IOP16 ANSI Display

Multicomp FPGA (VHDL Template) VGA

Interface mimics ACIA software interface address/control/status contents

• ACIA datasheet

Programming Interface

• Two addresses, Control/status and data access

Status Register

• Register Select = 0
• Read/Write = Read
  • d0 = RDRF = Receive Data Register Full (1 = data is ready to read)
  • d1 = TDRE = Transmit Data Register Empty (1 = transmit is ready to send out data)
  • d2 = DCD = Data Carrier Detect (0 = carrier present - hardwired)
  • d3 = CTS = Clear to Send (0 = Clear to Send - ready to accept data - hardwired)
  • d7 = IRQ = Interrupt Request (1 = Interrupt present)

Control Register

• Register Select = 0
• Read/Write = Write
  • d1,d0 = Control (11 = Master Reset)
  • d6,d5 = TC = Transmitter Control (RTS = Transmitter Interrupt Enable/Disable)
  • d7 = Interrupt Enable (1=enable interrupts)

Data Register

• Register Select = 1
  • Read = Read data from the data register (not implemented due to kbd removal)
  • Write = Write data to the data register

ANSI ESC Codes

VHDL Code

Entity

-- ____________________________________________________________________________________
-- Grant Searle's VGA driver from Multicomp
-- DGG removed the PS/2 keyboard, Composite output and CTS
-- Interface matches ACIA software interface address/control/status contents

vdu : entity work.ANSIDisplayVGA
  GENERIC map (
    EXTENDED_CHARSET    => 0, -- 1 = 256 chars
                              -- 0 = 128 chars
    COLOUR_ATTS_ENABLED => 0, -- 1 = Color for each character
                              -- 0 = Color applied to whole display
    SANS_SERIF_FONT     => 1  -- 0 => use conventional CGA font
                              -- 1 => use san serif font
)
  port map (
    clk     => i_clk,
    n_reset => w_resetClean_n,
    -- CPU interface
    n_WR    => not W_VDUWr,
    n_rd    => not W_VDURd,
    regSel  => w_periphAdr(0),
    dataIn  => w_periphOut,
    dataOut => w_VDUDataOut,
    -- VGA video signals
    hSync   => hSync,
    vSync   => vSync,
    videoR0 => videoR0,
    videoR1 => videoR1,
    videoG0 => videoG0,
    videoG1 => videoG1,
    videoB0 => videoB0,
    videoB1 => videoB1
);

Signals

-- Decodes/Strobes
...
  signal W_VDUWr       : std_logic;
  signal W_VDURd       : std_logic;

-- Interfaces
...
  signal w_VDUDataOut  :  std_logic_vector(7 downto 0);

Hook-up code

-- Strobes/Selects
...
w_VDUWr <= '1' when ((w_periphAdr(7 downto 1) = "0000101") and (w_periphWr= '1')) else '0';
w_VDURd <= '1' when ((w_periphAdr(7 downto 1) = "0000101") and (w_periphRd = '1')) else '0';

-- Peripheral bus read mux
w_periphIn <=	...
  w_VDUDataOut			when w_periphAdr(7 downto 1) = "0000101"	else
...

Resources (10CL006)

• Logic Cells: 918
• Registers: 203
• Memory Bits: 24576 (128 chars)
• M9Ks: 3 (128 chars)
• Memory Bits: 32768 (256 chars)
• M9Ks: 4 (256 chars)
• Resource usage can be reduced by changing the generics below
  • EXTENDED_CHARSET=0, COLOUR_ATTS_ENABLED=0 - Uses 3 M9K blocks
  • EXTENDED_CHARSET=1, COLOUR_ATTS_ENABLED=0 - Uses 4 M9K blocks
  • EXTENDED_CHARSET=0, COLOUR_ATTS_ENABLED=1 - Uses 5 M9K blocks
  • EXTENDED_CHARSET=1, COLOUR_ATTS_ENABLED=1 - Uses 6 M9K blocks