Difference between revisions of "MyMenu Assembly Sheet"

From Land Boards Wiki
Jump to navigation Jump to search
 
(6 intermediate revisions by the same user not shown)
Line 13: Line 13:
 
|-
 
|-
 
|3
 
|3
|0
+
|0 (0805)
 
|R14,R16,R18
 
|R14,R16,R18
 
|
 
|
 
|3
 
|3
|LED
+
|LED (0805)
 
|D1-D3
 
|D1-D3
 
|-
 
|-
 
|4
 
|4
|0/OP
+
|0/OPEN  (0805)
 
|R10,R11,R20,R21
 
|R10,R11,R20,R21
 
|
 
|
Line 29: Line 29:
 
|-
 
|-
 
|6
 
|6
|10K
+
|10K (0805)
 
|R6-R9,R12,R19
 
|R6-R9,R12,R19
 
|
 
|
 
|1
 
|1
|CONN_5
+
|CONN, 5x1
 
|P2
 
|P2
 
|-
 
|-
 
|2
 
|2
|2.2K
+
|2.2K (0805)
 
|R1,R2
 
|R1,R2
 
|
 
|
 
|5
 
|5
|SW_PUSH_OMRON
+
|SW_PUSH, 6mm
 
|SW1-SW5
 
|SW1-SW5
 
|-
 
|-
 
|3
 
|3
|330
+
|330 (0805)
 
|R3-R5
 
|R3-R5
 
|
 
|
 
|1
 
|1
|MCP23008SO
+
|[https://ww1.microchip.com/downloads/en/DeviceDoc/21919e.pdf MCP23008SO]
 
|U1
 
|U1
 
|-
 
|-
 
|3
 
|3
|DNP
+
|DNP (0805)
 
|R13,R15,R17
 
|R13,R15,R17
 
|
 
|
Line 61: Line 61:
 
|-
 
|-
 
|}
 
|}
 +
 +
== OLED Card Power Option ==
 +
 +
OLEDS cards have varying power/ground pinouts. Install 0 ohm resistors or leave open resistors to match pinout of OLED card used
 +
 +
=== OLED card pin 1 = Vcc case, pin 2 = GND ===
 +
 +
* Install R10, R21 = 0 ohms for pin 1 = VCC, pin 2 = GND
 +
* R11, R20 left open
 +
 +
=== OLED card pin 1 = GND case for pin 1 = GND, pin 2 = VCC ===
 +
 +
* Install R11, R20 = 0 ohms for pin 1 = GND case
 +
* R10, R21 left open

Latest revision as of 18:34, 6 June 2022

MyMenu-X3-AssySheet.PNG

Parts List

Qty Value RefDes Qty Value RefDes
3 0 (0805) R14,R16,R18 3 LED (0805) D1-D3
4 0/OPEN (0805) R10,R11,R20,R21 2 CONN_4 P1,P3
6 10K (0805) R6-R9,R12,R19 1 CONN, 5x1 P2
2 2.2K (0805) R1,R2 5 SW_PUSH, 6mm SW1-SW5
3 330 (0805) R3-R5 1 MCP23008SO U1
3 DNP (0805) R13,R15,R17

OLED Card Power Option

OLEDS cards have varying power/ground pinouts. Install 0 ohm resistors or leave open resistors to match pinout of OLED card used

OLED card pin 1 = Vcc case, pin 2 = GND

  • Install R10, R21 = 0 ohms for pin 1 = VCC, pin 2 = GND
  • R11, R20 left open

OLED card pin 1 = GND case for pin 1 = GND, pin 2 = VCC

  • Install R11, R20 = 0 ohms for pin 1 = GND case
  • R10, R21 left open