Difference between revisions of "LB-68B50-02"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (26 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[file:LB-6850- | + | [[file:LB-6850-02_P1090749-720px.jpg]] |
== Features == | == Features == | ||
| Line 12: | Line 12: | ||
== Design == | == Design == | ||
| − | === ACIA | + | === ACIA === |
* 68B50 UART | * 68B50 UART | ||
* Baud Rate Clock (115,200 baud oscillator) | * Baud Rate Clock (115,200 baud oscillator) | ||
| − | [[file:LB-68B50- | + | [[file:LB-68B50-02_ACIA_Rev2.PNG]] |
=== PLD === | === PLD === | ||
| Line 26: | Line 26: | ||
* [[TL866ii Plus Programmer]] | * [[TL866ii Plus Programmer]] | ||
| − | [[file:LB-68B50- | + | [[file:LB-68B50-02_U2_PLD_Rev2.PNG]] |
==== LB-68B50-02_6XXX_PLD Listing ==== | ==== LB-68B50-02_6XXX_PLD Listing ==== | ||
| Line 138: | Line 138: | ||
=== Backplane === | === Backplane === | ||
| − | [[file:LB-68B50- | + | [[file:LB-68B50-02_J1_Backplane_Rev2.PNG]] |
== Mechanicals == | == Mechanicals == | ||
| Line 151: | Line 151: | ||
== Checkout == | == Checkout == | ||
| + | |||
| + | === Rev 2 Checkout === | ||
| + | |||
=== Rev 2 Changes === | === Rev 2 Changes === | ||
| Line 158: | Line 161: | ||
** Inv on one end but not on the other end on schematic | ** Inv on one end but not on the other end on schematic | ||
* Added config jumper J3 into PLD (U2-14) to allow for 2 configs | * Added config jumper J3 into PLD (U2-14) to allow for 2 configs | ||
| − | ** [[LB-65CXX-01|6502]], [[LB-6802-01|6802]], [[LB-6809-01|6809]] removed | + | ** [[LB-65CXX-01|6502]], [[LB-6802-01|6802]], [[LB-6809-01|6809]] jumper removed |
| − | ** [[LB-Z80-01|Z80]] installed | + | ** [[LB-Z80-01|Z80]] jumper installed |
* Add LED with resistor to U2-15 | * Add LED with resistor to U2-15 | ||
| + | * Moved Osc down a bit | ||
[[file:LB-6850-02_FRONT_REV2(BLK).png]] | [[file:LB-6850-02_FRONT_REV2(BLK).png]] | ||
| − | === Rev 1 === | + | === Rev 1 Checkout === |
| + | |||
| + | ==== IOCS* is on wrong pin ==== | ||
| + | |||
| + | * It is on J1-38 on the Rev 1 PCB | ||
| + | * IOCS* should be on pin J1-37 | ||
| + | * Rework | ||
| + | ** Add wire J1-37 to U2-13 | ||
| + | ** Cut trace near J1-38 | ||
| − | [[file:LB- | + | [[file:LB-68B50-02_J1-38_Rework.PNG]] |
| − | * | + | * Rev 1 before |
| − | |||
| − | |||
| − | |||
[[file:LB-68B50-02_NP_Errors-Rev2.PNG]] | [[file:LB-68B50-02_NP_Errors-Rev2.PNG]] | ||
| Line 178: | Line 187: | ||
[[file:LB-68B50-02_NP_Fixed-Rev2.PNG]] | [[file:LB-68B50-02_NP_Fixed-Rev2.PNG]] | ||
| + | |||
| + | ==== Missing IORQ signal ==== | ||
| + | |||
| + | * Inverted on one end but not on the other end on schematic | ||
| + | * Rev 1 | ||
| + | |||
| + | [[file:LB-68B50-02_U2_IORQ_Before.PNG]] | ||
| + | |||
| + | * Rev 2 | ||
| + | |||
| + | [[file:LB-68B50-02_U2_IORQ_After.PNG]] | ||
| + | |||
| + | * Rework | ||
| + | ** Add wire U2-13 to J1-51 (Z80) | ||
== Mechanicals == | == Mechanicals == | ||
Latest revision as of 13:55, 16 October 2024
Features
- Serial/Parallel I/O Card
- 68B50 UART
- 1.8432 MHz oscillator
- Baud Rate Clock (115,200 baud oscillator)
- Control PLD
- 100x50mm card
Design
ACIA
- 68B50 UART
- Baud Rate Clock (115,200 baud oscillator)
PLD
- Customize PLD per CPU type and to match memory map
- Can be used to support multiple 6850 cards
- ATF16V8B part
- TL866ii Plus Programmer
LB-68B50-02_6XXX_PLD Listing
- 6XXX (6502, 6802, 6809 specific)
Name LB-68B50-02_6XXX_PLD; Partno ATF16V8B; Date 09/20/24; Revision 01; Designer DOUG G; Company LAND BOARDS LLC; Assembly LB-68B50-02_6XXX_U2; Location Rustbelt, US; Device G16V8; /* 68B50 Control for LB-6809-01, LB-6802-01, and LB-65CXX CPU boards 0x8000-0xBFFF - 16KB I/O space */ /* Control inputs */ PIN 1 = CPUA15; PIN 2 = CPUA14; PIN 3 = CPUA13; PIN 4 = CPUA12; PIN 5 = CPUA11; PIN 6 = CPUA10; PIN 7 = CPUA1; PIN 8 = CPUA0; PIN 9 = !IOCS; /* IOCS is IO space decoded on all CPU cards */ PIN 11 = VDA; /* Not used in any version */ PIN 12 = VPB; /* VPB is enable on 6802, 6809 AND 6502 (Rev 2 rwk) CPUs */ PIN 14 = !IORQ; /* IORQ* is enable on Z80 cards */ /* Address Decode and Chip Select outputs */ PIN 16 = ACIACS1; PIN 17 = ACIACS0; PIN 18 = ACIARS; PIN 19 = ACIAE; ACIACS1 = CPUA15 & !CPUA14 & IOCS; ACIACS0 = CPUA15 & !CPUA14 & IOCS; ACIARS = CPUA0; ACIAE = CPUA15 & !CPUA14 & IOCS & VPB;
LB-68B50-02_Z80_PLD PLD Listing
Name LB-68B50-02_Z80_PLD; Partno ATF16V8B; Date 09/19/24; Revision 01; Designer DOUG G; Company LAND BOARDS LLC; Assembly LB-6850-02_U2; Location Rustbelt, US; Device G16V8; /* 68B50 Control for Z80 CPU board */ /* Control inputs */ PIN 1 = CPUA15; PIN 2 = CPUA14; PIN 3 = CPUA13; PIN 4 = CPUA12; PIN 5 = CPUA11; PIN 6 = CPUA10; PIN 7 = CPUA1; PIN 8 = CPUA0; PIN 9 = !IOCS; PIN 11 = VDA; PIN 12 = VPB; PIN 13 = !IORQ; /* Address Decode and Chip Select outputs */ PIN 16 = ACIACS1; PIN 17 = ACIACS0; PIN 18 = ACIARS; PIN 19 = ACIAE; ACIACS1 = IOCS & IORQ; ACIACS0 = IOCS & IORQ; ACIARS = CPUA0; ACIAE = IOCS & IORQ;
J2 - FTDI Header)
- 5V levels
- Pinout
- GND
- CTS (in)
- VCC
- TX (out)
- RX (in)
- RTS (out)
Backplane
Mechanicals
Rev 2
Rev 1
Checkout
Rev 2 Checkout
Rev 2 Changes
- Fixed IOCS* to be on J1-38
- Fixed IORQ signal
- Inv on one end but not on the other end on schematic
- Added config jumper J3 into PLD (U2-14) to allow for 2 configs
- Add LED with resistor to U2-15
- Moved Osc down a bit
.png)
Rev 1 Checkout
IOCS* is on wrong pin
- It is on J1-38 on the Rev 1 PCB
- IOCS* should be on pin J1-37
- Rework
- Add wire J1-37 to U2-13
- Cut trace near J1-38
- Rev 1 before
- Fixed on Rev 2 PCB
Missing IORQ signal
- Inverted on one end but not on the other end on schematic
- Rev 1
- Rev 2
- Rework
- Add wire U2-13 to J1-51 (Z80)
