Difference between revisions of "LED32-DB37"

From Land Boards Wiki
Jump to navigation Jump to search
 
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/32-led-card-pwb-only-or-assembled/]]
 
[[File:tindie-mediums.png|link=https://www.tindie.com/products/land_boards/32-led-card-pwb-only-or-assembled/]]
  
−
[[File:LED32-DB37-fRONT-3D.png]]
+
[[File:LED32-DB37_P1090239-720PX.jpg]]
  
 
== Features ==
 
== Features ==
Line 7: Line 7:
 
* 32 LEDs
 
* 32 LEDs
 
* 95mm wide (ODAS width) - 55mm depth matches other ODAS cards ODAS-PSOC5 (Rev X3 or higher), DIGIO32-I2C, etc
 
* 95mm wide (ODAS width) - 55mm depth matches other ODAS cards ODAS-PSOC5 (Rev X3 or higher), DIGIO32-I2C, etc
−
* DB-37 connector
+
* DB-37 male connector
 
* (5) Ground pins (common ground)
 
* (5) Ground pins (common ground)
 
* 3mm LEDs
 
* 3mm LEDs
Line 21: Line 21:
 
* With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.
 
* With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.
  
−
== Pinout ==
+
== Wiring ==
 +
 
 +
* Male and female connectors are flipped
 +
* Female from front
 +
 
 +
[[file:DC37_F.jpg]]
 +
 
 +
* Male from front
 +
 
 +
[[file:DC37_M.jpg]]
 +
 
 +
{| class="wikitable"
 +
! LED
 +
! DB37 Female
 +
! DB37 Male
 +
!
 +
! LED
 +
! DB37 Female
 +
! DB37 Male
 +
|-
 +
| GND
 +
| 1
 +
| 19
 +
|
 +
| GND
 +
| 20
 +
| 37
 +
|-
 +
| 0
 +
| 2
 +
| 18
 +
|
 +
| 16
 +
| 21
 +
| 36
 +
|-
 +
| 1
 +
| 3
 +
| 17
 +
|
 +
| 17
 +
| 22
 +
| 35
 +
|-
 +
| 2
 +
| 4
 +
| 16
 +
|
 +
| 18
 +
| 23
 +
| 34
 +
|-
 +
| 3
 +
| 5
 +
| 15
 +
|
 +
| 19
 +
| 24
 +
| 33
 +
|-
 +
| 4
 +
| 6
 +
| 14
 +
|
 +
| 20
 +
| 25
 +
| 32
 +
|-
 +
| 5
 +
| 7
 +
| 13
 +
|
 +
| 21
 +
| 26
 +
| 31
 +
|-
 +
| 6
 +
| 8
 +
| 12
 +
|
 +
| 22
 +
| 27
 +
| 30
 +
|-
 +
| 7
 +
| 9
 +
| 11
 +
|
 +
| 23
 +
| 28
 +
| 29
 +
|-
 +
| 8
 +
| 10
 +
| 10
 +
|
 +
| 24
 +
| 29
 +
| 28
 +
|-
 +
| 9
 +
| 11
 +
| 9
 +
|
 +
| 25
 +
| 30
 +
| 27
 +
|-
 +
| 10
 +
| 12
 +
| 8
 +
|
 +
| 26
 +
| 31
 +
| 26
 +
|-
 +
| 11
 +
| 13
 +
| 7
 +
|
 +
| 27
 +
| 32
 +
| 25
 +
|-
 +
| 12
 +
| 14
 +
| 6
 +
|
 +
| 28
 +
| 33
 +
| 24
 +
|-
 +
| 13
 +
| 15
 +
| 5
 +
|
 +
| 29
 +
| 34
 +
| 23
 +
|-
 +
| 14
 +
| 16
 +
| 4
 +
|
 +
| 30
 +
| 35
 +
| 22
 +
|-
 +
| 15
 +
| 17
 +
| 3
 +
|
 +
| 31
 +
| 36
 +
| 21
 +
|-
 +
| GND
 +
| 18
 +
| 2
 +
|
 +
| GND
 +
| 37
 +
| 20
 +
|-
 +
| GND
 +
| 19
 +
| 1
 +
|
 +
|
 +
|
 +
|
 +
|-
 +
|}
 +
 
 +
== Test Procedure ==
 +
 
 +
=== Setup ===
 +
 
 +
* LED32-DB37 - Unit Under Test (UUT)
 +
* [[PiPicoMite02 Based Test Station]]
 +
** [[PiPicoMite02]] Processor card
 +
* (2) [[DB37RIBBON]] cards
 +
* (2) of 2x10 cables to connect between [[DB37RIBBON]] cards and UUT
 +
* LED32-1 marked on cable end goes near HDR1 marked on UUT
 +
 
 +
=== Card Test Procedure ===
 +
 
 +
* Power up Test Station/UUT
 +
* Type
 +
 
 +
<pre>
 +
chdir "/lbcards/GPIO32"
 +
load " GPIO32-01.bas"
 +
run
 +
 
 +
</pre>
 +
 
 +
* Should see the LEDs go around the UUT card
 +
* Hit any key to stop (after finishing rotation)
 +
 
 +
== Rear Side Marking ==
 +
 
 +
[[file:LED32-DB37_P1090242-720PX.jpg]]
 +
 
 +
== Mechanicals ==
 +
 
 +
[[file:led32-db37_mechs.PNG]]
  
 
== Assembly Sheet ==
 
== Assembly Sheet ==
  
 
* [[LED32-DB37 Assembly Sheet]]
 
* [[LED32-DB37 Assembly Sheet]]

Latest revision as of 20:30, 14 March 2023

Tindie-mediums.png

LED32-DB37 P1090239-720PX.jpg

Features

  • 32 LEDs
  • 95mm wide (ODAS width) - 55mm depth matches other ODAS cards ODAS-PSOC5 (Rev X3 or higher), DIGIO32-I2C, etc
  • DB-37 male connector
  • (5) Ground pins (common ground)
  • 3mm LEDs
  • 6-32 mounting holes

Series resistor - let us know what value you want

  • Series Resistor Values
  • Pick a series resistor value assuming the LED forward voltage is about 2V.
  • Operating with 3.3V will require a smaller resistance than operating at 5V for the same current.
  • Standard series resistor values we carry are: 120, 150, 200, 220, 240, 270, 330, 470, 560, and 1K.
  • For 5V operation and not too bright LED (comfortable value for front panels) we use 560 ohms.
  • With 3V across 560 ohms that's only 5 mA (for 560 ohm resistor). For something with a lot of LEDs if they are too bright it can get annoying.

Wiring

  • Male and female connectors are flipped
  • Female from front

DC37 F.jpg

  • Male from front

DC37 M.jpg

LED DB37 Female DB37 Male LED DB37 Female DB37 Male
GND 1 19 GND 20 37
0 2 18 16 21 36
1 3 17 17 22 35
2 4 16 18 23 34
3 5 15 19 24 33
4 6 14 20 25 32
5 7 13 21 26 31
6 8 12 22 27 30
7 9 11 23 28 29
8 10 10 24 29 28
9 11 9 25 30 27
10 12 8 26 31 26
11 13 7 27 32 25
12 14 6 28 33 24
13 15 5 29 34 23
14 16 4 30 35 22
15 17 3 31 36 21
GND 18 2 GND 37 20
GND 19 1

Test Procedure

Setup

Card Test Procedure

  • Power up Test Station/UUT
  • Type
chdir "/lbcards/GPIO32"
load " GPIO32-01.bas"
run
  • Should see the LEDs go around the UUT card
  • Hit any key to stop (after finishing rotation)

Rear Side Marking

LED32-DB37 P1090242-720PX.jpg

Mechanicals

Led32-db37 mechs.PNG

Assembly Sheet

Retrieved from "http://land-boards.com/blwiki/index.php?title=LED32-DB37&oldid=24768"