Difference between revisions of "ER-PROTO-01"

From Land Boards Wiki
Jump to navigation Jump to search
 
(71 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:tindie-mediums.png|link=https://www.tindie.com/products/28599/]]
 +
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
 
[[FILE:ER-PROTO-PANEL-01-SET_FRONT_REAR-3D-720px.png]]
  
Line 89: Line 91:
 
=== Arduino NANO MOZZI ===
 
=== Arduino NANO MOZZI ===
  
−
==== NANO Pinout ====
+
[[Arduino NANO MOZZI on ER-PROTO-01]]
  
−
[[FILE:arduino-nano-pinout-720px.png]]
+
[[file:ER-PROTO-01-NANO-MOZZI_P1080687-720PX.jpg]]
  
−
==== Controls ====
+
[[file:ER-PROTO-01-NANO-MOZZI_P1080693-720PX.jpg]]
  
−
* 6 Pots
+
=== CV4 - 4 Control Voltages ===
−
** RV1 = Analog 7
 
−
** RV2 - Analog 4
 
−
** RV3 - Analog 6
 
−
** RV4 - Analog 3
 
−
** RV5 - Analog 5
 
−
** RV6 - Analog 2
 
−
* 2 CV Input Jacks
 
−
** J1 = Analog 0
 
−
** J2 = Analog 1
 
−
* 1 Output Jack
 
−
** J4 = MOZZI HI DEF Audio
 
−
 
 
−
==== Audio Out Schematic ====
 
−
 
 
−
[[FILE:ER-MOZZI-AUDIO_OUT_SCHEM.PNG]]
 
−
 
 
−
==== CV In Schematic ====
 
−
 
 
−
* ANA0 in example
 
−
 
 
−
[[FILE:ER-MOZZI-CV_IN_SCHEM.PNG]]
 
−
 
 
−
==== Parts ====
 
−
 
 
−
* 3D view
 
−
 
 
−
[[FILE:ER-MOZZI-PARTS_3D.PNG]]
 
  
−
* Top parts view
+
[[ER-CVPOTS4]]
  
−
[[FILE:ER-MOZZI-PARTS_DETAILS_TOP-3D.PNG]]
+
[[file:ER-PROTO-01-CV4_P1090031-F_B_720px.jpg]]
  
−
* Bottom parts view
+
=== Noise Generator ===
  
−
[[FILE:ER-MOZZI-CV_IN_FILTER.PNG]]
+
[[Noise_Generator_on_ER-PROTO-01|Noise Generator on ER-PROTO-01]]
  
−
* With NANO
+
[[file:ER-PROTO-01_NOISE_P1080751-720px.jpg]]
  
−
[[FILE:ER-MOZZI-NANO_3D.PNG]]
+
[[file:ER-PROTO-01_NOISE_P1080755-720px.jpg]]
  
−
* CAD placement
+
=== Slew Rate Controller ===
  
−
[[FILE:ER-MOZZI-PARTS_CAD.PNG]]
+
[[Slew Rate Controller on ER-PROTO-01]]
  
−
==== Wires ====
+
== Assembly Sheet ==
  
−
<PRE>
+
* [[ER-PROTO-01 Assembly Sheet]]
−
NET: ANA0, A1-19, (C7-1, D1-2, D3-1, R9-2)
 
−
NET: ANA1, A1-20, (C8-1, D2-2, D4-1, R10-2)
 
−
NET: ANA2, A1-21, J37-3
 
−
NET: ANA3, A1-22, J37-6
 
−
NET: ANA4, A1-23, J37-9
 
−
NET: ANA5, A1-24, J37-12
 
−
NET: ANA6, A1-25, J37-15
 
−
NET: ANA7, A1-26, J37-18
 
−
NET: J1-T, J38-1, (R7-1, R9-1)
 
−
NET: J2-T, J38-5, (R10-1, R8-1)
 
−
NET: J4-T, J38-7, (C10-1, R14-2)
 
−
NET: GND1, J37-7
 
−
NET: GND2, J38-6
 
−
NET: GND3, A1-4
 
−
NET: GND4, A1-29
 
−
NET: +5VD, A1-27, J37-11
 
−
NET: L5V, J37-14, J37-8
 
−
NET: LGND, J37-16, J37-4
 
−
</PRE>
 
−
 
 
−
==== Parts List ====
 
−
 
 
−
{| class="wikitable"
 
−
! Find
 
−
! Qty
 
−
! Ref Des
 
−
! Part Number
 
−
|-
 
−
| 1
 
−
| 2
 
−
| R7, R8
 
−
| 100K
 
−
|-
 
−
| 2
 
−
| 2
 
−
| R9, R10
 
−
| 10K
 
−
|-
 
−
| 3
 
−
| 2
 
−
| R11, R14
 
−
| 3.9K
 
−
|-
 
−
| 4
 
−
| 2
 
−
| R12, R13
 
−
| 1M
 
−
|-
 
−
| 5
 
−
| 4
 
−
| D1-D4
 
−
| BAT41
 
−
|-
 
−
| 6
 
−
| 8
 
−
| C1-C8
 
−
| 0.1uF
 
−
|-
 
−
| 7
 
−
| 1
 
−
| C9
 
−
| 4.7nF
 
−
|-
 
−
| 8
 
−
| 1
 
−
| C10
 
−
| 10nF
 
−
|-
 
−
| 9
 
−
| 1
 
−
| J5
 
−
| HEADER, 2X10
 
−
|-
 
−
| 10
 
−
| 1
 
−
| J6
 
−
| [https://store.synthrotek.com/16-Pin_Keyed_Shrouded_Eurorack_Power_Header HEADER, 2X8]
 
−
|-
 
−
| 11
 
−
| 1
 
−
| J10
 
−
| HEADER, 1x8
 
−
|-
 
−
| 12
 
−
| 1
 
−
| A1
 
−
| Arduino_Nano_v3
 
−
|-
 
−
|}
 
−
 
 
−
==== Software ====
 
−
 
 
−
* [https://github.com/land-boards/lb-Arduino-Code/blob/master/LBCards/SYNTHS/PROTO01_POTS_CHECK/PROTO01_POTS_CHECK.ino PROTO01_POTS_CHECK.ino] - Dump pots/input jacks to screen
 
−
 
 
−
=== CV4 - 4 Control Voltages ===
 
−
 
 
−
* 4 Pots
 
−
* 4 Jacks
 
−
* Voltage Levels are assignable via jumpers
 

Latest revision as of 17:48, 18 January 2023

Tindie-mediums.png

ER-PROTO-PANEL-01-SET FRONT REAR-3D-720px.png

Features

  • Eurorack Prototyping card set
  • 6 HP wide (30mm) front panel
  • 3U tall
  • Three card set
    • Board interconnect headers duplicated on headers
    • 30mm wide front panel
    • 28mm wide panel and daughtercards
  • 6 POTS
    • Marked as RV1-RV5
    • Series resistors on pot wiper
    • All 3 pot pins brought to top header
  • 4 Jacks
    • Marked as J1-J4
    • Tip/sleeve brought to header near middle/bottom
  • Pots on top, jacks on bottom of card
    • Easier to adjust pots without bumping into pots
    • Pots more often accessed than jacks
  • Large prototyping area
    • 58 nodes with 3 holes per node (29 per "side")
  • +12V, -12V down board edges
  • 5V/GND down center of card
  • Bussed connections horizontally
  • Front Panel with generic labels
    • Cover with White on Black P-Touch labels

Connectors

  • J1-J4 are front panel connectors

Inter-card Connectors

Pots

  • J5 on the Controls card and J5 on the I/O card
  • Pot connections
    • POTx-1 is fully CW connects to wiper
    • POTx-2 is wiper
    • POTX-3 is fully CCW connects to wiper

RV Conns.PNG

  • To make pot into voltage control
    • POTx-1 (CW) = +5V
    • POTx-13CCW = GND
    • Wire RV1-1 to RV3-1 to RV5-1 on controls card
    • Wire RV1-3 to RV3-3 to RV5-3 on controls card
    • Wire RV2-1 to RV4-1 to RV6-1 on controls card
    • Wire RV2-3 to RV4-3 to RV6-3 on controls card

ER-PROTO-CTLS-6-01 J5.PNG

Jacks

  • J6 on the controls card and J37 on the I/O card

ER-PROTO-CTLS-6-01 J10.PNG

Daughtercard Connectors

J5, J37 - POT connectione

ER-PROTO-DB-01 J5.png

ER-PROTO-DB-01 J37.png

J6 - Eurorack Power

  • J6 on the I/O card
    • Eurorack power
    • 2x5 IDC
    • GATE, CV not connected

ER-PROTO-DB-01 J6.png

J10 - Jacks connections on Controls card

ER-PROTO-DB-01 J10.png

J38 - Jacks connections

ER-PROTO-DB-01 J38.png

Examples

Arduino NANO MOZZI

Arduino NANO MOZZI on ER-PROTO-01

ER-PROTO-01-NANO-MOZZI P1080687-720PX.jpg

ER-PROTO-01-NANO-MOZZI P1080693-720PX.jpg

CV4 - 4 Control Voltages

ER-CVPOTS4

ER-PROTO-01-CV4 P1090031-F B 720px.jpg

Noise Generator

Noise Generator on ER-PROTO-01

ER-PROTO-01 NOISE P1080751-720px.jpg

ER-PROTO-01 NOISE P1080755-720px.jpg

Slew Rate Controller

Slew Rate Controller on ER-PROTO-01

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=ER-PROTO-01&oldid=23472"