Difference between revisions of "NanoVNA"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (13 intermediate revisions by the same user not shown) | |||
| Line 19: | Line 19: | ||
** USB 5V 120mA | ** USB 5V 120mA | ||
** Maximum charging current 0.8A | ** Maximum charging current 0.8A | ||
| + | |||
| + | === Resources === | ||
| + | |||
* nanovna users nanovna-users@groups.io | * nanovna users nanovna-users@groups.io | ||
* [https://www.amazon.com/s?k=NanoVNA&ref=nb_sb_noss_2 Amazon links] | * [https://www.amazon.com/s?k=NanoVNA&ref=nb_sb_noss_2 Amazon links] | ||
| + | * [https://abracon.com/uploads/resources/Abracon-White-Paper-Antenna-Impedance-Matching.pdf Antenna Impedance Matching Simplified] - Abracon White Paper | ||
| + | * [https://nanovna.com/?page_id=46 How to read NanoVNA screen] | ||
== Adding a battery == | == Adding a battery == | ||
| Line 52: | Line 57: | ||
* M2.5 screw X4 (for standoffs) | * M2.5 screw X4 (for standoffs) | ||
* 49 pin machine contact array (7x7) | * 49 pin machine contact array (7x7) | ||
| − | * (2) 0805 49r9 calibration resistance | + | * (2) 0805 49r9 calibration resistance |
| − | * Installed 49.9 ohm resistor on upper left SMA | + | ** 1 spare) |
| − | * Installed 0 ohm resistor on upper right SMA | + | ** Installed 49.9 ohm resistor on upper left SMA |
| + | ** Installed 0 ohm resistor on upper right SMA (not in kit) | ||
| + | |||
| + | [[file:RFTestBoard-3B.png]] | ||
[[File:RF-test-03.jpg]] | [[File:RF-test-03.jpg]] | ||
== Dual Band Dipole Measurements == | == Dual Band Dipole Measurements == | ||
| + | |||
| + | * NanoVNA sweeping from 3.5 MHz to 30 MHz | ||
| + | |||
| + | [[file:Dipole_20-40.png]] | ||
* Following this setup | * Following this setup | ||
| Line 78: | Line 90: | ||
* 20 Meter SWR sweep | * 20 Meter SWR sweep | ||
| − | [[File: | + | [[File:SWR_Dipole_20M_sweep.png]] |
* 40 Meter SWR sweep | * 40 Meter SWR sweep | ||
| − | [[File: | + | [[File:SWR_Dipole_40M_sweep.png]] |
* 15 Meter SWR | * 15 Meter SWR | ||
| − | [[File: | + | [[File:SWR_Dipole_15M_sweep.png]] |
== YouTube Videos == | == YouTube Videos == | ||
| Line 129: | Line 141: | ||
<video type="youtube">R5iYuGLvlas</video> | <video type="youtube">R5iYuGLvlas</video> | ||
| + | |||
| + | <video type="youtube">iJ1qKE5O0bY</video> | ||
Latest revision as of 18:41, 14 October 2021
Contents
NanoVNA - Network Analyzer
Specifications
- Number of Calibration Points: 101 (Fixed)
- Number of Scanning Points: 101 (Fixed)
- Display Tracking: 4, Marking: 4, Save Setting : 5
- PCB: 54mm x 85.5mm x 11mm (without the size of connectors, switches)
- Measurement Frequency: 50KHz ~ 300MHz (50KHz -900MHz, enable extended firmware)
- RF Output: -13dbm (maximum -9dbm)
- Frequency Accuracy: 0.5ppm
- Measurement Range: 70dB (50kHz-300MHz), 50dB (300M-600MHz), 40dB (600M-900MHz) enable extended firmware)
- Port SWR: 1.1
- Display: 2.8 inch TFT (320 x240)
- USB Interface: USB Type-C; Communications Mode: CDC (Serial)
- Power Supply
- USB 5V 120mA
- Maximum charging current 0.8A
Resources
- nanovna users nanovna-users@groups.io
- Amazon links
- Antenna Impedance Matching Simplified - Abracon White Paper
- How to read NanoVNA screen
Adding a battery
- My unit did not come with a battery
- Added an SMT mount ST connector to the board
- Added an 850 mAh LiPo battery
- The pinout on the card was backwards from the pinout of the connector at the end of the battery wires
- Removed the pins from the battery wire connector and flipped the pins
- Charging works
- Battery is a bit too thick to screw the back on completely
- Switched to longer standoffs
- Someone else's page (they added an inline connector and wired to the card)
Software
Test Jigs
RF Demo Kit
- AliExpress listing
- Board
- SMA female connectors X6
- 6mm standoffs X4
- M2.5 screw X4 (for standoffs)
- 49 pin machine contact array (7x7)
- (2) 0805 49r9 calibration resistance
- 1 spare)
- Installed 49.9 ohm resistor on upper left SMA
- Installed 0 ohm resistor on upper right SMA (not in kit)
Dual Band Dipole Measurements
- NanoVNA sweeping from 3.5 MHz to 30 MHz
- Following this setup
- Documenting the setup / measurements of SWR on 20M/40M/15M
- Dual band dipole from 3rd floor attic eaves to fence post
- 20 Meter SWR sweep
- 40 Meter SWR sweep
- 15 Meter SWR
YouTube Videos
W2AEW Videos
Other Videos
