Difference between revisions of "HW-9 VFO"

From Land Boards Wiki
Jump to navigation Jump to search
 
(3 intermediate revisions by the same user not shown)
Line 195: Line 195:
  
 
== Videos ==
 
== Videos ==
 +
 +
=== VFO Design ===
  
 
<video type="youtube">58G5atwBX2M</video>
 
<video type="youtube">58G5atwBX2M</video>
Line 208: Line 210:
 
* [https://www.youtube.com/c/CharlieMorrisZL2CTM/videos Charlie Morris YouTube channel]
 
* [https://www.youtube.com/c/CharlieMorrisZL2CTM/videos Charlie Morris YouTube channel]
  
== HW-9 Mods ==
+
=== Misc videos ===
 +
 
 +
<video type="youtube">rPM1vvGorTo</video>
 +
 
 +
=== Mods ===
  
 
<video type="youtube">rABYJi0vm7g</video>
 
<video type="youtube">rABYJi0vm7g</video>
4 Led's in the HW-9 taking only 5 MA when wired in series with a 2200 ohm 1/4 watt resistor . A total of 20 MA to light the dial and meter. The space between the front panel and the chassis here is very small so the tiny LED's are required to do the job .
+
 
 +
* 4 Led's in the HW-9 taking only 5 MA when wired in series with a 2200 ohm 1/4 watt resistor.  
 +
* A total of 20 MA to light the dial and meter.  
 +
* The space between the front panel and the chassis here is very small so the tiny LED's are required to do the job .

Latest revision as of 10:38, 30 October 2020

This is a work in process - Gathering pieces.

HW-9.PNG

Features

Replace HW-9 internal VFO with a digital VFO

  • HW-9 VFO has legendary issues
    • Mechanical issues with vernier
    • Drift due to thermal
    • Lack of resolution
    • Backwards dial
  • Fits within HW-9 VFO Box
  • Controls Tx/Rx/BFO frequencies with rotary encoder
    • 10 Hz steps
  • DD1306 OLED Display
    • I2C Interface
    • "Curved" display
  • Uses RIT control on HW-9
    • +/- 1 KHz RIT
  • Blue Pill Microprocessor
    • Arduino compatible
    • 3.3V
  • Understands band switch for MHz displayed
  • Si5351 Oscillator
    • I2C Interface
    • 3 Outputs
      • Transmit frequency
      • Receiver frequency include offset plus RIT
      • BFO frequency
    • Low pass filters to turn square waves to sine waves
    • 27 MHz crystal

Schematic

VFO-001-SCHEMATIC.PNG

Connections to Radio

  • RIT pot
    • Connects to Analog input
      • Polled occasionally while in receive
  • Band switch
    • SW1 9V
  • T/R - transmit/receive

Parts

Blue Pill Card

STM32F103C8T6-Blue-Pill-Pin-Layout.gif

  • 3.3V operation work without level shifters for I2C
    • OLED can run from 3.3V
    • Si5351 can only run from 3.3V
  • Used right angle headers and Dupont cables
  • Replaced BOOT 0,1 jumpers
    • Jumper on BOOT1
    • Switch on BOOT0 - easier to download code
  • Download via serial
  • Arduino IDE

128x32 OLED

Si5351 003 720px.jpg

OLED128x32.PNG

Arduino Library for OLED

U8G2_SSD1306_128X32_UNIVISION_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // STM32, Ebay OLED
  u8g2.setFont(u8g2_font_ncenB14_tr);
Hello World Code
U8G2_SSD1306_128X32_UNIVISION_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // STM32, Ebay OLED

void setup(void) {
  u8g2.begin();
}

void loop(void) {
  u8g2.clearBuffer();			// clear the internal memory
  u8g2.setFont(u8g2_font_ncenB08_tr);	// choose a suitable font
  u8g2.drawStr(0,10,"Hello World!");	// write something to the internal memory
  u8g2.sendBuffer();			// transfer internal memory to the display
  delay(1000);  
}

Rotary Encoder/Breakout Board

RotaryEncoderCAD.PNG


Si5351 004 720px.jpg

Si5351 Frequency Generator

Si5351 001 720px.jpg

VFO3.PNG

  • I2C Daisy-chain connector
  • 3 outputs
    • Tx
    • Rx (may not need to use separate output)
    • BFO - could be adjusted

Si5351 002 720px.jpg

Measurements

VFO TX

  • 250 KHz range
    • From 5.9993-5.7493 MHz

VFO RX

  • RIT knob is taken in through an A/D and adjusts the receive frequency plus/minus 1 KHz

BFO

  • 8.8314 MHz in receive
  • 8.8307 MHz in transmit
  • 700 Hz difference but could be adjusted

Low Pass Filters

LPF.1.5.sch.png

LPF.1.5.pcb.png


LCFilterValues.PNG

  • VFO and BFO frequencies are outside the bands (deliberately to void collisions)

BFO Filter

  • 8.8314 MHz in receive
  • 8.8307 MHz in transmit

BFO Filter.PNG

BFO Filter IL.PNG

Libraries/Example Code

Videos

VFO Design

Misc videos

Mods

  • 4 Led's in the HW-9 taking only 5 MA when wired in series with a 2200 ohm 1/4 watt resistor.
  • A total of 20 MA to light the dial and meter.
  • The space between the front panel and the chassis here is very small so the tiny LED's are required to do the job .