Difference between revisions of "LED-32"

From Land Boards Wiki
Jump to navigation Jump to search
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/32-led-card-pwb-only-or-assembled/]]
 +
 
[[File:LED-32-P426-720px.jpg]]
 
[[File:LED-32-P426-720px.jpg]]
  
Line 18: Line 20:
 
* For 5V operation and not too bright LED (comfortable value for front panels) we use 560 ohms.
 
* For 5V operation and not too bright LED (comfortable value for front panels) we use 560 ohms.
 
* With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.
 
* With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.
 +
 +
== Test Procedure ==
 +
 +
=== Setup ===
 +
 +
* [[PiPicoMite02 Based Test Station]]
 +
** [[PiPicoMite02]] Processor card
 +
* LED-32 - Unit Under Test (UUT)
 +
* [[DB37RIBBON]] plugged into UUT
 +
* (2) of 2x10 cables to connect between [[DB37RIBBON]] and UUT
 +
** DB37-1 marked on cable end goes near P1 marked on [[DB37RIBBON]]
 +
* LED32-1 marked on cable end goes near HDR1 marked on UUT
 +
 +
=== Card Test Procedure ===
 +
 +
* Power up Test Station/UUT
 +
* Type
 +
 +
<pre>
 +
chdir "/lbcards/GPIO32"
 +
load " GPIO32-01.bas"
 +
run
 +
 +
</pre>
 +
 +
* Should see the LEDs go around the UUT card
 +
* Hit any key to stop (after finishing rotation)
 +
 +
== Pinout ==
 +
 +
{| class="wikitable"
 +
! HDR1 pin
 +
! LED
 +
!
 +
! HDR1 pin
 +
! LED
 +
|-
 +
| 1
 +
| GND
 +
|
 +
| 2
 +
| GND
 +
|-
 +
| 3
 +
| GND
 +
|
 +
| 4
 +
| GND
 +
|-
 +
| 5
 +
| D0
 +
|
 +
| 6
 +
| D16
 +
|-
 +
| 7
 +
| D1
 +
|
 +
| 8
 +
| D17
 +
|-
 +
| 9
 +
| D2
 +
|
 +
| 10
 +
| D18
 +
|-
 +
| 11
 +
| D3
 +
|
 +
| 12
 +
| D19
 +
|-
 +
| 13
 +
| D4
 +
|
 +
| 14
 +
| D20
 +
|-
 +
| 15
 +
| D5
 +
|
 +
| 16
 +
| D21
 +
|-
 +
| 17
 +
| D6
 +
|
 +
| 18
 +
| D22
 +
|-
 +
| 19
 +
| D7
 +
|
 +
| 20
 +
| D23
 +
|-
 +
| 21
 +
| D8
 +
|
 +
| 22
 +
| D24
 +
|-
 +
| 23
 +
| D9
 +
|
 +
| 24
 +
| D25
 +
|-
 +
| 25
 +
| D10
 +
|
 +
| 26
 +
| D26
 +
|-
 +
| 27
 +
| D11
 +
|
 +
| 28
 +
| D27
 +
|-
 +
| 29
 +
| D12
 +
|
 +
| 30
 +
| D28
 +
|-
 +
| 31
 +
| D13
 +
|
 +
| 32
 +
| D29
 +
|-
 +
| 33
 +
| D14
 +
|
 +
| 34
 +
| D30
 +
|-
 +
| 35
 +
| D15
 +
|
 +
| 36
 +
| D31
 +
|-
 +
| 37
 +
| GND
 +
|
 +
| 38
 +
| GND
 +
|-
 +
| 39
 +
| GND
 +
|
 +
| 40
 +
| GND
 +
|-
 +
|}
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
  
 
* [[LED-32_Assembly_Sheet]]
 
* [[LED-32_Assembly_Sheet]]

Latest revision as of 18:58, 12 March 2023

Tindie-mediums.png

LED-32-P426-720px.jpg

Features

  • 32 LEDs
  • 95mm wide (ODAS width) - 55mm depth matches other ODAS cards ODAS-PSOC5 (Rev X3 or higher), DIGIO32-I2C, etc
  • 6-32 mounting holes
  • 0.1" pitch connector, 2x20 pins, Connector could be mounted to the front or rear of the card
  • (8) Ground pins (common ground)
  • 3mm LEDs

Series resistor - let us know what value you want

  • Series Resistor Values
  • Pick a series resistor value assuming the LED forward voltage is about 2V.
  • Operating with 3.3V will require a smaller resistance than operating at 5V for the same current.
  • Standard series resistor values we carry are: 120, 150, 200, 220, 240, 270, 330, 470, 560, and 1K.
  • For 5V operation and not too bright LED (comfortable value for front panels) we use 560 ohms.
  • With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.

Test Procedure

Setup

Card Test Procedure

  • Power up Test Station/UUT
  • Type
chdir "/lbcards/GPIO32"
load " GPIO32-01.bas"
run
  • Should see the LEDs go around the UUT card
  • Hit any key to stop (after finishing rotation)

Pinout

HDR1 pin LED HDR1 pin LED
1 GND 2 GND
3 GND 4 GND
5 D0 6 D16
7 D1 8 D17
9 D2 10 D18
11 D3 12 D19
13 D4 14 D20
15 D5 16 D21
17 D6 18 D22
19 D7 20 D23
21 D8 22 D24
23 D9 24 D25
25 D10 26 D26
27 D11 28 D27
29 D12 30 D28
31 D13 32 D29
33 D14 34 D30
35 D15 36 D31
37 GND 38 GND
39 GND 40 GND

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=LED-32&oldid=24725"