Difference between revisions of "NanoVNA"

From Land Boards Wiki
Jump to navigation Jump to search
 
(14 intermediate revisions by the same user not shown)
Line 19: Line 19:
 
** USB 5V 120mA
 
** USB 5V 120mA
 
** Maximum charging current 0.8A
 
** Maximum charging current 0.8A
 +
 +
=== Resources ===
 +
 
* nanovna users nanovna-users@groups.io
 
* nanovna users nanovna-users@groups.io
 
* [https://www.amazon.com/s?k=NanoVNA&ref=nb_sb_noss_2 Amazon links]
 
* [https://www.amazon.com/s?k=NanoVNA&ref=nb_sb_noss_2 Amazon links]
 +
* [https://abracon.com/uploads/resources/Abracon-White-Paper-Antenna-Impedance-Matching.pdf Antenna Impedance Matching Simplified] - Abracon White Paper
 +
* [https://nanovna.com/?page_id=46 How to read NanoVNA screen]
  
 
== Adding a battery ==
 
== Adding a battery ==
Line 47: Line 52:
  
 
* [https://www.aliexpress.com/item/4001015355411.html?spm=a2g0s.9042311.0.0.21f34c4dHoOWrm AliExpress listing]
 
* [https://www.aliexpress.com/item/4001015355411.html?spm=a2g0s.9042311.0.0.21f34c4dHoOWrm AliExpress listing]
* Testboard mainboard X1
+
* Board
* SMA female X6
+
* SMA female connectors X6
* 6mm copper stud X4
+
* 6mm standoffs X4
* M2.5 screw X4
+
* M2.5 screw X4 (for standoffs)
* 40pin round row seat x2
+
* 49 pin machine contact array (7x7)
* 0805 49r9 calibration resistance x2
+
* (2) 0805 49r9 calibration resistance
 +
** 1 spare)
 +
** Installed 49.9 ohm resistor on upper left SMA
 +
** Installed 0 ohm resistor on upper right SMA (not in kit)
 +
 
 +
[[file:RFTestBoard-3B.png]]
  
 
[[File:RF-test-03.jpg]]
 
[[File:RF-test-03.jpg]]
  
 
== Dual Band Dipole Measurements ==
 
== Dual Band Dipole Measurements ==
 +
 +
* NanoVNA sweeping from 3.5 MHz to 30 MHz
 +
 +
[[file:Dipole_20-40.png]]
  
 
* Following this setup
 
* Following this setup
Line 76: Line 90:
 
* 20 Meter SWR sweep
 
* 20 Meter SWR sweep
  
[[File:SWR_20M-720px.jpg]]
+
[[File:SWR_Dipole_20M_sweep.png]]
  
 
* 40 Meter SWR sweep
 
* 40 Meter SWR sweep
  
[[File:SWR_40M-720px.jpg]]
+
[[File:SWR_Dipole_40M_sweep.png]]
  
 
* 15 Meter SWR  
 
* 15 Meter SWR  
  
[[File:SWR_15M-02-720px.jpg]]
+
[[File:SWR_Dipole_15M_sweep.png]]
  
 
== YouTube Videos ==
 
== YouTube Videos ==
Line 127: Line 141:
  
 
<video type="youtube">R5iYuGLvlas</video>
 
<video type="youtube">R5iYuGLvlas</video>
 +
 +
<video type="youtube">iJ1qKE5O0bY</video>

Latest revision as of 18:41, 14 October 2021

NanoVNA - Network Analyzer

715RBejXZJL-Half.jpg

Specifications

  • Number of Calibration Points: 101 (Fixed)
  • Number of Scanning Points: 101 (Fixed)
  • Display Tracking: 4, Marking: 4, Save Setting : 5
  • PCB: 54mm x 85.5mm x 11mm (without the size of connectors, switches)
  • Measurement Frequency: 50KHz ~ 300MHz (50KHz -900MHz, enable extended firmware)
  • RF Output: -13dbm (maximum -9dbm)
  • Frequency Accuracy: 0.5ppm
  • Measurement Range: 70dB (50kHz-300MHz), 50dB (300M-600MHz), 40dB (600M-900MHz) enable extended firmware)
  • Port SWR: 1.1
  • Display: 2.8 inch TFT (320 x240)
  • USB Interface: USB Type-C; Communications Mode: CDC (Serial)
  • Power Supply
    • USB 5V 120mA
    • Maximum charging current 0.8A

Resources

Adding a battery

  • My unit did not come with a battery
  • Added an SMT mount ST connector to the board
  • Added an 850 mAh LiPo battery
  • The pinout on the card was backwards from the pinout of the connector at the end of the battery wires
    • Removed the pins from the battery wire connector and flipped the pins
  • Charging works
  • Battery is a bit too thick to screw the back on completely
  • Switched to longer standoffs
  • Someone else's page (they added an inline connector and wired to the card)

Software

Test Jigs

RF Demo Kit

  • AliExpress listing
  • Board
  • SMA female connectors X6
  • 6mm standoffs X4
  • M2.5 screw X4 (for standoffs)
  • 49 pin machine contact array (7x7)
  • (2) 0805 49r9 calibration resistance
    • 1 spare)
    • Installed 49.9 ohm resistor on upper left SMA
    • Installed 0 ohm resistor on upper right SMA (not in kit)

RFTestBoard-3B.png

RF-test-03.jpg

Dual Band Dipole Measurements

  • NanoVNA sweeping from 3.5 MHz to 30 MHz

Dipole 20-40.png

  • Following this setup

  • Documenting the setup / measurements of SWR on 20M/40M/15M

  • Dual band dipole from 3rd floor attic eaves to fence post

Antenna 20 40M Dipole.jpg

  • 20 Meter SWR sweep

SWR Dipole 20M sweep.png

  • 40 Meter SWR sweep

SWR Dipole 40M sweep.png

  • 15 Meter SWR

SWR Dipole 15M sweep.png

YouTube Videos

Youtube PlayList

W2AEW Videos

Other Videos