Difference between revisions of "ER-PROTO-02"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| Line 21: | Line 21: | ||
** Cover with White on Black P-Touch labels | ** Cover with White on Black P-Touch labels | ||
| − | == Controls Card - Jacks/Headers/Pots == | + | == Jacks/Headers/Pots == |
| + | |||
| + | === Controls Card - Jacks/Headers/Pots === | ||
* 0-6 Jacks | * 0-6 Jacks | ||
| Line 27: | Line 29: | ||
* Headers to connect to Prototyping card | * Headers to connect to Prototyping card | ||
| − | === J1-J6 Jacks === | + | ==== J1-J6 Jacks ==== |
[[file:ER-PROTO-02_JACKS.PNG]] | [[file:ER-PROTO-02_JACKS.PNG]] | ||
| Line 34: | Line 36: | ||
** Typically Tip = 0 Ohm jumper, Ring/Switch = Do Not Populate (DNP on schematic) | ** Typically Tip = 0 Ohm jumper, Ring/Switch = Do Not Populate (DNP on schematic) | ||
| − | === J7 Header === | + | ==== J7 Header ==== |
[[file:ER-PROTO-02_jacks_J7.PNG]] | [[file:ER-PROTO-02_jacks_J7.PNG]] | ||
| Line 40: | Line 42: | ||
* 2x8 female header | * 2x8 female header | ||
| − | === J8 Header === | + | ==== J8 Header ==== |
[[file:ER-PROTO-02_pots_J8.PNG]] | [[file:ER-PROTO-02_pots_J8.PNG]] | ||
| Line 46: | Line 48: | ||
* 2x10 female headers | * 2x10 female headers | ||
| − | === Pots === | + | ==== Pots ==== |
[[file:ER-PROTO-02_POTS.PNG]] | [[file:ER-PROTO-02_POTS.PNG]] | ||
| Line 53: | Line 55: | ||
** Install jumpers if pots are used as controls voltages | ** Install jumpers if pots are used as controls voltages | ||
** Do not install jumpers if pots are used as volume control voltages | ** Do not install jumpers if pots are used as volume control voltages | ||
| + | |||
| + | === Prototyping Daughtercard === | ||
| + | |||
| + | ==== Pots ==== | ||
| + | |||
| + | [[file:ER-PROTO2-DB_J8_J28.PNG]] | ||
| + | |||
| + | ==== Jacks ==== | ||
| + | |||
| + | [[file:ER-PROTO2-DB_J7_J29.PNG]] | ||
== Examples == | == Examples == | ||
Revision as of 11:16, 24 November 2022
Contents
Features
- Eurorack Prototyping card set
- 6 HP wide (30mm) front panel
- 3U tall
- 0-6 POTS
- Series resistors on pot wiper
- All 3 pot pins brought to top header
- 0-6 Jacks
- Tip/ring brought to header near bottom
- Pots on top, jacks on bottom
- Easier to adjust pots without bumping into pots
- Pots more often accessed than jacks
- Large prototyping area
- +12V, -12V down board edges
- 5V/GND down center of card
- Bussed connections horizontally
- Front Panel with generic labels
- Cover with White on Black P-Touch labels
Jacks/Headers/Pots
Controls Card - Jacks/Headers/Pots
- 0-6 Jacks
- 0-6 Pots
- Headers to connect to Prototyping card
J1-J6 Jacks
- Jacks have resistors on Tip/Ring-Switch
- Typically Tip = 0 Ohm jumper, Ring/Switch = Do Not Populate (DNP on schematic)
J7 Header
- 2x8 female header
J8 Header
- 2x10 female headers
Pots
- Pots have optional pull-up/pulldown jumper positions
- Install jumpers if pots are used as controls voltages
- Do not install jumpers if pots are used as volume control voltages
Prototyping Daughtercard
Pots
Jacks
