Difference between revisions of "LB-MEM-02"

From Land Boards Wiki
Jump to navigation Jump to search
 
(40 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[file:LB-MEM-02_REV1-FRONT-3D.png]]
+
[[file:LB-MEM-02_P1090747-720px.jpg]]
  
  
 
== Features ==
 
== Features ==
 
* 32KB SRAM
 
* 32KB SRAM
−
* EPROM
+
* 16KB EPROM
−
** Headers to jump for smaller cards
+
** Headers to select PROM bank
 
* Connects to Address/Data and Memory control lines
 
* Connects to Address/Data and Memory control lines
 
* 50x75mm card
 
* 50x75mm card
Line 16: Line 16:
  
 
=== EPROM ===
 
=== EPROM ===
 +
 +
* ATF16V8B part
 +
* [[TL866ii_Plus_Programmer]]
  
 
[[file:LB-MEM-02-PROM.PNG]]
 
[[file:LB-MEM-02-PROM.PNG]]
  
−
==== Rev 1 Parts/Jumpers ====
+
* [[LB-65CXX-01]] card has 16 KB PROM from 0xC000-0xFFFF
 +
* [[LB-6802-01]] card has 16 KB PROM from 0xC000-0xFFFF
 +
* [[LB-6809-01]] card has 16 KB PROM from 0xC000-0xFFFF
 +
* [[LB-Z80-01]] card has 8KB PROM from 0x0000-0x1FFF (upper 8KB is not used)
 +
 
 +
==== Parts/Jumpers ====
  
 +
* Square pin is pin 1
  
 
[[FILE:LB-MEM-02_REV1_MECH_Ann.png]]
 
[[FILE:LB-MEM-02_REV1_MECH_Ann.png]]
Line 26: Line 35:
 
==== 27C256/27C512 EPROMs ====
 
==== 27C256/27C512 EPROMs ====
  
−
* Card has a 16KB size
+
* Card has a 16KB size from the CPU
 
* 27C256 (32KB) and 27C512 (64KB) Flash EPROMs are commonly available
 
* 27C256 (32KB) and 27C512 (64KB) Flash EPROMs are commonly available
 
* Jumpers allow firmware banks to be selected
 
* Jumpers allow firmware banks to be selected
Line 32: Line 41:
 
** 4 banks in 27C512
 
** 4 banks in 27C512
  
−
[[file:LB-MEM-03_EPROM_27C256_512.PNG]]
+
{| class="wikitable"
 +
! EPROM
 +
! SIZE
 +
! BANKS
 +
! J6(A15/Pin1)
 +
! J2(A14/Pin27)
 +
! BANK #
 +
! LOAD OFFSET
 +
|-
 +
| 27C128
 +
| 16KB
 +
| 1
 +
| 2-3 (GND)
 +
| 2-3 (GND)
 +
| 1
 +
| 0x0000
 +
|-
 +
| 27C256
 +
| 32KB
 +
| 2
 +
| 2-3 (GND)
 +
| 1-2 (VCC)
 +
| 1
 +
| 0x0000
 +
|-
 +
| 27C256
 +
| 32KB
 +
| 2
 +
| 2-3 (GND)
 +
| 2-3 (GND)
 +
| 2
 +
| 0x4000
 +
|-
 +
| 27C512
 +
| 64KB
 +
| 4
 +
| 2-3 (GND)
 +
| 2-3 (GND)
 +
| 1
 +
| 0x0000
 +
|-
 +
| 27C512
 +
| 64KB
 +
| 4
 +
| 2-3 (GND)
 +
| 1-2 (VCC)
 +
| 2
 +
| 0x4000
 +
|-
 +
| 27C512
 +
| 64KB
 +
| 4
 +
| 1-2 (VCC)
 +
| 2-3 (GND)
 +
| 3
 +
| 0x8000
 +
|-
 +
| 27C512
 +
| 64KB
 +
| 4
 +
| 1-2 (VCC)
 +
| 1-2 (VCC)
 +
| 4
 +
| 0xC000
 +
|-
 +
|}
 +
 
 +
[[file:LB-MEM-02_EPROM_27C128_256_512.png]]
  
 
=== Backplane Connector ===
 
=== Backplane Connector ===
Line 39: Line 115:
  
 
== Mechanicals ==
 
== Mechanicals ==
 +
 +
=== Rev 3 ===
 +
 +
=== Rev 2 ===
 +
 +
[[file:LB-MEM-02_Rev2_MECH.PNG]]
 +
 +
=== Rev 1 ===
  
 
[[file:LB-MEM-02_REV1_MECH.PNG]]
 
[[file:LB-MEM-02_REV1_MECH.PNG]]
  
 
== Checkout ==
 
== Checkout ==
 +
 +
=== Rev 3 ===
 +
 +
* Adds PWR and GND on U1 (74HC04)
 +
* Adds electrolytic cap footprint
 +
 +
=== Rev 2 ===
 +
 +
* Flips 74HC04 orientation
 +
* Missing PWR and GND on U1 (74HC04)
 +
* Tested with [[LB-6809-01]] card
 +
** Works
  
 
=== Rev 1 ===
 
=== Rev 1 ===
  
−
* OK
+
* Missing PWR and GND on U1 (74HC04)
 +
** Added PWR and GND wires to nearest pins with PWR and GND
 +
* SRAM passes in TL866 in SRAM test mode
 +
* Test using [https://raw.githubusercontent.com/douggilliland/Retro-Computers/master/6809/LB-6809/ramLoop/ramLoop.asm ramLoop.asm] software
 +
** [https://raw.githubusercontent.com/douggilliland/Retro-Computers/master/6809/LB-6809/ramLoop/ramLoop.asm ramLoop.asm] code works on [http://6809.uk/ 6809 Emulator]
 +
*** Forcing an error works
 +
** Check on card without SRAM
 +
*** Controls/data look OK
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
 +
 +
=== Rev 3 ===
 +
 +
* [https://land-boards.com/LB-MEM-02/LB-MEM-02_Rev3_ibom.html Interactive BOM]
  
 
=== Rev 1 ===
 
=== Rev 1 ===
  
 
* [https://land-boards.com/LB-MEM-02/LB-MEM-02_Rev1_ibom.html Interactive BOM]
 
* [https://land-boards.com/LB-MEM-02/LB-MEM-02_Rev1_ibom.html Interactive BOM]

Latest revision as of 13:47, 16 October 2024

LB-MEM-02 P1090747-720px.jpg


Features

  • 32KB SRAM
  • 16KB EPROM
    • Headers to select PROM bank
  • Connects to Address/Data and Memory control lines
  • 50x75mm card

Design

SRAM

LB-MEM-02-SRAM.PNG

EPROM

LB-MEM-02-PROM.PNG

  • LB-65CXX-01 card has 16 KB PROM from 0xC000-0xFFFF
  • LB-6802-01 card has 16 KB PROM from 0xC000-0xFFFF
  • LB-6809-01 card has 16 KB PROM from 0xC000-0xFFFF
  • LB-Z80-01 card has 8KB PROM from 0x0000-0x1FFF (upper 8KB is not used)

Parts/Jumpers

  • Square pin is pin 1

LB-MEM-02 REV1 MECH Ann.png

27C256/27C512 EPROMs

  • Card has a 16KB size from the CPU
  • 27C256 (32KB) and 27C512 (64KB) Flash EPROMs are commonly available
  • Jumpers allow firmware banks to be selected
    • 2 banks in 27C256
    • 4 banks in 27C512
EPROM SIZE BANKS J6(A15/Pin1) J2(A14/Pin27) BANK # LOAD OFFSET
27C128 16KB 1 2-3 (GND) 2-3 (GND) 1 0x0000
27C256 32KB 2 2-3 (GND) 1-2 (VCC) 1 0x0000
27C256 32KB 2 2-3 (GND) 2-3 (GND) 2 0x4000
27C512 64KB 4 2-3 (GND) 2-3 (GND) 1 0x0000
27C512 64KB 4 2-3 (GND) 1-2 (VCC) 2 0x4000
27C512 64KB 4 1-2 (VCC) 2-3 (GND) 3 0x8000
27C512 64KB 4 1-2 (VCC) 1-2 (VCC) 4 0xC000

LB-MEM-02 EPROM 27C128 256 512.png

Backplane Connector

LB-MEM-02-BKPL.PNG

Mechanicals

Rev 3

Rev 2

LB-MEM-02 Rev2 MECH.PNG

Rev 1

LB-MEM-02 REV1 MECH.PNG

Checkout

Rev 3

  • Adds PWR and GND on U1 (74HC04)
  • Adds electrolytic cap footprint

Rev 2

  • Flips 74HC04 orientation
  • Missing PWR and GND on U1 (74HC04)
  • Tested with LB-6809-01 card
    • Works

Rev 1

  • Missing PWR and GND on U1 (74HC04)
    • Added PWR and GND wires to nearest pins with PWR and GND
  • SRAM passes in TL866 in SRAM test mode
  • Test using ramLoop.asm software

Assembly Sheet

Rev 3

Rev 1

Retrieved from "http://land-boards.com/blwiki/index.php?title=LB-MEM-02&oldid=27365"