Difference between revisions of "ER-ADSR-555-01"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
Line 102: | Line 102: | ||
* Add wire RV1-2 to RV1-1 | * Add wire RV1-2 to RV1-1 | ||
+ | |||
+ | [[FILE:RV1_JUMPER.png]] | ||
+ | |||
* Add wire RV2-2 to RV2-1 | * Add wire RV2-2 to RV2-1 | ||
+ | |||
+ | [[FILE:RV2_JUMPER.png]] | ||
+ | |||
* Add wire R10 left side to Sustain pot, RV3 right side | * Add wire R10 left side to Sustain pot, RV3 right side | ||
* Add wire U2-7 to Sustain pot, RV3 left side | * Add wire U2-7 to Sustain pot, RV3 left side | ||
+ | |||
+ | [[FILE:RV3_JUMPER.png]] | ||
+ | |||
* Add wire R10 to RV4-3 | * Add wire R10 to RV4-3 | ||
* Add wire RV4-1 to RV4-2 | * Add wire RV4-1 to RV4-2 | ||
+ | |||
+ | [[FILE:RV4_JUMPER.png]] | ||
== Assembly Sheet == | == Assembly Sheet == | ||
[[ER-ADSR-555-01 Rev 1 Assembly Sheet]] | [[ER-ADSR-555-01 Rev 1 Assembly Sheet]] |
Revision as of 18:05, 5 November 2022
Contents
Eurorack ADSR Module
Features
- Attack-DeCay-Sustain-Release Eurorack ADSR Module
- Takes in Gate signal, generates CV to VCA
- Attack, decay, and release pots control speed
- Attack, decay, and release times can range from 200ms to 16s
- Sustain pot sets the sustain voltage level
- LED dims to level
- 3U tall, 6 HP wide
- 555 Based design
- Benjie Jiao MiniADSR
- Original was based on Barry Klein design
- As built by schmitzbits design - "The Fastest Envelope in the West"
- Benji's build has a three card stack-up and is 4 HP wide
- This card is wider but uses 2 cards
Rev 1 Checkout
- Ordered wrong (earlier) version of the board
- Re-create ordered board in Rev 1 folder
- Annotated schematic
- Drive with Erica Synths EDU Sequencer
- GATE Out output
- At slowest speed, ~2Hz
- My schematic symbols are Schottky but installed 1N4148 like schmitzbits schemati
- Using 1 M linear pots instead of 2.2M log pots
- A, D, R pots should have been log pots
- Controls are are "touchy"
- Sustain pot is linear as it should be and "works" but is backwards
- All of the pots are backwards
- A, D, S pots should be CCW for no delay
- ADR series resistors are 220 Ohms but should be 100 Ohms per schmitzbits note
- C3 is 4.7 uF
- Log pot curves
- Does not have 1M that is dashed line on schmitzbits schemati
- ADSR controls
- A pot full CW
- D pot full CW
- S Pot mid
- R pot full CW
- Back off Attack just a tiny bit from CCW
- Rounds over the attack like it should but it is very "touchy"
Benjie Jiao - DIY Modular Video
Issues
Rev 1 Issues
- Silkscreen has "DELAY" should be "DECAY"
- A, D, S, R pots are all backwards
- A, D, R pots should be A1M
- Made new build
Cuts
- Cuts before build
- Cuts to RV1 (pins 2-3)
- Cuts to RV2 (pins 2-3)
- Cut to RV3
- Cuts to RV4
Change Pot Series Resistor Values
- 220 Ohms on A, D, R pots s/b 100 Ohms
- Change R7 to 100 Ohms (A pot)
- Change R8 to 100 Ohms (D pot)
- Change R10 to 100 Ohms (R pot)
Add wires
- Add wire RV1-2 to RV1-1
- Add wire RV2-2 to RV2-1
- Add wire R10 left side to Sustain pot, RV3 right side
- Add wire U2-7 to Sustain pot, RV3 left side
- Add wire R10 to RV4-3
- Add wire RV4-1 to RV4-2