Difference between revisions of "SPI-POTX2"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 63: | Line 63: | ||
=== Hardware Setup === | === Hardware Setup === | ||
| − | [[FILE:]] | + | [[FILE:SPI-POTX2_P1889_720px.jpg]] |
* [[RPI_PSOC5]] | * [[RPI_PSOC5]] | ||
Revision as of 13:31, 5 April 2022
Contents
Features
- Dual Digital potentiometer
- MCP4231 Dual Digital Pot
- 7-bit: 128 Resistors (129 Steps)
- Zero Scale to Full Scale Wiper operation
- 10K
- Other resistances optional: 5K, 50K, 100K
- Power on reset to half wiper value
- SPI Interface
- SPI Serial Interface (10 MHz, modes 0,0 & 1,1)
- High-Speed Read/Writes to wiper register
- 10 MHz (max SPI speed)
- 2.7V to 5.5V
- Daisy-chain SPI connector
- Slave Select (SS) should be star connected
- 49x49mm form factor
- (4) #4-40 mounting holes
Connectors
J1, J3 - SPI connector
- MISO
- +V
- SCK
- MOSI
- SS
- GND
J2 - SPI Connector
- Matches Arduino SPI connector pinout
- MISO
- +V
- SCK
- MOSI
- SS
- GND
POT0, POT1
- GND
- B SIDE
- WIPER
- A SIDE
- +V
Driver Software
- SPI-POT-X2 GitHub Arduino Example Code
- Creates triangle wave output on both outputs
Factory Test Procedure
- Test SPI-POTX2 card on RPI_PSOC5 Test Station
Hardware Setup
SPI Cable
| RPI_SPI8 (Marking) | RPI_SPI8 Pin | SPI-POTX2 Pin | SPI-POTX2 Marking |
|---|---|---|---|
| Chip En (CE) | 1 | 5 | SS |
| MOSI (MO) | 2 | 4 | MOSI |
| MISO (MI) | 3 | 1 | MISO |
| SPICK (CK) | 4 | 3 | SCK |
| Vcc (+V) | 5 | 2 | +V |
| GND | 6 | 6 | GND |
Run Tests
- Run puTTY
- Find COM Port in Device Manager
- 115,200 baud
- RTS/CTS flow control
- Hit ENTER to see menu
Land Boards, LLC - RPi Card Test Station 1 - Select RPP-UIO-16 Card 2 - Select RPPSOC Card 3 - Select RASPI-PLUS-GVS-CFG Card 4 - Select RASPI-GVS Card 5 - Select RASPI-PLUS-GVS Card 6 - Select RPI-I2C-HUB Card 7 - Select RPI-SPI8 Card R - Read EEPROM W - Write EEPROM B - Bounce LED across Card GPIOs T - Test Card D - Debug Card ? - Print this menu
- Select RPI-SPI8 Card by entering 7[ENTER]
7 Selected RPI-SPI8 card
Create Sawtooth Output
- Enter B[ENTER] - Create ramped output
B Blinking the RPI-SPI8 Card LEDs, please wait
- Bounces LEDs off across the LEDs
- 8 CE signals go low one at a time
- MOSI, MISO, SCK cycles one on at time
- Ramped output
Test Software
- Runs on RPI_PSOC5
- GitHub repo
- Test_RPI_SPI8.c - Bounce LED across LED-TEST-2 card
- Runs on RPI_PSOC5
- Uses RPI_SPI8
- GitHub repo
- Test_RPI_SPI8.c - Test with SPI-POTX2 card
