Difference between revisions of "NANO-BKOUT"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/nano-breakout-card/]] | [[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/nano-breakout-card/]] | ||
| + | |||
| + | [[File:NANO-BKOUT-P1010078-800px.jpg]] | ||
== Arduino Nano Breakout card == | == Arduino Nano Breakout card == | ||
| − | This card breaks out | + | This card breaks out an Arduino Nano (not supplied with NANO-BKOUT card) into GVS (Ground-Voltage-Signal) headers for easy connection to external sensors. |
| − | |||
| − | |||
== Features == | == Features == | ||
| − | * Breakout card for the Arduino Nano | + | * Breakout card for the [[Arduino Nano]] |
* NANO (not supplied) is: | * NANO (not supplied) is: | ||
** Inexpensive ($6-$7 US, $2.50 China), multiple sourced part | ** Inexpensive ($6-$7 US, $2.50 China), multiple sourced part | ||
| Line 26: | Line 26: | ||
* I2C header | * I2C header | ||
* Aref voltage selection header | * Aref voltage selection header | ||
| − | * Direct connection to MyMenu card | + | * Direct connection to [[MyMenu]] card |
** I2C Interface | ** I2C Interface | ||
** D6 connection for interrupt line | ** D6 connection for interrupt line | ||
| Line 34: | Line 34: | ||
* Rounded corners to allow card to be installed into enclosure corners | * Rounded corners to allow card to be installed into enclosure corners | ||
| − | == Connectors - Rev X1 == | + | === NANO Pinout === |
| + | |||
| + | [[file:arduino-nano-pinout-877PX.png]] | ||
| + | |||
| + | == Connectors == | ||
| + | |||
| + | [[FILE:NANO-BKOUT_PINOUT.PNG]] | ||
| + | |||
| + | === Rev X1 I2C Connector === | ||
[[File:NANO-BKOUT-Conns.png]] | [[File:NANO-BKOUT-Conns.png]] | ||
| Line 67: | Line 75: | ||
* [[Arduino Based Test Station]] | * [[Arduino Based Test Station]] | ||
* [https://github.com/land-boards/lb-Arduino-Code/tree/master/LBCards/ODAS/ODASTESTER ODAS Tester Github Repo] | * [https://github.com/land-boards/lb-Arduino-Code/tree/master/LBCards/ODAS/ODASTESTER ODAS Tester Github Repo] | ||
| + | |||
| + | == Board Test == | ||
| + | |||
| + | === Hardware === | ||
| + | |||
| + | * UUT | ||
| + | ** AREF Jumper installed from pin 2 to 5V Legend | ||
| + | * Arduino NANO | ||
| + | * [[POWER-49MM]] card | ||
| + | * 2x [[LED-TEST-2]] cards | ||
| + | * Cable Set | ||
| + | * USB or external DC power | ||
| + | |||
| + | === Cabling === | ||
| + | |||
| + | * The cable wires the LEDs to the UUT pins. | ||
| + | * Pins A6 and A7 are untested since they are analog inputs only. | ||
| + | |||
| + | Test Station Cable Marking and installation locations are: | ||
| + | |||
| + | * L01 - Goes to LED-TEST-2 card #1 LEDS 1-4 | ||
| + | * L05 - Goes to LED-TEST-2 card #1 LEDS 5-8 | ||
| + | * L09 - Goes to LED-TEST-2 card #1 LEDS 9-12 | ||
| + | * L13 - Goes to LED-TEST-2 card #1 LEDS 13-16 | ||
| + | * L17 - Goes to LED-TEST-2 card #2 LEDS 1-4 | ||
| + | * G1 - Goes to POWER-49MM card on "-" pins | ||
| + | * G5 - Goes to POWER-49MM card on "-" pins | ||
| + | |||
| + | UUT Cable Marking and installation locations are: | ||
| + | |||
| + | * D3 - Goes to UUT D3 (and D2) location | ||
| + | * D5 - Goes to UUT D5 (and D4) location | ||
| + | * D5 - Goes to UUT D5 (and D4) location | ||
| + | * I2C - Goes to UUT I2C location | ||
| + | * D8 - Goes to UUT D8 (and D7) location | ||
| + | * D9 - Goes to UUT D9 location | ||
| + | * D10 - Goes to UUT D10 location | ||
| + | * SER - Goes to Serial location | ||
| + | * ISP - Goes to UUT ISP location | ||
| + | * A0 - Goes to UUT A0 (and A1) location | ||
| + | * A2 - Goes to UUT A2 (and A3) location | ||
| + | |||
| + | === Test Software === | ||
| + | |||
| + | == Board Revs == | ||
| + | |||
| + | === Rev X2 === | ||
| + | |||
| + | * Same netlist as X1 | ||
| + | * Moved I2C connector under the Nano to avoid interference with [MyMenu] connection | ||
| + | |||
| + | === Rev X1 === | ||
| + | |||
| + | * Tough to solder in the I2C connector when used with MyMenu card | ||
| + | |||
| + | == Links == | ||
| + | |||
| + | * [https://www.arduino.cc/en/Main/ArduinoBoardNano Arduino Nano Page] | ||
| + | * [https://www.arduino.cc/en/uploads/Main/ArduinoNano30Schematic.pdf Arduino Nano schematic] | ||
== Assembly Sheet == | == Assembly Sheet == | ||
* [[Arduino Nano Breakout Card Assembly Sheet]] | * [[Arduino Nano Breakout Card Assembly Sheet]] | ||
Latest revision as of 12:24, 12 October 2022
Contents
Arduino Nano Breakout card
This card breaks out an Arduino Nano (not supplied with NANO-BKOUT card) into GVS (Ground-Voltage-Signal) headers for easy connection to external sensors.
Features
- Breakout card for the Arduino Nano
- NANO (not supplied) is:
- Inexpensive ($6-$7 US, $2.50 China), multiple sourced part
- 5V, 16 MHz
- Installs onto female header/removable
- DC regulator
- Microprocessor ATMega328 Comparable with Arduino UNO
- Mini USB connector
- Reset switch
- NANO-BKOUT has
- DC Power Jack
- GVS connections for most digital/analog signals
- Ground and power connections for each digital lines simplify power distribution to external functions such as sensors
- Additional analog input signals (over the Arduino UNO)
- ICSP (In-Circuit System Programmer) header
- I2C header
- Aref voltage selection header
- Direct connection to MyMenu card
- I2C Interface
- D6 connection for interrupt line
- Located in mirrored location on both boards to allow the MyMenu to mount to the rear
- 49x49mm form factor
- (4) 4-40 mounting holes for installation into enclosures
- Rounded corners to allow card to be installed into enclosure corners
NANO Pinout
Connectors
Rev X1 I2C Connector
ISP Connector
- D12
- +5V
- D13
- D11
- RST*
- GND
(H18) AREF Select Jumper
- 1-2 = External AREF (via shared power pins)
- 2-3 = Use 5V as AREF = Factory position
NANO-BKOUT Plus MyMenu
- NANO-BKOUT
- MyMenu
Testing
Board Test
Hardware
- UUT
- AREF Jumper installed from pin 2 to 5V Legend
- Arduino NANO
- POWER-49MM card
- 2x LED-TEST-2 cards
- Cable Set
- USB or external DC power
Cabling
- The cable wires the LEDs to the UUT pins.
- Pins A6 and A7 are untested since they are analog inputs only.
Test Station Cable Marking and installation locations are:
- L01 - Goes to LED-TEST-2 card #1 LEDS 1-4
- L05 - Goes to LED-TEST-2 card #1 LEDS 5-8
- L09 - Goes to LED-TEST-2 card #1 LEDS 9-12
- L13 - Goes to LED-TEST-2 card #1 LEDS 13-16
- L17 - Goes to LED-TEST-2 card #2 LEDS 1-4
- G1 - Goes to POWER-49MM card on "-" pins
- G5 - Goes to POWER-49MM card on "-" pins
UUT Cable Marking and installation locations are:
- D3 - Goes to UUT D3 (and D2) location
- D5 - Goes to UUT D5 (and D4) location
- D5 - Goes to UUT D5 (and D4) location
- I2C - Goes to UUT I2C location
- D8 - Goes to UUT D8 (and D7) location
- D9 - Goes to UUT D9 location
- D10 - Goes to UUT D10 location
- SER - Goes to Serial location
- ISP - Goes to UUT ISP location
- A0 - Goes to UUT A0 (and A1) location
- A2 - Goes to UUT A2 (and A3) location
Test Software
Board Revs
Rev X2
- Same netlist as X1
- Moved I2C connector under the Nano to avoid interference with [MyMenu] connection
Rev X1
- Tough to solder in the I2C connector when used with MyMenu card
