.8A
- nanovna users nanovna-users@groups.io
- Amazon links
Adding a battery
- My unit did not come with a battery
- Added an SMT mount ST connector to the board
- Added an 850 mAh LiPo battery
- The pinout on the card was backwards from the pinout of the connector at the end of the battery wires
- Removed the pins from the battery wire connector and flipped the pins
- Charging works
- Battery is a bit too thick to screw the back on completely
- Switched to longer standoffs
- Someone else's page (they added an inline connector and wired to the card)
Software
YouTube Videos
<video type="youtube">bEPUePy_buM/video>
- NanoVNA a $50-$70 Amateur Radio Antenna Analyzer? - Ham Radio Crash Course
- NanoVNA Initial Observations - W0QE
- The NanoVNA, a beginners guide to the Vector Network Analyzer - joe smith
- The NanoVNA, Viewer Questions and Answers - joe smith
- Using the NanoVNA to Create SPICE Models for Simulation - joe smith
- NanoVNA Vector Network analyzer 900MHz VNA for $50 - IMSAI Guy
- NANOVNA LP Low Pass Filter - IMSAI Guy
- NANOVNA Garage sale Antenna Tuner with roller inductor - IMSAI Guy
- Basics of the Smith Chart - Intro, impedance, VSWR, transmission lines, matching - W2AEW
- NanoVNA To Test The Loss & Length Of Coax Cables - Jim W6LG YouTube Elmer for Ham Radio Basics
