Difference between revisions of "DIGIO-128 Rev X4 Assembly Sheet"

From Land Boards Wiki
Jump to navigation Jump to search
 
(12 intermediate revisions by the same user not shown)
Line 17: Line 17:
 
|  
 
|  
 
| 1
 
| 1
| CONN, 2X03
+
| Header, 2X03
 
| J4
 
| J4
 
|-
 
|-
| 1 (option)
+
| 1
| 0
+
| 0 (wire jumper)
| R7 (option - below)
+
| R7
 
|  
 
|  
 
| 2
 
| 2
| CONN, 1x4
+
| Header, 1x4
| J2,J3
+
| J2, J3
 
|-
 
|-
| 2
+
| 3
(3)
 
 
| 10K (1/4W)
 
| 10K (1/4W)
| R1,R2
+
| R1, R2, R6
R6 (option - below)
 
 
|  
 
|  
 
| 1
 
| 1
| CONN, 1x5
+
| Header, 1x5
 
| J1
 
| J1
 
|-
 
|-
Line 43: Line 41:
 
|  
 
|  
 
| 8
 
| 8
| CONN, 2x10
+
| Header, 2x10
| P1,P2,P3,P4,P6,P7,P8,P9
+
| P1-P4, P6-P9
 
|-
 
|-
 
| 2
 
| 2
Line 51: Line 49:
 
|  
 
|  
 
| 2
 
| 2
| CONN, 2X2
+
| Header, 2X2
| P10,P5
+
| P5, P10
 
|-
 
|-
 
| 1
 
| 1
Line 58: Line 56:
 
| U9
 
| U9
 
|  
 
|  
|  
+
| 3
|  
+
| Shunts
|  
+
| J4
 
|-
 
|-
 
| 8
 
| 8
 
| MCP23017P
 
| MCP23017P
| U1,U2,U3,U4,U5,U6,U7,U8
+
| U1-U8
 
|  
 
|  
 
|  
 
|  
Line 74: Line 72:
 
== R6/R7 Option ==
 
== R6/R7 Option ==
  
 +
* This option is not factory configuration
 
* R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27
 
* R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27
* R6 pulls up A2 to Vcc (only if R7 is not installed) (64-bits only)
+
** Clip out R7 jumper to shift address up (not typical use)
* R7 provide pull-up or pull-down for I2C address A2 line
 
* R7 is 0 ohm jumper
 
* R6 is 10K resistor
 
 
 
=== DIGIO-128 - 128-bit option ===
 
 
 
* Leave R6 open (no resistor)
 
* Install jumper wire into R7
 
 
 
=== DIGIO-64 - 64-bit option ===
 
 
 
* Typical - for I2C address = 0x20-0x23 leave R6 open, install jumper wire into R7
 
* For I2C address = 0x24-0x27 leave R7 open, install 10K resistor in R6
 
* I2C chips get installed into top 4 locations
 

Latest revision as of 13:18, 12 February 2021

DIGIO-128-AssySheet-X4.PNG

Parts List

Qty Value RefDes Qty Value RefDes
8 0.1uF Cap, 0.2" pitch C1-C8 1 Header, 2X03 J4
1 0 (wire jumper) R7 2 Header, 1x4 J2, J3
3 10K (1/4W) R1, R2, R6 1 Header, 1x5 J1
1 1K (1/4W) R5 8 Header, 2x10 P1-P4, P6-P9
2 2.2K (1/4W) R3,R4 2 Header, 2X2 P5, P10
1 24LC024-I/P U9 3 Shunts J4
8 MCP23017P U1-U8

R6/R7 Option

  • This option is not factory configuration
  • R6 and R7 can be used to shift the address of the 64 bit version of the card from 0x20-0x23 up to 0x24-0x27
    • Clip out R7 jumper to shift address up (not typical use)