Difference between revisions of "FTDI-49MM"

From Land Boards Wiki
Jump to navigation Jump to search
 
(9 intermediate revisions by the same user not shown)
Line 9: Line 9:
 
* FTDI compatible pinout
 
* FTDI compatible pinout
 
* 3.3V or 5V selection jumper
 
* 3.3V or 5V selection jumper
 +
* Inputs are 5V tolerant (when set to 3.3V levels)
 
* 2x6 Header for 5V power distribution
 
* 2x6 Header for 5V power distribution
 
* Rx and Tx LEDs
 
* Rx and Tx LEDs
Line 16: Line 17:
 
* Can be direct wired to [[DTE]] or [[DCE]] TTL-to-RS-232 converters
 
* Can be direct wired to [[DTE]] or [[DCE]] TTL-to-RS-232 converters
  
== Headers/Jumpers ==
+
== Headers/Jumpers/Connectors ==
  
 
=== 5V/3.3V Jumper ===
 
=== 5V/3.3V Jumper ===
Line 22: Line 23:
 
* Select 5V or 3.3V signal levels on FTDI connector
 
* Select 5V or 3.3V signal levels on FTDI connector
 
* On FTDI connector VCC pin pin 3
 
* On FTDI connector VCC pin pin 3
 +
(Inputs are 5V tolerant (when set to 3.3V levels)
  
 
=== FTDI Connector ===
 
=== FTDI Connector ===
 +
 +
* Right angle 1x6 pins
  
 
# GND
 
# GND
Line 50: Line 54:
 
[[File:OPTOUSB_Tester_Card-Annotated-720pxV.jpg]]
 
[[File:OPTOUSB_Tester_Card-Annotated-720pxV.jpg]]
  
* Connect test card to UUT
+
* UUT card
 +
* Connect [[OPTOUSB#Card_Test|OPTOUSB tester card]] to UUT
 
** Connect FTDI - black = ground
 
** Connect FTDI - black = ground
 
** Does not require LEDs connections
 
** Does not require LEDs connections
 
** Does not require 5V  Power Supply (used for [[OPTOUSB]] card)
 
** Does not require 5V  Power Supply (used for [[OPTOUSB]] card)
* Test card
 
 
* Plug in USB to computer
 
* Plug in USB to computer
 
** Should hear Windoze detect sound
 
** Should hear Windoze detect sound
Line 80: Line 84:
 
** Move middle jumper to to left position (hardware handshake on)
 
** Move middle jumper to to left position (hardware handshake on)
 
** Characters that were buffered should come in at once
 
** Characters that were buffered should come in at once
 +
* Mark test coupon on rear of card
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
  
 
[[FTDI-49MM Assembly Sheet]]
 
[[FTDI-49MM Assembly Sheet]]

Latest revision as of 19:58, 16 October 2021

Tindie-mediums.png

FTDI-P1746-CROPPED-720PX.jpg

Features

  • FT230X USB-to-FTDI Serial IC
  • USB B connector (not micro or mini, but the beefy USB B connector)
  • FTDI compatible pinout
  • 3.3V or 5V selection jumper
  • Inputs are 5V tolerant (when set to 3.3V levels)
  • 2x6 Header for 5V power distribution
  • Rx and Tx LEDs
  • (4) 4-40 mounting holes
  • Can be direct wired to DTE or DCE TTL-to-RS-232 converters

Headers/Jumpers/Connectors

5V/3.3V Jumper

  • Select 5V or 3.3V signal levels on FTDI connector
  • On FTDI connector VCC pin pin 3

(Inputs are 5V tolerant (when set to 3.3V levels)

FTDI Connector

  • Right angle 1x6 pins
  1. GND
  2. CTSn (IN)
  3. VCC
  4. TX (OUT)
  5. RX (IN)
  6. RTSn (OUT)

USB Connector

  • USB B Connector

Stackup with EP2 FPGA card

  • Top to bottom of stackup
  1. EP2C5-DB
  2. Cyclone_II_EP2C5_Mini_Dev_Board Card
  3. FTDI-49MM - (this card)
  4. CARRIER95TO49MM

P1752-CROPPED-720PX.jpg

Card Test

OPTOUSB Tester Card-Annotated-720pxV.jpg

  • UUT card
  • Connect OPTOUSB tester card to UUT
    • Connect FTDI - black = ground
    • Does not require LEDs connections
    • Does not require 5V Power Supply (used for OPTOUSB card)
  • Plug in USB to computer
    • Should hear Windoze detect sound
    • Use Device Manager to determine which COM port is used
  • Run puTTY
    • Baud rate = 115,200 baud
    • Hardware handshake RTS/CTS
    • COM port from Device Manager
  • Jumper Settings - Normal operation
    • Left jumper in right position (loopback data)
    • Middle jumper in left position (handshake = active/ground)
    • Right jumper in right position (loopback handshake)
    • Type on keyboard and verify it returns data
    • Verify both LEDs on the UUT light
  • Jumper settings - Test Tx/Rx isolation
    • Move left jumper to left position
    • Type data nothing should come back
    • Verify RX LED on the UUT only lights
    • Move left jumper to right position
  • Jumper settings - Test RTS/CTS
    • Move right jumper to left position (handshake controlled by middle jumper)
    • Type and characters should return
    • Move middle jumper to to right position (hardware handshake off)
    • Type and nothing should go through
    • Move middle jumper to to left position (hardware handshake on)
    • Characters that were buffered should come in at once
  • Mark test coupon on rear of card

Assembly Sheet

FTDI-49MM Assembly Sheet