Difference between revisions of "ER-PROTO-01"

From Land Boards Wiki
Jump to navigation Jump to search
 
(110 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/28599/]]
 +
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
  
Line 31: Line 33:
  
 
* J1-J4 are front panel connectors
 
* J1-J4 are front panel connectors
 +
 +
=== Inter-card Connectors ===
 +
 +
==== Pots ====
 +
 +
* J5 on the Controls card and J5 on the I/O card
 +
* Pot connections
 +
** POTx-1 is fully CW connects to wiper
 +
** POTx-2 is wiper
 +
** POTX-3 is fully CCW connects to wiper
 +
 +
[[FILE:RV_Conns.PNG]]
 +
 +
* To make pot into voltage control
 +
**  POTx-1 (CW) = +5V
 +
**  POTx-13CCW = GND
 +
** Wire RV1-1 to RV3-1 to RV5-1 on controls card
 +
** Wire RV1-3 to RV3-3 to RV5-3 on controls card
 +
** Wire RV2-1 to RV4-1 to RV6-1 on controls card
 +
** Wire RV2-3 to RV4-3 to RV6-3 on controls card
 +
 +
[[file:ER-PROTO-CTLS-6-01_J5.PNG]]
 +
 +
==== Jacks ====
 +
 +
* J6 on the controls card and J37 on the I/O card
 +
 +
[[file:ER-PROTO-CTLS-6-01_J10.PNG]]
 +
 +
== Daughtercard Connectors ==
 +
 +
=== J5, J37 - POT connectione ===
 +
 +
[[file:ER-PROTO-DB-01_J5.png]]
 +
 +
[[file:ER-PROTO-DB-01_J37.png]]
 +
 +
=== J6 - Eurorack Power ===
 +
 
* J6 on the I/O card
 
* J6 on the I/O card
 
** Eurorack power
 
** Eurorack power
 
** 2x5 IDC
 
** 2x5 IDC
 +
** GATE, CV not connected
  
 
[[file:ER-PROTO-DB-01_J6.png]]
 
[[file:ER-PROTO-DB-01_J6.png]]
  
=== Inter-card Connectors ===
+
=== J10 - Jacks connections on Controls card ===
 +
 
 +
[[file:ER-PROTO-DB-01_J10.png]]
 +
 
 +
=== J38 - Jacks connections ===
 +
 
 +
[[file:ER-PROTO-DB-01_J38.png]]
 +
 
 +
== Examples ==
 +
 
 +
=== Arduino NANO MOZZI ===
 +
 
 +
[[Arduino NANO MOZZI on ER-PROTO-01]]
 +
 
 +
[[file:ER-PROTO-01-NANO-MOZZI_P1080687-720PX.jpg]]
 +
 
 +
[[file:ER-PROTO-01-NANO-MOZZI_P1080693-720PX.jpg]]
 +
 
 +
=== CV4 - 4 Control Voltages ===
 +
 
 +
[[ER-CVPOTS4]]
 +
 
 +
[[file:ER-PROTO-01-CV4_P1090031-F_B_720px.jpg]]
 +
 
 +
=== Noise Generator ===
  
* J5 on the Controls card and J5 on the I/O card
+
[[Noise_Generator_on_ER-PROTO-01|Noise Generator on ER-PROTO-01]]
  
[[file:ER-PROTO-CTLS-6-01_J5.PNG]]
+
[[file:ER-PROTO-01_NOISE_P1080751-720px.jpg]]
  
* J6 on the controls card and J37 on the I/O card
+
[[file:ER-PROTO-01_NOISE_P1080755-720px.jpg]]
  
[[file:ER-PROTO-CTLS-6-01_J10.PNG]]
+
=== Slew Rate Controller ===
  
== Example ==
+
[[Slew Rate Controller on ER-PROTO-01]]
  
* Arduino NANO with quad Opamp example
+
== Assembly Sheet ==
  
[[file:ER-PROTO-DB-01_ARDUINO_NANO_OPAMP-720px.png]]
+
* [[ER-PROTO-01 Assembly Sheet]]

Latest revision as of 17:48, 18 January 2023

Tindie-mediums.png

ER-PROTO-PANEL-01-SET FRONT REAR-3D-720px.png

Features

  • Eurorack Prototyping card set
  • 6 HP wide (30mm) front panel
  • 3U tall
  • Three card set
    • Board interconnect headers duplicated on headers
    • 30mm wide front panel
    • 28mm wide panel and daughtercards
  • 6 POTS
    • Marked as RV1-RV5
    • Series resistors on pot wiper
    • All 3 pot pins brought to top header
  • 4 Jacks
    • Marked as J1-J4
    • Tip/sleeve brought to header near middle/bottom
  • Pots on top, jacks on bottom of card
    • Easier to adjust pots without bumping into pots
    • Pots more often accessed than jacks
  • Large prototyping area
    • 58 nodes with 3 holes per node (29 per "side")
  • +12V, -12V down board edges
  • 5V/GND down center of card
  • Bussed connections horizontally
  • Front Panel with generic labels
    • Cover with White on Black P-Touch labels

Connectors

  • J1-J4 are front panel connectors

Inter-card Connectors

Pots

  • J5 on the Controls card and J5 on the I/O card
  • Pot connections
    • POTx-1 is fully CW connects to wiper
    • POTx-2 is wiper
    • POTX-3 is fully CCW connects to wiper

RV Conns.PNG

  • To make pot into voltage control
    • POTx-1 (CW) = +5V
    • POTx-13CCW = GND
    • Wire RV1-1 to RV3-1 to RV5-1 on controls card
    • Wire RV1-3 to RV3-3 to RV5-3 on controls card
    • Wire RV2-1 to RV4-1 to RV6-1 on controls card
    • Wire RV2-3 to RV4-3 to RV6-3 on controls card

ER-PROTO-CTLS-6-01 J5.PNG

Jacks

  • J6 on the controls card and J37 on the I/O card

ER-PROTO-CTLS-6-01 J10.PNG

Daughtercard Connectors

J5, J37 - POT connectione

ER-PROTO-DB-01 J5.png

ER-PROTO-DB-01 J37.png

J6 - Eurorack Power

  • J6 on the I/O card
    • Eurorack power
    • 2x5 IDC
    • GATE, CV not connected

ER-PROTO-DB-01 J6.png

J10 - Jacks connections on Controls card

ER-PROTO-DB-01 J10.png

J38 - Jacks connections

ER-PROTO-DB-01 J38.png

Examples

Arduino NANO MOZZI

Arduino NANO MOZZI on ER-PROTO-01

ER-PROTO-01-NANO-MOZZI P1080687-720PX.jpg

ER-PROTO-01-NANO-MOZZI P1080693-720PX.jpg

CV4 - 4 Control Voltages

ER-CVPOTS4

ER-PROTO-01-CV4 P1090031-F B 720px.jpg

Noise Generator

Noise Generator on ER-PROTO-01

ER-PROTO-01 NOISE P1080751-720px.jpg

ER-PROTO-01 NOISE P1080755-720px.jpg

Slew Rate Controller

Slew Rate Controller on ER-PROTO-01

Assembly Sheet