Difference between revisions of "QMTECH Cyclone 10CL006 FPGA Card"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 24: | Line 24: | ||
* Power LED - D4 (On when 5V is applied) | * Power LED - D4 (On when 5V is applied) | ||
| − | * User LED - LED_D5 - FPGA | + | * User LED - LED_D5 - FPGA Pin_L9 (pull low to illuminate LED) |
| − | * KEY0 - SW1 - FPGA | + | * KEY0 - SW1 - FPGA Pin_F3 |
| − | * RESET_N- SW2 - FPGA | + | * RESET_N- SW2 - FPGA PIN_J6 |
| − | * nCONFIG - SW3 - FPGA | + | * nCONFIG - SW3 - FPGA PIN_H5 |
* JP5 - 5V | * JP5 - 5V | ||
Revision as of 11:51, 12 April 2022
Contents
Specification
- On-Board FPGA: 10CL006YU256C8G
- On-Board FPGA external crystal frequency: 50MHz
- 10CL006YU256C8G has block RAM resource - 30 of M9K blocks
- 10CL006YU256C8G has 6K LEs
- On-Board 32MB Micron SDRAM，MT48LC16M16A2-75
- On-Board 3.3V power supply for FPGA by using MP2359 wide input range DC/DC
- QM_Cyclone10_10CL006 development board has two 64p, 2.54mm pitch headers for extending user IOs
- QM_Cyclone10_10CL006 development board has 3 user switches
- QM_Cyclone10_10CL006 development board has 2 user LEDs
- QM_Cyclone10_10CL006 development board has JTAG interface, by using 10p, 2.54mm pitch male header
- QM_Cyclone10_10CL006 development board PCB size is: 6.7cm x 8.4cm
- Default power source for board is: 1A@5V DC, the DC header type: DC-050, 5.5mmx2.1mm
- AliExpress listing
Resources
- Comparable to Cyclone IV EP4CE6 FPGA
- 30 1Kx9 RAM blocks
- Power LED - D4 (On when 5V is applied)
- User LED - LED_D5 - FPGA Pin_L9 (pull low to illuminate LED)
- KEY0 - SW1 - FPGA Pin_F3
- RESET_N- SW2 - FPGA PIN_J6
- nCONFIG - SW3 - FPGA PIN_H5
- JP5 - 5V
Connectors
Configuration EEPROM
LEDs
Pushbuttons
SDRAM
U7
U8
Pin List
# Clocks, reset set_location_assignment PIN_E1 -to sys_clk set_location_assignment PIN_J6 -to RESET_N set_location_assignment PIN_L9 -to LEDR set_location_assignment PIN_F3 -to KEY # SDRAM set_location_assignment PIN_R7 -to DRAM_ADDR[0] set_location_assignment PIN_T7 -to DRAM_ADDR[1] set_location_assignment PIN_R8 -to DRAM_ADDR[2] set_location_assignment PIN_T8 -to DRAM_ADDR[3] set_location_assignment PIN_R6 -to DRAM_ADDR[4] set_location_assignment PIN_T5 -to DRAM_ADDR[5] set_location_assignment PIN_R5 -to DRAM_ADDR[6] set_location_assignment PIN_T4 -to DRAM_ADDR[7] set_location_assignment PIN_R4 -to DRAM_ADDR[8] set_location_assignment PIN_T3 -to DRAM_ADDR[9] set_location_assignment PIN_T6 -to DRAM_ADDR[10] set_location_assignment PIN_R3 -to DRAM_ADDR[11] set_location_assignment PIN_T2 -to DRAM_ADDR[12] set_location_assignment PIN_N8 -to DRAM_BA[0] set_location_assignment PIN_L8 -to DRAM_BA[1] set_location_assignment PIN_M7 -to DRAM_CAS_N set_location_assignment PIN_R1 -to DRAM_CKE set_location_assignment PIN_P2 -to DRAM_CLK set_location_assignment PIN_P8 -to DRAM_CS_N set_location_assignment PIN_N6 -to DRAM_LDQM set_location_assignment PIN_P1 -to DRAM_UDQM set_location_assignment PIN_M8 -to DRAM_RAS_N set_location_assignment PIN_P6 -to DRAM_WE_N set_location_assignment PIN_K5 -to DRAM_DQ[0] set_location_assignment PIN_L3 -to DRAM_DQ[1] set_location_assignment PIN_L4 -to DRAM_DQ[2] set_location_assignment PIN_K6 -to DRAM_DQ[3] set_location_assignment PIN_N3 -to DRAM_DQ[4] set_location_assignment PIN_M6 -to DRAM_DQ[5] set_location_assignment PIN_J2 -to DRAM_DQ[15] set_location_assignment PIN_J1 -to DRAM_DQ[14] set_location_assignment PIN_K2 -to DRAM_DQ[13] set_location_assignment PIN_K1 -to DRAM_DQ[12] set_location_assignment PIN_L2 -to DRAM_DQ[11] set_location_assignment PIN_L1 -to DRAM_DQ[10] set_location_assignment PIN_N1 -to DRAM_DQ[9] set_location_assignment PIN_N2 -to DRAM_DQ[8] set_location_assignment PIN_N5 -to DRAM_DQ[7] set_location_assignment PIN_P3 -to DRAM_DQ[6]
