Difference between revisions of "DIGIO-128 Rev X4 Assembly Sheet"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (12 intermediate revisions by the same user not shown) | |||
| Line 17: | Line 17: | ||
| | | | ||
| 1 | | 1 | ||
| − | | | + | | Header, 2X03 |
| J4 | | J4 | ||
|- | |- | ||
| − | | 1 | + | | 1 |
| − | | 0 | + | | 0 (wire jumper) |
| − | | R7 | + | | R7 |
| | | | ||
| 2 | | 2 | ||
| − | | | + | | Header, 1x4 |
| − | | J2,J3 | + | | J2, J3 |
|- | |- | ||
| − | | | + | | 3 |
| − | |||
| 10K (1/4W) | | 10K (1/4W) | ||
| − | | R1,R2 | + | | R1, R2, R6 |
| − | |||
| | | | ||
| 1 | | 1 | ||
| − | | | + | | Header, 1x5 |
| J1 | | J1 | ||
|- | |- | ||
| Line 43: | Line 41: | ||
| | | | ||
| 8 | | 8 | ||
| − | | | + | | Header, 2x10 |
| − | | P1 | + | | P1-P4, P6-P9 |
|- | |- | ||
| 2 | | 2 | ||
| Line 51: | Line 49: | ||
| | | | ||
| 2 | | 2 | ||
| − | | | + | | Header, 2X2 |
| − | | P10 | + | | P5, P10 |
|- | |- | ||
| 1 | | 1 | ||
| Line 58: | Line 56: | ||
| U9 | | U9 | ||
| | | | ||
| − | | | + | | 3 |
| − | | | + | | Shunts |
| − | | | + | | J4 |
|- | |- | ||
| 8 | | 8 | ||
| MCP23017P | | MCP23017P | ||
| − | | U1 | + | | U1-U8 |
| | | | ||
| | | | ||
| Line 74: | Line 72: | ||
== R6/R7 Option == | == R6/R7 Option == | ||
| + | * This option is not factory configuration | ||
* R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27 | * R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27 | ||
| − | * | + | ** Clip out R7 jumper to shift address up (not typical use) |
| − | * R7 | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 13:18, 12 February 2021
Parts List
| Qty | Value | RefDes | Qty | Value | RefDes | |
|---|---|---|---|---|---|---|
| 8 | 0.1uF Cap, 0.2" pitch | C1-C8 | 1 | Header, 2X03 | J4 | |
| 1 | 0 (wire jumper) | R7 | 2 | Header, 1x4 | J2, J3 | |
| 3 | 10K (1/4W) | R1, R2, R6 | 1 | Header, 1x5 | J1 | |
| 1 | 1K (1/4W) | R5 | 8 | Header, 2x10 | P1-P4, P6-P9 | |
| 2 | 2.2K (1/4W) | R3,R4 | 2 | Header, 2X2 | P5, P10 | |
| 1 | 24LC024-I/P | U9 | 3 | Shunts | J4 | |
| 8 | MCP23017P | U1-U8 |
R6/R7 Option
- This option is not factory configuration
- R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27
- Clip out R7 jumper to shift address up (not typical use)
